Wells 8792 - Manuals

Wells 8792 – Manual in PDF format online.

Manuals:

Manual

Manual Wells 8792

Summary

Page 2 - xi

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1....

Page 3 - TABLE OF CONTENTS; with or without suffix; MODEL; Cord not provided; SPECIFICATIONS

TABLE OF CONTENTS Thank You for purchasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life. This manual contains the information ...

Page 4 - FEATURES AND OPERATING CONTROLS

FEATURES AND OPERATING CONTROLS Fig. 1 Features & Operating Controls 2 625 75873 Owner s M anual G ourmet 1000 Dual Airpo t Brewers

Page 5 - Installation; AGENCY LISTING INFORMATION

PRECAUTIONS AND GENERAL INFORMATION WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. W...

Page 6 - INSTALLATION INSTRUCTIONS; READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION; PLUMBER’S INSTALLATION INSTRUCTIONS; line. Flush water line before connecting to Brewer.; Equipment; Water supply inlet line

INSTALLATION INSTRUCTIONS READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION REFER TO EXPLODED VIEWS PAGES 18 - 21 FOR COMPONENT NAMES/NUMBERS Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the ...

Page 7 - Fig. 2 Water Supply Installation

INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide ...

Page 8 - OPERATION

OPERATION Fig. 4 Brewer Operation Diagram A. START-UP For initial start-up, or if the brewer has not been used for an extended period of time: Be sure spray disks and brew gaskets are properly installed in both brew heads. Be sure the water supply is properly connected and the water supply valve is ...

Page 9 - AUTOMATIC OPERATION; OPEN

OPERATION (continued) 7 WATER HEATER Water temperature is sensed by a thermobulb inserted into the water tank. This temperature signal is fed to the thermostat, which controls line power to the heating element. The setpoint temperature is adjustable at the thermostat. The element is protected from o...

Page 10 - EMPTY

BREWING COFFEE 8 CAUTION: Burn Hazard Exposed surfaces of the brewer, brew chamber and airpot or server may be HOT to the touch, and can cause serious burns. CAUTION: Burn Hazard To avoid splashing or overflowing hot liquids, ALWAYS place an empty airpot or server under the brew chamber before start...

Page 11 - CLEANING INSTRUCTIONS; PROCEDURE: Clean Coffee Brewer; INSIDE

CLEANING INSTRUCTIONS 9 PROCEDURE: Clean Coffee Brewer PRECAUTIONS: Disconnect brewer from electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush 1. Disconnect brewer from electric power. Allow brewer to cool before cleani...

Page 13 - SERVICING INSTRUCTIONS; Fig. 9 Access Panels

SERVICING INSTRUCTIONS Fig. 9 Access Panels ACCESS PANELS TOP PANEL: Remove top panel to access hot water tank, thermostat, heating elements, brew circuit tubing, faucet valve and piping. Top panel is held by two screws at the rear and a retaining lip at the front. FRONT PANEL: Remove front panel to...

Page 14 - TEMPERATURE ADJUSTMENT; Upon completion, remove thermometer and reinstall vent tube.

SERVICING INSTRUCTIONS (continued) 12 TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube out of tank lid and insert a thermometer of known accuracy in vent hole. Reconnect brewer to electrical power. Place an empty container under brew chamber. Ene...

Page 15 - TIMER ADJUSTMENT (AUTOMATIC BREWERS ONLY); REPLACE THERMOSTAT; OFF; REPLACE HEATING ELEMENT

SERVICING INSTRUCTIONS (continued) 13 IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line. IMPORTANT: Before setting assembly into...

Page 16 - REPLACE SOLENOID

SERVICING INSTRUCTIONS (continued) 14 REPLACE SOLENOID Symptom: Automatic brewer will not flow water; or, automatic brewer drips continuously from brew head. NOTE: Wrench p/n 86660 is designed to allow easy removal of the hoses from the plastic solenoid valve. IMPORTANT: Shut-off water and electric ...

Page 17 - REPLACE TIMER ASSEMBLY; Unplug power cord or turn circuit breaker OFF.; REPLACE HOT WATER FAUCET COIL

SERVICING INSTRUCTIONS (continued) 15 IMPORTANT: When replacing water faucet coil, also replace seal gaskets. NOTE: Any abrasion or roughness on the flat end of the seat cup will require replacing the seat cup: Work the seat cup out of the bonnet and off of the end of the stem. Install a new seat cu...

Page 18 - PROCEDURE: Delime the Water Tank

CAUTION - CHEMICAL BURN HAZARD Deliming chemicals are caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qualified and ex-perienced service personnel. IMPORTANT: DO NOT spill...

Page 21 - ELECTRICAL COMPONENTS

ELECTRICAL COMPONENTS ITEM PART NO. DESCRIPTION USED ON 31 8707-55 Brew Switch, Momentary Rocker All 32 8718-31 Ready-To-Brew Light, green All 35 8718-1 Timer All 36t 8552-18 Terminal Strip Left Side Only 45 85753 Solenoid Valve w/ Bypass Right Side Only 85754 Solenoid Valve, Single Left Side Only 5...

Page 22 - PLUMBING COMPONENTS

EXPLODED VIEW & PARTS LIST (continued) PLUMBING COMPONENTS ITEM PART NO. DESCRIPTION USED ON 8 8540-3 Faucet Outlet Tube Assembly Right Side Only 9 8540-4 Formed Inlet Tube Assembly Right Side Only 10 8551-30 1/4“ Male Flare x 1/8” FPT Right Side Only 11 8514-26 Needle Valve (Faucet Shut-Off) Ri...

Page 23 - CABINET COMPONENTS

EXPLODED VIEW & PARTS LIST (continued) CABINET COMPONENTS ITEM PART NO. DESCRIPTION USED ON 33 8543-42 Spray Head Gasket All 34 82727 Spray Disk All 34a 8543-45 Spray Head Retainer All 70 8706-75 Button Plug (Timer) All 71 82159 Cap, Plastic, Lower Support All 72 82162 Leg, Aluminum Black, Right...

Page 24 - WIRING DIAGRAM

WIRING DIAGRAM 22 p/n 74810 625 75873 Owner s M anual G ourmet 1000 Dual Airpo t Brewers

Page 25 - NOTES

NOTES 23 625 75873 Owner s M anual G ourmet 1000 Dual Airpo t Br ewers

Page 26 - Division of Carrier Commercial Refrigeration; for

PRINTED IN UNITED STATES OF AMERICA Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( ) website: www.wellsbloomfield.com for orders only Bloomfield Industries proudly supports CFESA Commercial Food ...