US Stove Company 1800GC - Manuals

Page 4 - When using a Class A or double wall flue pipe connection,

NOTE: Type of chimney: Class A All-Fuel also referred to asLow-Heat appliance type chimney per Uniform MechanicalCode: Chimney, low-heat appliance type is a factory built, masonryor metal chimney suitable for removing the products ofcombustion from fuel-burning low-heat appliances produc-ing combust...

Page 6 - CUTOUT

EXISTINGFURNACE(if used) HOTBLAST FURNACE HOT AIRPLENUM 2" MIN. 1" MIN. 1" MIN. HOT AIR DUCT MINIMUM CLEARANCES TO COMBUSTIBLES (2.54 cm) 6' (182.88cm) 6' (182.88cm) (5.08 cm) (2.54 cm) CONNECTING HOT AIR DUCT TO FURNACE CONNECTING HOT AIR DUCT TO FURNACE CONNECTING HOT AIR DUCT TO FURNA...

Page 7 - FAN LIMIT KIT; SIDE OF HOTBLAST FURNACE

FUEL DOORILLUSTRATION ASH DOORILLUSTRATION LOCK WASHER HEX NUTS ASSEMBL ASSEMBL ASSEMBL ASSEMBL ASSEMBLY INSTR Y INSTR Y INSTR Y INSTR Y INSTRUCTIONS UCTIONS UCTIONS UCTIONS UCTIONS COMBUSTION AIR COMBUSTION AIR COMBUSTION AIR COMBUSTION AIR COMBUSTION AIR All fires need air (specifically oxygen) to...

Page 8 - Place remaining firebrick in smoke chamber as

BRICK INSTALLATION BRICK INSTALLATION BRICK INSTALLATION BRICK INSTALLATION BRICK INSTALLATION (PRE-INSTALLED AT FACTORY) (PRE-INSTALLED AT FACTORY) (PRE-INSTALLED AT FACTORY) (PRE-INSTALLED AT FACTORY) (PRE-INSTALLED AT FACTORY) NOTE: Prior to operation, be sure to remove brickretaining strips. MOD...

Page 10 - SPIN DRAFT CAP; Screw spin draft and bolt assembly into ash door allowing

SPIN DRAFT CAP 1/2" X 2-1/2"CARRIAGEBOLT 1/2" LOCK NUT INSTALLING ASH DOOR SPIN DRAFT INSTALLING ASH DOOR SPIN DRAFT INSTALLING ASH DOOR SPIN DRAFT INSTALLING ASH DOOR SPIN DRAFT INSTALLING ASH DOOR SPIN DRAFT 1. Screw spin draft onto 1/2" x 2-1/2" carriage bolt. 2. Screw spin dr...

Page 11 - ALL ELECTRICAL WIRING SHOULD BE DONE

WIRING DIAGRAM FOR SERIES INSTALLATION WITH EXISTING ELECTRIC FURNACE BLACK TO BE ADDED BLUE BLACK WHITE BLACK MAIN POWER 110 VOLT BLUE FROM LIMIT BLACK BLACKTO BEADDED HOTBLAST LIMIT CONTROL MUST PULL OUT MUST PULL OUT MUST PULL OUT MUST PULL OUT MUST PULL OUT THE JUMPER THE JUMPER THE JUMPER THE J...

Page 12 - Ra; ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN

WIRING DIAGRAM FOR SERIES INSTALLATION WITH EXISTING GAS OR OIL FURNACE LH POINTER (FAN OFF) 100 CENTER POINTER(FAN ON) 150 RH POINTER (LIMIT OPENS) 200 SAFETY STOP SETTING LIMIT CONTROL 50 150 100 200 250 FAN LIMIT HIGHLIMITCONTROL WALL THERMOSTAT ELECTRICAL BOX DRAFT FAN CENTER R* WIRE INTO GASVAL...

Page 14 - NEVER BURN GREEN WOOD OR TIRES.

! The furnace is designed to burn air dried wood and coal at apredetermined firing rate. Over firing could result in damageto the heat exchanger and cause dangerous operation. Overfiring occurs when the ash door is left open during operationor a highly volatile fuel, i.e. large amounts of small kind...

Page 19 - REAR WALL OF FIREBOX

INST INST INST INST INSTALLA ALLA ALLA ALLA ALLATION OF OPTIONAL EQ TION OF OPTIONAL EQ TION OF OPTIONAL EQ TION OF OPTIONAL EQ TION OF OPTIONAL EQUIPMENT UIPMENT UIPMENT UIPMENT UIPMENT INSTALLING DOMESTIC HOT WATER COIL INSTALLING DOMESTIC HOT WATER COIL INSTALLING DOMESTIC HOT WATER COIL INSTALLI...

Page 20 - UNITED STATES STOVE COMPANY; 27 Industrial Park Road

HO HO HO HO HOW W W W W T T T T TO ORDER REP O ORDER REP O ORDER REP O ORDER REP O ORDER REPAIR P AIR P AIR P AIR P AIR PAR AR AR AR ARTS TS TS TS TS THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THEHEATER, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FO...