Wells 8752 - Manuals

Wells 8752 – Manual in PDF format online.

Manuals:

Manual

Manual Wells 8752

Summary

Page 2 - xi

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1....

Page 3 - TABLE OF CONTENTS

MODEL STYLE VOLTS WATTS AMPS 1ø POWER SUPPLY CORD 8752 8752KFT Decanter Brewer 5 Warmers 115/230 4000 19.4 None provided Wire directly to circuit 1 TABLE OF CONTENTS SPECIFICATIONS Thank You for purchasing this Bloomfield Industries appliance. Proper installation, professional operation and consiste...

Page 4 - FEATURES AND OPERATING CONTROLS; Fig. 1 Model 8752 Features and Operating Controls

FEATURES AND OPERATING CONTROLS 2 Fig. 1 Model 8752 Features and Operating Controls 605 70 988 Ow ners M a nual Integri ty 5 W D e can te r Brewer

Page 5 - PRECAUTIONS AND GENERAL INFORMATION; Failure to heed this warning can result in electrical shock.; AGENCY LISTING INFORMATION

PRECAUTIONS AND GENERAL INFORMATION 3 WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock....

Page 6 - INSTALLATION; READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION; PLUMBER’S INSTALLATION INSTRUCTIONS; line. Flush water line before connecting to Brewer.

INSTALLATION 4 READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION REFER TO EXPLODED VIEWS FOR COMPONENT NAMES/NUMBERS Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket and Spr...

Page 7 - SHOCK HAZARD; water hammer arrester; ELECTRICIAN’S INSTALLATION INSTRUCTIONS; Fig. 2 Water Supply Installation

INSTALLATION (continued) 5 NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances. WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Elect...

Page 8 - OPERATION

OPERATION Fig. 4 Brewer Operation Diagram START-UP For initial start-up, or if the brewer has not been used for an extended period of time: ♦ Be sure spray disk and brew gasket are properly installed in the brew head. ♦ Be sure the water supply is properly connected and the water supply valve is tur...

Page 9 - WATER FLOW; AUTOMATIC OPERATION; OPEN

OPERATION (continued) Water temperature is sensed by a thermobulb inserted into the water tank. This temperature signal is fed to the thermostat, which controls line power to the heating element. The setpoint temperature is adjustable at the thermostat. The element is protected from over-temperature...

Page 10 - BREWING COFFEE; BURN HAZARD; Any IntegrityTM brewer can be used in the pour-over mode.; C. AUTOMATIC OPERATION; EMPTY

BREWING COFFEE CAUTION: BURN HAZARD Exposed surfaces of the brewer, brew chamber and decanter may be HOT to the touch, and can cause serious burns. CAUTION: BURN HAZARD To avoid splashing or overflowing hot liquids, ALWAYS place an empty decanter under the brew chamber before starting the brew cycle...

Page 11 - Remove and empty decanters.

CLEANING INSTRUCTIONS PROCEDURE: Clean Coffee Brewer PRECAUTIONS: Disconnect brewer from electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush, Bottle Brush 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning...

Page 13 - SERVICING INSTRUCTIONS

SERVICING INSTRUCTIONS CAUTION: SHOCK HAZARD Opening access panels or removing warmer plates on this brew may expose uninsulated electrical components. Disconnect brewer from electrical power before removing any panel. ACCESS PANELS TOP PANEL: Remove top panel to access hot water tank, thermostat, h...

Page 14 - TEMPERATURE ADJUSTMENT; Fig. 10 Checking and Adjusting Brew Temperature; TEM

SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube out of tank lid and insert a thermometer of known accuracy in hole. Reconnect brewer to electrical power. Place empty container under brew chamber. Energize brewe...

Page 15 - TIMER ADJUSTMENT; REPLACE THERMOSTAT; OFF; REPLACE HEATING ELEMENT

SERVICING INSTRUCTIONS (continued) 13 IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line. IMPORTANT: Before setting assembly into...

