Welch Allyn 2380 - Manuals

Welch Allyn 2380 – Manual in PDF format online.

Manuals:

Manual

Manual Welch Allyn 2380

Summary

Page 2 - Disclaimer; Welch Allyn; NOTES

Disclaimer Welch Allyn  reserves the right to make changes in specifications and other information contained in this document without prior notice, and thereader should in all cases consult Welch Allyn to determine whether anysuch changes have been made. The information in this publication doesnot ...

Page 3 - STATUS; CHECK; SHOW FIRMWARE REVISION LEVEL

STATUS CHECK SCANTEAM 2380/PM Programming Menu 3 Scan the bar code below to display the revision level of the SCANTEAM 2380 firmware. SHOW FIRMWARE REVISION LEVEL Scan the bar code below to display the SCANTEAM 2380 software number. The resultinginformation will show if there is a special or custom ...

Page 4 - USER’S

Page 5 - SYSTEM; GUIDE

SYSTEM GUIDE USE THIS PAGE As a general overview of the programming menu. The programming menu consists of two basic components asshown below. MENU PAGE FACING (Not Shown) MENU PAGE BAR CODE DATA CHART Each menu page represents one section of the programming menu. Use individual menu pages in combin...

Page 6 - TERMINAL; SELECTION; DIRECT CONNECT ENABLE; only with a terminal ID of 03.; LOW POWER

TERMINAL SCANTEAM 2380 Information and Examples SELECTION 6 DIRECT CONNECT ENABLE When enabled, this programming selection allows the wand scanner to replace thekeyboard. The scanner will respond the the PC keyboard initialization commands uponpower up. This selection is for an AT keyboard only with...

Page 8 - OUTPUT PARAMETERS

OUTPUT PARAMETERS SCANTEAM 2380 Information and Examples & FORMAT SELECTIONS PREAMBLE/POSTAMBLE Preambles and Postambles are characters added by the 2380 to scanned bar code data. These characters are sent with thebar code data to the terminal. Use the Hex–ASCII table below to find the alpha–num...

Page 12 - SCANCODE; K2 SCANCODE CAPABILITY

SCANCODE SCANTEAM 2380 Information and Examples SELECTION When “main keyboard numbers” is selected, numbers will be sent to the host terminal as ifkeyed in from the main keyboard. If “numeric keypad” is enabled, numbers will be sent as ifkeyed in from the numeric keypad. When programmed on, beeps th...

Page 14 - SYMBOLOGY SELECTION; INDUSTRIAL; INDUSTRIAL CODE OUTPUT FORMATS; FULL ASCII CODE 3 OF 9 CHART; FULL ASCII CODE 3 OF 9 CHARACTERS

SCANTEAM 2380 Information and Examples SYMBOLOGY SELECTION INDUSTRIAL INDUSTRIAL CODE OUTPUT FORMATS FULL ASCII CODE 3 OF 9 CHART NUL SOHSTXETXEOTENQACKBELBSHTLFVTFFCRSOSI %U$A$B$C$D$E$F$G$H$I$J$K$L$M$N$O DLEDC1DC2DC3DC4NAKSYNETBCANEMSUBESCFSGSRSUS $P$Q$R$S$T$U$V$W$X$Y$Z%A%B%C%D%E SPACE/A/B/C/D/E/F/...

Page 15 - SYMBOLOGY

selections variables SYMBOLOGY SELECTION USE THIS PAGE To specify desired bar code symbologies.To select symbology options. CODABAR I II Enable Minimum Length Maximum Length scan scan scan scan *Yes/No *01–MAX Min–48* (CODES) (ID = a) S/S Xmit A B C *Yes/No Notes:(1) * Designates DEFAULT selections....

Page 16 - RETAIL; TOTAL; RETAIL CODE OUTPUT FORMATS; Non–Zero Suppressed UPC–A and UPC–E Output Format

SCANTEAM 2380 Information and Examples SYMBOLOGY SELECTION RETAIL UPC/EAN LENGTH CHART selections Basic W/out W/out # W/2 Digit W/5 Digit Length Ck. Digit Sys. Digit Addendum Addendum UPCA UPCE [w/ 0’s suppressed] UPCE [expanded] UPCD1 UPCD2 UPCD3 UPCD4 UPCD5 EAN8 EAN13 12 8 12 14 20 24 28 32 8 13 –...

Page 19 - IBM XT Keyboard; KEYBOARD LAYOUTS; Continued

A2 A3 A4 A5 A6 A7 A8 A9 B0 D7 D8 D1 C9 A0 D6 A0 IBM PC/AT Keyboard C0 C3 B8 B5 B2 B7 B4 B1 B9 B6 B3 C1 B5 C0 A1 A2 A3 A4 A5 A6 A7 A8 A9 B0 C7 C8 C5 C9 A0 C6 A0 C3 B8 B5 B2 B7 B4 B1 B9 B6 B3 C1 IBM PS2–30 Keyboard B5 C4 C6 A0 IBM XT Keyboard A4 A6 A8 A3 A5 A7 B0 A9 A2 A1 C5 B7 B4 B1 B8 B5 B2 B9 B6 B3...

Page 21 - SAMPLE BAR CODES

SCANTEAM 2380 Programming Menu This page contains bar code symbols in some of the most commonly used symbologies. You may use these codesto test that your system is properly programmed for a particular symbology. SAMPLE BAR CODES UPC–A 0–3132312078–6 UPC–A 0–3132312078–6 5 add on 56098 EAN–13 97–803...

Page 24 - ROMAN NUMERALS

USE THIS PAGE In combination with the adjoining menu pages to program the 2380. SCANTEAM 2380 Programming Menu BAR CODE CHART The bar codes on this page correspond to symbols in shaded areas on adjoining menu pages. SCAN these barcodes in the sequence indicated on menu page to program desired select...

Page 25 - FUNCTION RECORD CODES; CODE 3 OF 9 SYMBOLS

USE THIS PAGE For transmitting functions using function record codes. SCANTEAM 2380 Programming Menu FUNCTION RECORD CODES CODE 3 OF 9 SYMBOLS /C00 /C01 /C02 /C03 /C04 /C05 /C06 /C07 /C08 /C09 /C10 /C11 /C12 /C13 /C14 /C15 /C16 /C17 /C18 /C19 /C20 /C22 /C23 /C24 /C25 /C26 /C27 /C28 /C29 /C30 /C31 /C...