Wells 2080 - Manuals

Wells 2080 – Manual in PDF format online.

Manuals:

Manual

Manual Wells 2080

Summary

Page 2 - xi

NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1....

Page 3 - MODEL; Thermal

TABLE OF CONTENTS SPECIFICATIONS Thank You for purchasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life. This manual contains t...

Page 4 - FEATURES AND OPERATING CONTROLS

Page 5 - DO NOT plug in or; PRECAUTIONS AND GENERAL INFORMATION

WARNING: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING: Injury Hazard All installati...

Page 6 - INSTALLATION INSTRUCTIONS; READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION; UNPACKING & INITIAL INSPECTION; Brewer should be connected to a; WATER; line. Flush water line before connecting to brewer.; Equipment; Water supply inlet line

INSTALLATION INSTRUCTIONS READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION UNPACKING & INITIAL INSPECTION 1. Unpack the unit. Inspect all components for completeness and condition. Ensure that all packing materials have been removed from the unit. 2. (See page 13) Verify that the Spray Head ...

Page 7 - water hammer; in the incoming line, between the backflow; ELECTRICIAN’S INSTALLATION INSTRUCTIONS; listed under UL file E9253.; AGENCY LISTING INFORMATION

INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide ...

Page 8 - OPERATION; Energizing the Brewer:; OPERATING INSTRUCTIONS

OPERATION IMPORTANT: All E-Max™ brewers are tested and set at the factory. If programming adjust-ments are necessary, refer to the E-Max™ Programming Manual (p/n/73674). To over-ride the Brew Wait mode , press and hold the BREW key for 3 seconds when the brewer is in Brew Wait mode (i.e. when brew l...

Page 9 - USER’S GUIDE; Brew complete

OPERATION (continued) WARNING: Burn Hazard. This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from contact with dispensed liquids. CAUTION: Burn Hazard To avoid splashing or overflowing hot liquids, ALWAYS use an empty airpot or thermal server before starting th...

Page 10 - PROGRAMMING FEATURES AND OPTIONS; E-MaxTM Programming Manual

PROGRAMMING FEATURES AND OPTIONS 1. View Water Temperature in Tank: To view the water temperature on the screen, the E-Max™ brewer must be ON, and not brewing or in the filling mode. Press and hold the 4th key, and depress the 6th key. The actual water temperature will be displayed for 3 seconds. 2....

Page 11 - Countdown Quality TimerTM:

8. Clock A. Time – Battery Backup. The E-Max™ has a battery backup system which will maintain the proper time during power failures, or when the brewer is unplugged (even for very prolonged periods of time). Normally there will not be a need to set the time except for Daylight Saving Time changes, o...

Page 13 - Remove airpot or thermal server.

CLEANING INSTRUCTIONS PROCEDURE: Clean Coffee Brewer PRECAUTIONS: Disconnect brewer from electric power. Allow brewer to cool. FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning. 2. Remove ai...

Page 14 - FUNCTION; The solenoid has an internal strainer. To clean the; SERVICING INSTRUCTIONS — PLUMBING

FUNCTION 1. Water enters at the inlet fitting of the fill solenoid (32). The solenoid admits water via a command from the controller. NOTE: The solenoid has an internal strainer. To clean the strainer: Shut off water supply. Unscrew the plastic cap protruding from the rear of the brewer. Remove the ...

Page 15 - SERVICING INSTRUCTIONS — PLUMBING (continued); ITEM

SERVICING INSTRUCTIONS — PLUMBING (continued) ITEM DESCRIPTION PART N0. USED ON 1 2 ASSEMBLY, WATER TANK (120V) 83500 2012, 2072 2015, 2075 6 GASKET, TANK LID 83499 ALL 9 TANK LID 83504 ALL 10 RETAINING CLIP, TANK LID 83506 ALL 11 HOSE, OVERFLOW (2 pc SILICONE 4.5” LONG) 86014 ALL 12 HOSE, FAUCET SU...

Page 16 - SERVICING INSTRUCTIONS - ELECTRICAL; ON

SERVICING INSTRUCTIONS - ELECTRICAL FUNCTION 1. Pressing the POWER key energizes the unit. The POWER LED will glow whenever the unit is ON . 2. Automatic fill is accomplished via a FILL SOLENOID (32) and a WATER LEVEL PROBE (7). The probe senses ground through the water in the tank. When the water l...

Page 18 - SERVICING INSTRUCTIONS — DE-LIMING HEATER TANK; Disconnect brewer form the electrical supply. Turn off

SERVICING INSTRUCTIONS — DE-LIMING HEATER TANK 1. Disconnect brewer form the electrical supply. Turn off the water supply and disconnect water supply from the brewer inlet fitting. 2. Remove the top panel or top warmer section to gain access to internal components. 3. Disconnect water level sensor a...

Page 19 - TROUBLESHOOTING SUGGESTIONS; Using the CANCEL button will not

TROUBLESHOOTING SUGGESTIONS If the E-Max™ goes into the error diagnostic mode as outlined below, it will likely be necessary to reset the brewer in order to test individual components. Note the reset procedure below: * For the first four error modes, press and hold CANCEL for 3 seconds, or RE-ENERGI...

Page 20 - EXPLODED VIEW & PARTS LIST; AIRPOT BREWER

EXPLODED VIEW & PARTS LIST 18 AIRPOT BREWER MODELS: 2082, 2083, 2088

Page 22 - THERMAL BREWER

EXPLODED VIEW & PARTS LIST (continued) 20 THERMAL BREWER MODELS: 2080, 2085, 2086

Page 24 - WIRING DIAGRAMS

WIRING DIAGRAMS MODEL 2080 & 2082 120 VOLT BREWERS AIRPOT and THERMAL 22 White #8 White #9 White #11 Red #3 Black #7 Black #6 Brown #1 Orange/Black #4 Orange/Black #5 Red #3Brown #1Blue #2 Blue #2 Black #6 White #9White #10White #8 14 ga. 1 4 g a . 1 4 g a . 1 4 g a . Tank Heater120 Volt1200 Wat...

Page 27 - NOTES

Page 28 - Division of Carrier Commercial Refrigeration; for

PRINTED IN UNITED STATES OF AMERICA Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( ) website: www.wellsbloomfield.com for orders only Bloomfield Industries proudly supports CFESA Commercial Food ...