Ultra Start 1280 - Manuals - manualsarea.com

Page 2 - INSTALL MANUAL; TABLE OF CONTENTS; Relay Diagrams

SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PAGE 2 PAGE 3 80 SERIES 80 SERIES INSTALL MANUAL INSTALL MANUAL TABLE OF CONTENTS QUICK VIEW WIRE DIAGRAM 1 5 3 2 4 6 1 2 3 4 5 6 7 8 9 10 11 12 13 1 3 2 4 OUTPUT TO ACTIVATE IGNITION CIRCUIT THE VEHICLES SELECTABLE OUTPUT* (DEFAULT 2ND IGN) 12...

Page 4 - THERMISTOR/ INPUT TRIGGER TO START; Position 1 or Position 2; BYPASS MODULE DATA COMMUNICATION PORT; Connect the following wires for manual transmission vehicles:; PARK BRAKE INPUT FOR MANUAL TRANSMISSIONS; Type 4 - Disconnect Switch

SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PAGE 4 PAGE 5 80 SERIES 80 SERIES INSTALL MANUAL INSTALL MANUAL QUICK VIEW WIRE DIAGRAM MANUAL TRANSMISSION MODELS 123 123 1234 THERMISTOR/ INPUT TRIGGER TO START Position 1 or Position 2 BLACK** GREEN** BLUE** GREEN BLUE N/A* RED BLACK WHT/VIO...

Page 6 - Press Lock; *Pause for about 1 second between programming of each remote

SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PAGE 6 PAGE 7 80 SERIES 80 SERIES INSTALL MANUAL INSTALL MANUAL QUICK VIEW PROGRAMMING QUICK VIEW PROGRAMMING Press Lock Press Unlock Press Start Press # MENU 1 MENU 2 MENU 3 MENU 4 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key O...

Page 8 - QUICK VIEW PROGRAMMING; with the key then; BRAKE

SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PAGE 8 PAGE 9 80 SERIES 80 SERIES INSTALL MANUAL INSTALL MANUAL QUICK VIEW PROGRAMMING TACH / TACHLESS LEARNING AUTO TACH/ TACHLESS LEARNING Horn/ Siren will chip to confirm that the Tach/ Tachless has been programmed. Start the vehicle with th...

Page 10 - SYSTEM WIRING DETAILS; Positive Park light Output.; SYSTEM GROUND INPUT; BLUE; CONFIGURATION AND OTHER INFORMATION, PLEASE VISIT

SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 PAGE 10 PAGE 11 80 SERIES 80 SERIES INSTALL MANUAL INSTALL MANUAL SYSTEM WIRING DETAILS SYSTEM WIRING DETAILS PIN-1 YELLOW Starter Output- This wire will test 0V when the key is off, in the Accessory position and when the Ignition is in the on ...

Page 12 - 3 PIN CONNECTOR; (Car Finder and Auxiliary 1 are not available on 2way models); *Connect to door pin for Passive Arming on 1280 and 3285.; SYSTEM PROGRAMMING -

13 PIN CONNECTOR 1-YELLOW Re-arm(-) (Programmable) Supplies one .75 second pulse when locked and one .75 second pulse after remote start shutdown. Factory alarm re-arm/ RAP shutdown. 2-BROWN Dis-arm(-) Supplies one .75 second pulse when the unlock button is pressed and one .75 second pulse before re...

Page 14 - *Pause for about 1 second between programming of each remote.

4 PIN AUXILIARY SENSOR CONNECTOR* FULL TRIGGER INPUT BLACK GROUND OUTPUT FOR AUXILIARY SENSOR GREEN BLUE PRE-WARN TRIGGER RED 12VOLT OUTPUT FOR AUXILIARY SENSOR 1- BLUE Pre-Warn Trigger (-) Input When this wire is grounded by an auxiliary sensor (i.e: Radar Sensor) the system will chirp the SIREN 3 ...

Page 16 - Helps; INSTALL MANUAL; PROGRAM MODE; ENTERING PROGRAM MODE 1; Press and release 1 time; PROGRAM SWITCH; CHIRP; Confirming

SYSTEM PROGRAMMING - Menu 1 SETS OPTION 1 - SHORT PULSES- The output for lock and unlock is .25sec. Helps prevent windows from rolling up/down on some vehicles. . SETS OPTION 2 – LONG PULSES- The output for lock and unlock is 3 seconds. Used to activate vacuum door lock systems. SETS OPTION 3 – NORM...

Page 18 - The alarm will not; IGNITION KEY

SYSTEM PROGRAMMING - Menu 1 PAGE 19 80 SERIES INSTALL MANUAL PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 PAGE 18 80 SERIES INSTALL MANUAL PROGRAM MODE CON'T FROM PREVIOUS PAGE 1 CHIRP 2 CHIRP 3 CHIRP CHANGE SETTING 8 - GOTO SETTING 9 - PRESS & RELEASE THE VALET SWITCH PRESS & HOLD THE VALET SWI...

Page 20 - SIREN CHIRP

SYSTEM PROGRAMMING - Menu 1 PAGE 21 80 SERIES INSTALL MANUAL PROGRAM MODE SYSTEM PROGRAMMING - Menu 1 PAGE 20 80 SERIES INSTALL MANUAL PROGRAM MODE CON'T FROM PREVIOUS PAGE CHANGE SETTING 4 - GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIR...

Page 24 - RELAY DIAGRAMS; USE SPDT 12v Relay; INVERTER; USE SPDT 12v Relay; USE SPDT 12v Relay

DOOR LOCK DIAGRAMS Green Vehicle's Lock/Unlock Switch To Control Relay orActuators N EG A TI VE D O O R L O C K (L O W C U R R EN T) Al ar m a nd / or S ta rte r M od ul e Door lock Output SYSTEM PROGRAMMING - Menu 1 PAGE 25 80 SERIES INSTALL MANUAL RELAY DIAGRAMS SYSTEM PROGRAMMING - Menu 1 PAGE 24...

Page 26 - ALARM MODELS ONLY; QUICK VIEW OPERATIONS; SHOCK SENSOR SETTINGS; QUICK VIEW OPERATION CHART; BUTTON; ** PLEASE SEE OWNERS GUIDE FOR DETAILED OPERATIONS AND FEATURES; SERVICE MODE / EMERGENCY OVERRIDE

ALARM MODELS ONLY 3 CHIRPS Press & HOLD Lock + Unlock buttons at the same time Press & HOLD Lock + Unlock buttons at the same time Each time the lock button is pressed and released the sensitivity will INCREASE by 1 level. This is confirmed by a series of park light flashes & SIREN Chirp...

Page 28 - TRANSMITTER PROGRAMMING; ENTERING REMOTE PROGRAM MODE; If the park lights; RESERVATION MODE

SYSTEM PROGRAMMING - Menu 1 PAGE 29 80 SERIES INSTALL MANUAL MANUAL TRANSMISSION TRANSMITTER PROGRAMMING ENTERING REMOTE PROGRAM MODE The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed together during the same sequence. For security, when a new remote is progra...

Page 30 - If the start; PARK LIGHTS STATUS LED; NOTES

DIAGNOSTICS CHART TO ENTER DIAGNOSTIC MEMORY If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the start button is pressed the park lights flash 3 times slowly. Looking ...