VTech IS7121/IS7121-2/IS7121-22 - Manuals

Page 2 - Basic steps to install your doorbell; Install doorbell battery; Parts checklist; Doorbell overview

Basic steps to install your doorbell Install doorbell battery Doorbell power adapter installation 3 Add and register a doorbell 4 Doorbell location testing 5 Doorbell wall mount installation Parts checklist Your telephone package contains the following items. Save your sales receipt and original pac...

Page 3 - Doorbell power adapter installation; Loosen the screws and the metallic plates, then slide the

3 Doorbell power adapter installation Loosen the screws and the metallic plates, then slide the metal part of the wires underneath the metallic plates as shown. Twist the screws to secure. 1. Wire with red end Wire with black end Screws Metallic plate Metallic plate Install doorbell battery The door...

Page 4 - Add and register a doorbell; light flashes slowly. The doorbell light turns; To deregister all handsets and doorbells:; light is still flashing. The

4 3 Add and register a doorbell You can add another new doorbell (purchased separately) to your IS7121 telephone system. This telephone system accommodates up to two doorbells.Each new doorbell must be paired to the telephone base before use. Press and hold /FIND HANDSET on the telephone base for ab...

Page 5 - You may unplug the AC power first so that you can move around; To test the location for installation:; Settings; flashes; Doorbell location testing

5 Before mounting the doorbell on a wall, make sure you test if the location you install the doorbell is in range, and adjust the camera angle to best suit your needs. You may unplug the AC power first so that you can move around more conveniently to make the tests. To test the location for installa...

Page 6 - To adjust the camera angle:; OK; CAUTION; View; View

6 To adjust the shooting area, you may either relocate the doorbell in different height level, or adjust the camera angle (see below). To adjust the camera angle: Tilt the lever to adjust the angle of the camera lens. The camera lens can be adjusted to left, right or down, up to 0 degrees. After you...

Page 7 - Doorbell wall mount installation; Make sure you have done Step 4 above before you; If you drill the holes into a stud, go to Step 3.

Use the two holes on the doorbell wall mount cover to mark the desirable installation location on the wall. 1. 5 Doorbell wall mount installation Make sure you have done Step 4 above before you mount the doorbell on the wall. If you drill the holes into a stud, go to Step 3. -OR- If you drill the ho...

Page 8 - Align the wall mount cover and screws with the holes in; Align; Loosen the screws and the metallic plates to release the; Open a hole

8 Align the wall mount cover and screws with the holes in the wall (or stud). 3. Align Loosen the screws and the metallic plates to release the wires from the doorbell. Use a sharp object to open a hole on the soft plastic part on the doorbell wall mount cover, then route the power adapter cord thro...

Page 10 - Tighten the screw into the threaded socket at the bottom

0 Tighten the screw Tighten the screw into the threaded socket at the bottom to secure. 8. Plug the adapter into the indoor domestic power supply. 9. Plug!

Page 11 - Detach doorbell from wall mount cover

After an extended exposure to cold, heat or humidity, the doorbell gasket rubber may become sticky.If you need to remove the doorbell from its wall mount cover in case of battery replacement or doorbell relocation, follow the steps below. Remove the screw at the bottom. Insert a flat -bladed screwdr...

Page 12 - Transformer; Installing the doorbell with an existing wired; wired doorbell

If you already have a wired doorbell installed, follow the instructions below to install your new IS741 doorbell unit. Turn off the power supply to the existing wired doorbell.Follow Step through Step 6 in Doorbell wall mount installation from pages to 0. Insert a cross-head screwdriver to the side ...

Page 13 - Important safety instructions; Ring the rear doorbell of the existing wired doorbell; Doorbell wall mount; on pages and 0 to complete the installation.; If you do not connect domestic power supply nor

3 Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: Read and understand all instructions.Follow all warnings and instructions marked on the product. Unp...

Page 14 - Precautions for users of implanted cardiac pacemakers; Operating range; Limited warranty

4 Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones):Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted ...

Page 15 - Please retain your original sales receipt as proof of purchase.; FCC, ACTA and IC regulations

5 How long is the limited warranty period? The limited warranty period for the Product extends for ONE () YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replac...

Page 16 - Technical specifications

6 FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AA...