Wells H-2412G - Manuals - manualsarea.com

Page 2 - LIMITED WARRANTY STATEMENT; xi

M 228 306916 Op M H-2412 In stan t- On Dual Pilo t Gas Hotplate Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months fr...

Page 4 - FEATURES & OPERATING CONTROLS

BURNERS Provide cooking heat Front and rear burners are individually controllable Removable for easy cleaning BURNER CONTROL Provide individual control of front and rear burners KNOBS PILOT LIGHT Provides ignition source for main burners ACTUATOR Admits gas to burner when depressed. Actuator head re...

Page 5 - FIRE HAZARD; PRECAUTIONS AND GENERAL INFORMATION; AGENCY APPROVAL INFORMATION; US

This appliance is intended for use in commercial establishments only. This appliance is intended to prepare food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. This hotplate must be installed by a technician qualified and certified or licensed to ...

Page 6 - INSTALLATION; DO NOT discard; UNPACKING & INSPECTION; Carefully read all instructions in this manual and the; SETUP; Clearances to adjacent surfaces must be maintained.; Maintain adequate clearances for cleaning and proper operation.; Standard for the Installation of

INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. DANGER: HEALTH HAZARD This appliance must be properl...

Page 7 - Massachusetts Fuel Gas and Plumbing; HAZARD

INSTALLATION (continued) GAS APPLIANCE CODE COMPLIANCE The installation of gas piping from the outlet side of the gas meter or service regulator to the hotplate must be performed by a technician qualified and certified or licensed to install gas-fired equipment. A licensed and qualified technician m...

Page 8 - INSTALLING THE HOTPLATE; It is the responsibility of the gas piping installer to; Fig. 2 Gas Supply Piping

INSTALLATION (continued) INSTALLING THE HOTPLATE Refer to the nameplate. Verify the fuel type and pressure, which must match the nameplate specifications. Connecting the hotplate to the wrong fuel type and/or pressure will compromise the safety and/or performance of the appliance. The hotplate must ...

Page 9 - INITIAL ADJUSTMENT; BURN HAZARD

INITIAL ADJUSTMENT SET GAS PRESSURE: Turn the gas shut-off valve OFF . A gas pressure test tap is provided on the gas supply manifold. Remove both burner control knobs and the front panel. Remove plug in gas pressure test tap and attach a manometer. Turn the shut-off valve ON . Light the pilot light...

Page 10 - OPERATION; GENERAL OPERATIONAL NOTES; OFF

OPERATION GENERAL OPERATIONAL NOTES Carefully read the description of the hotplate operation on the specification sheet. Do NOT use this appliance if it has been submerged in water. Call a qualified technician to examine the appliance and to service or replace any component which has been submerged....

Page 11 - Turn control valves; FIRE AND EXPLOSION HAZARD; Pilot flame may be extinguished if blocked.; Cleaning Instructions; ONT; REAR

WARNING: FIRE HAZARD NEVER attempt to force or repair a stuck control valve. Contact your Authorized Wells Service Agency for repairs. Forced or improperly repaired valves pose the risk of fire and/or explosion. WARNING: FIRE AND EXPLOSION HAZARD If the pilot light should be extinguished, turn off t...

Page 12 - TROUBLESHOOTING; SYMPTOM

TROUBLESHOOTING 10 SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Pilot will not light Gas supply off Check main / unit gas valves Air in lines Turn gas valve on. Attempt to light pilot every 15 sec. Pilot valve not on Turn pilot valve on / adjust Pilot burner holes are plugged Clean pilot burner Front or ...

Page 13 - CLEANING INSTRUCTIONS; PREPARATION; CAUTION

CLEANING INSTRUCTIONS PREPARATION Turn gas shut-off valve OFF before cleaning. Allow hotplate to cool completely before cleaning. FREQUENCY: Daily TOOLS Bristle Brush Clean Cloth or Sponge Mild Detergent Cleaner Formulated for Stainless Steel Warm Water CLEANING Turn gas shut-off valve OFF before cl...

Page 14 - Fig. 7 Hotplate Assembly

CLEANING INSTRUCTIONS (continued) 12 Fig. 7 Hotplate Assembly FRONT BURNERSlides over RIGHTnozzle; hooks intoFRONT slots onpilot support REAR BURNERSlides over LEFTnozzle; hooks intoREAR slots on pilotsupport GRATE ASSEMBLYSets in place aboveburners DRIP TRAYDrops in place exposingtops of burners 1....

Page 15 - CUSTOMER SERVICE DATA; DESCRIPTION; LEGS, PLASTIC 4” Set of 4; Wells Bloomfield, LLC

DESCRIPTION PART NO. CUSTOMER SERVICE DATA please have this information available if calling for service RESTAURANT _____________________________ LOCATION _____________ INSTALLATION DATE ________________________ TECHNICIAN ___________ SERVICE COMPANY ________________________________________________ ...

Page 16 - Genuine Parts; Wells Bloomfield proudly supports CFESA; WELLS BLOOMFIELD, LLC

Genuine Parts Protect - YOU - All - Ways SERVICE TRAINING - QUALITY SERVICE SERVICE TRAINING - QUALITY SERVICE CUSTOMER SATISFACTION CUSTOMER SATISFACTION Commercial Food Equipment Service Association Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association PRINTED IN UN...