US Stove Company 1200Q - Manuals

US Stove Company 1200Q – Manual in PDF format online.

Manuals:

Manual

Manual US Stove Company 1200Q

Summary

Page 2 - TOOLS AND MATERIALS NEEDED; TOOLS

2 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• TOOLS AND MATERIALS NEEDED TOOLS Pencil6 Foot Folding Rule or TapeTin SnipsDrill, Hand or ElectricDrill Bit (For Sheet Metal Screws) 1/8" Dia.Screw Driver (Blade-Type)GlovesSabre Saw5/16" Nut Driver or5/16" Socket with Rachet MATERIALS 6" P...

Page 3 - Your Furnace has the following labels. Read and obey all labels.; REFER TO MARKINGS ON THE APPLIANCE FOR ADDITIONAL INFORMATION.

3 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• CAUTION: Your Furnace has the following labels. Read and obey all labels. REFER TO MARKINGS ON THE APPLIANCE FOR ADDITIONAL INFORMATION. CAUTION! INSPECT FLUE PIPES, FLUE PIPE JOINTS AND FLUE PIPE SEALSREGULARLY TO ENSURE THAT SMOKE AND FLUE GASES ARE NOTD...

Page 4 - RULES FOR SAFE INSTALLATION AND OPERATION

4 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• Read these rules and the instructions carefully. Failure to follow them will cause a hazard that could result indeath, serious bodily injury, and/or property damage. Check your local codes. This installation must comply with their rulings. Do not install t...

Page 5 - HOW THE FURNACE FUNCTIONS

5 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• Your Supplemental Furnace is designed to be a supplemental or central heating source for yourhome. This solid fuel furnace may be installed inconjunction with a properly operating central fur-nace that is listed or certified in accordance withnationally re...

Page 7 - LOCATING THE FURNACE

7 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• 1. 2. 3. 4. FIG. 3 The furnace should be located in the sameroom as the central system and as close aspossible, but no closer than 9". There should beno wall between the furnace and the warm airoutlet duct that is connected directly to thewarm air outl...

Page 8 - CHIMNEY CONNECTION

8 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• LISTED FACTORY BUILT CHIMNEYCarefully follow chimney manufacturer's instructions. Use only a Listed Residential Type or Building HeatingAppliance Chimney. If your chimney starts at the ceiling (Fig. 5), you will need enough 6" pipe to reach the ceiling...

Page 9 - RULES FOR CONNECTOR PIPE INSTALLATION

9 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• RULES FOR CONNECTOR PIPE INSTALLATION FIG. 6 The crimped end of the chimney connectorfits inside the furnace flue collar. Installadditional chimney connector and elbowwith the CRIMPED END TOWARD THEFURNACE. This will allow any con-densation in the flue to ...

Page 10 - ASSEMBLY OF FURNACE

10 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• ASSEMBLY OF FURNACE Your furnace requires the following itemsto be assembled or installed by the serviceperson: Feed Door HandleFeed Door LatchAsh Door HandleAsh Door LatchBlower and Blower ControlElectrical Connections Remove all parts from inside thefur...

Page 12 - MODEL 1200Q WIRING DIAGRAM -; LIMIT CONTROL; x 4 JUNCTION BOX

12 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• MODEL 1200Q WIRING DIAGRAM - FIG. 12 LIMIT CONTROL BLACK WHITE WHITE BLACK WHITE BLACK GREEN 2 x 4 JUNCTION BOX BLOWER TOHOUSESUPPLY NOTE: GROUND HOUSESUPPLY TO INSIDE OFJUNCTION BOX.

Page 13 - Installation

13 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• Installation Please see all methods of Installationin Appendix at the rear of this booklet. This is a furnace, not a free standing stove. You mustdirect heated air from 12" outlet away from the furnace,or it will not function properly. 1. This install...

Page 14 - POWER FAILURE INSTRUCTIONS:; Operation after loss of power

14 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• POWER FAILURE INSTRUCTIONS: Operation after loss of power Remove filter if provided.Do not expect to keep home at normal temperatures.Do not load fuel above bottom of feed door.Set Fuel door and Ash door spin draft maximum closedper the factory installed ...

Page 16 - ALTERNATIVE PARALLEL INSTALLATION WIRING DIAGRAM

16 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• ALTERNATIVE PARALLEL INSTALLATION WIRING DIAGRAM - FIG. 15 TO GAS/OIL/ELECTRIC TRANSFORMER HOTBLAST COMBINATION CONTROL LIMIT FAN JUMPER IN H H POWER SUPPLY GAS/OIL/ELECTRIC POWER SUPPLY JUNCTION BOX CENTRAL FURNACE BLOWER MOTOR WOOD FURNACE BLOWER MOTOR ...

Page 17 - OPERATING INSTRUCTIONS

17 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• Your Hotblast Furnace is for burning wood only. WOOD BURNING: (1)use Hardwood, 18" to 26", split and air dried (seasoned) for six months. (2) set thermostatto "HIGH" before opening feed door. (3) add wood to a convenient level. CAUTION NEV...

Page 18 - SERVICE HINTS; CHIMNEY MAINTENANCE

18 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• Do not expect a furnace to draw. It is the chimney thatcreates the draft. Smoke spillage into the house or exces-sive build-up of water or creosote in the chimney is notfunctioning properly. Correct the problem before usingfurnace. Possible causes are: Th...

Page 21 - APPENDIX; INSTALLATION A; NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED

21 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX INSTALLATION A NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED FOR THIS INSTALLATION.

Page 22 - INSTALLATION B

22 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX INSTALLATION B NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED FOR THIS INSTALLATION.

Page 23 - INSTALLATION C

23 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX INSTALLATION C NOTE: ANTI-BACKDRAFT FLAPPERS OR BAFFLE ARE REQUIRED FOR THIS INSTALLATION.

Page 24 - INSTALLATION D

24 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX INSTALLATION D (U.S. ONLY) INSTALLATION E (U. S. ONLY)

Page 25 - INSTALLATION F

25 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• APPENDIX INSTALLATION F INSTALLATION G

Page 26 - NOTES

Page 27 - TROUBLE SHOOTING TIPS FOR WARM AIR FURNACE

27 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• List of Problems Possible Cause Solutions 1. Smoking when feed door is open. 2. Furnace does not heat. 3. Blower does not run. 4. No air from registers - fan running. 5. Air from registers is not hot. 6. Blower runs too long. 7. Blower does not run long e...

Page 28 - THE PART DESCRIPTION; HOW TO ORDER REPAIR PARTS; UNITED STATES STOVE COMPANY; WARNOCK HERSEY

28 •DRAWINGS FOR ILLUSTRATION PURPOSES ONLY• THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPEND-ABLE SERVICE FROM YOUR HOTBLAST FURNACE, AND EN-ABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFER-ENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBERWHICH IS ON...