Page 17 - REPLACE TIMER ASSEMBLY; Unplug power cord or turn circuit breaker OFF.; REPLACE HOT WATER FAUCET COIL; When replacing

REPLACE TIMER ASSEMBLY Unplug power cord or turn circuit breaker OFF. Remove front panel. Remove knob and three screws holding timer to bracket. Disconnect wiring to timer. Reassemble in reverse order. Adjust timer as described on page 13 REPLACE HOT WATER FAUCET COIL Symptom: Brewer drips continuou...

Page 18 - Repeat steps 4 thru 5; PROCEDURE: Delime the Water Tank

CAUTION: CHEMICAL BURN HAZARD Deliming chemicals may be caustic. Wear appropriate protective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mouth. This operation should only be performed by qualified and experienced service personnel. IMPORTANT: DO NOT spil...

Page 19 - Reinstall wiring to heating element and thermostat.

7. Set the tank back into the brewer. Reassemble the tank lid to the water tank. Make sure the gasket is properly in place, then reinstall lid clamps. 8. Reinstall wiring to heating element and thermostat. Reassemble piping for the faucet. Verify that all internal components are dry, then reinstall ...

Page 20 - EXPLODED VIEW & PARTS LIST

EXPLODED VIEW & PARTS LIST 18 CABINET ASSEMBLY ITEM PART NUMBER DESCRIPTION 1 8700-16 PLATE, WARMER COVER 4 8543-80 CLIP, MOUNTING 23 BUSHING, HEYCO 1/78 33 8543-42 GASKET, SPRAYHEAD 34 82727 SPRAY DISK, EMBOSSED 34a 8543-85 RETAINER, SPRAY DISK (DRILL & RIVET REQUIRED TO INSTALL) 35 85089 D...

Page 22 - HOT WATER TANK ASSEMBLY

EXPLODED VIEW & PARTS LIST 20 HOT WATER TANK ASSEMBLY ITEM PART NUMBER DESCRIPTION 13 8043-5 HOLD-DOWN STRAP 14 8942-92 NUT 8-32 HEX KEPS 50 86280 THERMOSTAT 199ºF 54 8043-12 GASKET, TANK COVER 55 8043-28 NUT, HEX 1/2-20 BRASS 56 8043-30 GASKET, SEAL 57 8941-21 NUT, HEX 7/16-20 BRASS 58 8540-6 H...

Page 23 - PLUMBING COMPONENTS

EXPLODED VIEW & PARTS LIST (continued) 21 PLUMBING COMPONENTS ITEM PART NUMBER DESCRIPTION 8 8540-3 ASSEMBLY, FORMED TUBE FAUCET SUPPLY 9 86904 TUBE, FORMED ASSEMBLY 1/4FF x 1/4 FF 10 80154 FITTING, UNION 1/4MF x 1/4MF 12* 82556 ASSEMBLY, FAUCET 24 8043-26 TUBE, BREW OUTLET METAL 25 8043-13 ELBO...

Page 24 - SERVICE KITS

EXPLODED VIEW & PARTS LIST (continued) 22 SERVICE KITS FAUCET REPAIR KITS 82573 Handle (item 12a) 82575 Seat Cup (item 12c) 82576 Faucet Repair Kit (Includes 12a Handle, 12c Seat Cup, 12d Spring, 12h Stem, 12j Pin & 12k Bonnet 82682 Retainer Clip (item 12b) 84804 Aerator Replacement Kit (Inc...

Page 25 - WIRING DIAGRAM

WIRING DIAGRAM 23 605 7098 8 O w n e rs M anua l Int e gri ty 5 W Decan ter Brew er

Page 26 - Division of Carrier Commercial Refrigeration; for

PRINTED IN UNITED STATES OF AMERICA Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( ) website: www.wellsbloomfield.com for orders only Bloomfield Industries proudly supports CFESA Commercial Food ...