Vermont Casting DVRSL - Manuals

- 6 - 1/2" GAS SUPPLY 1/2" X 3/8" REDUCER 3/8" NIPPLE 3/8" NIPPLE 3/8" NIPPLE 3/8" X 3/8" SHUT OFF VALVE 3/8" UNION When using copper or flex connector use only approvedfittings. When using black iron pipe always provide aunion so that gas line can be easily disco...

- 7 - , ,, , V V V V V V V V V X X ,, , X D E B B B C B M B A J K A F L G G TERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA(TERMINATION PROHIBITED) H I Fixed Closed Fixed Closed Openable Openable Fixed Closed G G N N GENERAL VENTING Your fireplace is approved to be vented either throughth...

- 8 - ,, ,, , , Outside Corner Inside Corner Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. A =Combustible 6"(152mm) Noncombustible 2"(50mm) B =Combustible 6"(152mm) Noncombustible 2"(50mm) , A ,, ,, Balcony - with no side w...

- 9 - *IMPORTANT* Minimum clearance between vent pipesand combustible materials is one (1") inch (25 mm) on bottom, sides and top. Join pipes and secure joints with three (3) sheetmetalscrews. (See Fig. 9) Wipe off excess sealant. GENERAL INFORMATION ON ASSEMBLING THE VENT PIPES WITH CRIMPED END...

- 10 - The maximum horizontal vent run is 20 feet (6100mm)when the vertical vent rise is 7.5 feet (2286mm). Fig. 14 Since it is very important that the venting systemmaintain its balance between the combustion air intakeand the flue gas exhaust, certain limitations as to ventconfigurations apply and...

- 11 - Fig. 17 For each 45 degree elbow installed in thehorizontal run (while maintaining a constanthorizontal plane), the length of the horizontalrun MUST be reduced by 18" (457mm). Thisdoes not apply if the 45 degree elbows areinstalled on the vertical part of the ventsystem. If a 90 degree el...

- 12 - Fig. 19 COMBUSTIBLE WALLS (Fig. 19): Cut a 9-3/8"H x 9-3/8"W (240mm x 240 mm) hole through the exterior wall and frame as shown NON-COMBUSTIBLE WALLS (Fig. 19): Hole opening must be 7.5" (190 mm) in diameter. (240mm) 9- 3/8 " 9- 3/8 " (240mm) 7- 1/2 " (190mm) Vent Open...

- 13 - Fig. 21 Fig. 20 STEP 4 (Fig. 22) Measure the horizontal length requirementincluding a 2" (50mm)overlap, i.e. from the elbow to theoutside wall finish plus 2" (or the distance required ifinstalling a second 90º elbow). STEP 3 (Fig. 21) Apply a bead of high temperature sealant to theinn...

- 14 - STEP 7 Support the horizontal pipes every 36 inches (914mm) withmetal pipe straps. Make sure that the horizontal vent pipeis installed on a level horizontal plane. STEP 8 Recheck the fireplace to make sure that it is levelled,properly positioned, and nailed or screwed to the floor. If applied...

- 15 - FOUNDATION RECESS SNORKEL SCREWS WALL SCREWS SHEET METAL WATERTIGHT SEAL AROUND PIPE If the foundation is recessed, use recess brackets (notsupplied) for securing lower portion of the snorkel. Fastenbrackets to wall first and then secure to snorkel with selfdrilling #8 x 1/2 sheet metal screw...

- 16 - Fig. 34 1. Locate your fireplace. 2. Plumb to centre of the (4") 90º transition elbow(7DVRT90) from ceiling above and mark position. 3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240mm). 4. Proceed to plumb for additional openings through theroof. In all cases, the opening mus...

- 17 - DVR SERIES CRIMPED VENTING COMPONENTS 7DVRVT - Through the wall Rear Vent Termination Starter Kit -Model 7DVSK - Sidewall Venting Starter Kit - Model 7DVSKV - Vertical Venting for 7DVSKV-A order 1/12 to 6/12 roof pitchfor 7DVSKV-B order 7/12 to 12/12 roof pitchfor 7DVSKV-F order flat roof Sta...

- 18 - GENERAL INFORMATION ON ASSEMBLING THE TWIST LOCK VENT PIPES When using CFM Majestic twist lock pipe it is not neces-sary to use silicone to seal the twist lock joints. The onlyareas that need silicone are the collars on the fireplace,the telescoping pipe (if used) and the horizontal termina-t...

