Vermont Casting SHR48 - Manuals

5 SHR Series Woodburning Fireplaces 20001384 FP554A SH Series 1/28/99 djt Chase Installation Insulation methods shown are optional for cold climate, not a requirement for unit operation. FP554A Fig. 5 Fireplace and chase parts identification. (SHR48 shown) Termination Cap Storm Collar Pan Flashing Ba...

6 SHR Series Woodburning Fireplace 20001384 Chimney Requirements - Offset Installations 0 0 0 0 0 3" 11" 1 0 0 0 0 8 ¹⁄₄ " 20" 0 1 0 0 0 11 ¹⁄₄ " 25 ¹⁄₄ " 2 0 0 0 0 13 ¹⁄₂ " 29 ¹⁄₄ " 1 1 0 0 0 16 ¹⁄₂ " 34 ¹⁄₄ " 0 0 1 0 0 20 ¹⁄₄ " 40 ³⁄₄ " 2 1 0 0 0 21 ...

7 SHR Series Woodburning Fireplaces 20001384 Planning Information The Ten Foot Rule Major U.S. building codes specify a minimum chimney height above the roof top. The “Ten Foot Rule” is a fire safety rule and not a draft rule. To ensure proper draft, it is recommended that you always meet or exceed t...

8 SHR Series Woodburning Fireplace 20001384 Installation Chimney Supports The chimney system is supported by the fireplace for vertical chimney heights less than 30 feet above the hearth. Chimney supports are required if the vertical height exceeds 30 feet with 11CF chimneys. Locate chimney supports ...

9 SHR Series Woodburning Fireplaces 20001384 Framing Framing can be constructed before or after the fireplace is set in place, however, most installers build the frame before setting the fireplace.Frame fireplace with 2 x 4 lumber or heavier materials. Refer to framing dimensions in Figures 1 - 4 for b...

10 SHR Series Woodburning Fireplace 20001384 FP556SHR Fig. 13 Locate centerline of chimney with plumb line. FP556SHR SHR LOCATE CENTER LINE 5/11/99 djt Chimney Centerline Actual Centerpoint Plumb Line Plumb Bob Imaginary Centerpoint 11 ¹⁄₈ " (283 mm) FP 548b SHR 5/11/99 djt Angle of Chimney at C...

11 SHR Series Woodburning Fireplaces 20001384 The inside dimension of the frame must be the same as the hole size selected from Figure 11 in order to provide the required 2 inches of air space between the outside diameter of the chimney and the edges of the framed ceiling hole. Positioning, Safety S...

12 SHR Series Woodburning Fireplace 20001384 Installing the Chimney System Start by attaching the first chimney section to the collar on top of the fireplace. Install the pipe as pictured in Figure 19. When you get a good lock, you will hear the pipe clearly snap together. Once sections are snap-locke...

13 SHR Series Woodburning Fireplaces 20001384 Attic Installation Ceiling Installation Fig. 21 Installing firestop spacer. FP285 IWF285 mbuf 5/25/96 Nails (4) Firestop Spacer Joist Joist Firestop Spacer Nails (4) Flange Down Into Hole Flange Up Into Hole Continue Installing Pipe to Complete Run Contin...

14 SHR Series Woodburning Fireplace 20001384 Installing Chimney in a Chase Refer to Page 5, Figure 4 for an illustration of a typical chase installation. CAUTION: Treatment of firestop spacers and construc- tion of chase may vary with type of building. These instructions are not a substitute for loca...

15 SHR Series Woodburning Fireplaces 20001384 FP1166surround flushwith finished wall12/20/01 djt Stud 2 x 4 Header Ledge Bracket Surround Must be Sealed with Noncombustible Material Noncombus- tible Decorative Facing Finished Wall FP1166 Fig. 25 Fireplace surround flush with finished wall. FP1277 SHR5...

17 SHR Series Woodburning Fireplaces 20001384 Side Wall Protection Adjacent combustible side walls that are within dimen-sions shown in Figure 29 of fireplace opening must be protected with Wall Shield Model SP40 or a specifically built wall shield described in Figure 28.The special wall shield design...

18 SHR Series Woodburning Fireplace 20001384 FP532SHR Fig. 31 Combustible side wall protection and hearth extension dimensions. Minimum Wall Clearances WITH Noncombustible Surround Facing WITHOUT Noncombustible Surround Facing Minimum Hearth Extension Dimensions (for On-Site Construction) G H G J Se...

19 SHR Series Woodburning Fireplaces 20001384 removed from gas line tube to repack space around the pipe. Material should be inserted from outside of the fireplace and packed tightly to totally seal between the pipe and tube. Note: Gas pipe should not come in contact with any wood structures until it...

20 SHR Series Woodburning Fireplace 20001384 1384 pts replacement parts 5/27/99 djt 7/14/99 removed clips,added push nut 1 2 3 4 5 6 7 8 a b c 9 10 11 d 12 13 CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any tim...

21 SHR Series Woodburning Fireplaces 20001384 Description Designed to enclose the fireplace opening with glass doors allowing the fire to remain visible. Available in Polished, Brushed Brass, Black and Pewter Provides outside air for fuel conbustion in the firebox. This accessory must be installed befo...

22 SHR Series Woodburning Fireplace 20001384 Accessory Description Model No. Contemporary Flashing Contemporary Chase Top Termina-tion Contemporary Round Top Termina-tion Extended Round Top Chimney Sections Chimney Elbows Top Housing withUpper Baffle Attic Insulation Shield Required for contemporary ...

23 SHR Series Woodburning Fireplaces 20001384 � LIMITED WARRANTY & 30 YEAR PROTECTION PLAN For MAJESTIC FIREPLACES ® PRE-ENGINEERED Fireplace Systems CFM Corporation warrants its MAJESTIC FIREPLACES® Pre-En-gineered Fireplace (“Fireplace”) and the CFM Corporation supplied firegrate, glass doors, ...