- 19 - Fig. 37 Combustible Walls. Cut a 10-3/8"H x 9-3/8"W (265mmx 240mm) hole through the exterior wall and frame asshown. Fig. 37. Non-Combustible Walls: Hole opening must be 7.5"(190mm) in diameter. To locate hole centre consult withappropriate fireplace specifications, page 4. (240mm...

- 20 - The maximum horizontal vent run is 20 feet (6100mm)when the vertical vent rise is 7.5 feet (2286mm). Fig. 41 Fig. 41 VERTICAL SIDEWALL INSTALLATIONS Since it is very important that the venting systemmaintain its balance between the combustion air intakeand the flue gas exhaust, certain limita...

- 21 - INSERT Fig. 44 The maximum number of elbow degrees in a system is270 o . (This does not include transition elbow from rear vent to vertical vent.) Fig. 44 Sample: 1 - 90 o 2 - 45 o 3 - 45 o 4 - 90 o Total - 270 o 90" 2286mm 120" 3048mm 84" 2134mm 90 o elbow=3' Fig. 43 SEE PAGE 23 ...

- 22 - VENT SIDEWALL INSTALLATION *IMPORTANT* Minimum clearance between vent pipesand combustible materials is one (1") inch (25 mm) onbottom, sides and top. Vent Starter Kit 7TDVSK, plus TransitionE l b o w 7 T D V R T 9 0 m u s t b e u s e d i nVertical Sidewall installations. The 4" pipe ...

- 26 - 7DVRVT - Through the wall Rear Vent Termination Starter Kit -Model 7TDVSK - Sidewall Venting Starter Kit - Model 7TDVSKV - Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitchfor 7TDVSKV-B order 7/12 to 12/12 roof pitchfor 7TDVSKV-F order flat roof Starter Kit - Model 7TDVSKS -Snorkel...

- 27 - SIDE GLASS REMOVAL 1. Shut off gas. 2. Let the fireplace cool if it has been operating. 3. Remove side top louvre. (See Louvre Removal) 4. Open the side lower louvre assembly. 5. Release the two clamps at the bottom of the windowframe by pulling down on the clamp handles. 6. Lift off the glas...

- 29 - INSTALLATION OF LOGS Left and right side are defined using themanifold as reference. Facing themanifold,the left side is on your left and theright side is on your right. Fig. 69 Fig. 70 Top logs must be placed properly onton o t c h e s LAVA ROCK The lava rock provided with this fireplace mus...

- 30 - 4. Push in gas control knob slightlyand turn clockwise to "OFF". Do not force. 5. Close control access panel. C. Use only your hand to push in or turn the gas controlknob. Never use tools. If the knob will not push in or turnby hand, do not try to repair it, call a qualified servicete...

- 31 - TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT 820 NOVA MILLIVOLT VALVE START CHECK GLASS DOOR TO BE REMOVED BEFORE SERVICE WORK GAS SUPPLY ON • SHUTOFF VALVE OPEN• CONFIRM GAS HOOK-UP LIGHT PILOT WITH PIEZO IGNITION • ELECTRODE GAP MIN. 1/8"• ELECTRODE CRACKED• ELECTRODE CABLE ATTACHED• PIE...

- 32 - The burner and control system consists of: • main burners • gas orifices • pilot assembly • thermopile • millivolt gas valve Most of these components may require only an occasionalcheckup and cleaning and some may require adjustment.If repair is necessary, it should be performed by aqualified...

- 34 - REPLACEMENT PARTS LIST - DVRS3/DVRSL/DVRSR D ESCRIPTION P ART N O . DVRS3 DVRSL/DVRSR 1. Log Set Complete 10001271 100001271 1a. Log - Ember Log Set B18 B18 1b. Log - Ember Log Set B19 B19 1c. Log - Rear Pilot Side B20 B20 1d. Log - Rear Front Side B21 B21 1e. Log - Side Front B22 B22 1f. Log...

- 35 - EB1 1. Slide fan assembly from the left side into fireplaceopening, line up mounting holes with screw studs onrear of fireplace and fasten with #10-24 hex nuts. 2. Install thermal sensor on bottom of firebox using#10-24 hex nuts. 3. (Option A) - Place electronic fan speed control boxon bottom...