U-Line U-2115RSOD-00 - Manuals

u-line.com 3 Your U-Line product has been designed for either free-standing or built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed and clearance is required for an electrical connection in the...

4 u-line.com 4 Product Dimensions 2115R Series 2115WC / 2115WCOL Series 21175RC/RCG/RF Series 23-1/16" 34-1/8" 24" 2175R(C)(F) Black and White Models 2175R(C)(F)S(G) Stainless & Out Door Models 2175R(C)(F)S Overlay Models 24" 24" 34-1/8" 34-1/8" 3-13/16" 23-1/16&#...

u-line.com 5 34-1/8" 23-15/16" 22-5/8" 34-1/8" 2175BEVCS Stainless Steel Models 2175BEVCOL Wood Overlay Models 23-1/4" 3-13/16" 23-15/16" 3-13/16" 34-1/8" 24" 22-5/8" 34-1/8" 24" 2175WCCS Stainless Steel Models 2175WCCOL Wood Overlay Models 23-1/4&...

6 u-line.com 5 Door Swing Dimensions Units have a zero clearance for the door to open 90°. Stainless Steel models require 2-1/8" door clearance to accommodate the handle if installed next to a wall. Other Site Requirements Side-By-Side Installation For a complete refreshment center, install two ...

u-line.com 7 Door Alignment and Adjustment Align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive frost may form in the interior. NOTICE • Properly aligned, the door’s gasket should be firmly in contact with th...

8 u-line.com Reversing Black or White Doors • The hinge hardware will be removed and reinstalled on the opposite side of the cabinet. • The top hinge hardware will be reinstalled on the bottom of the opposite side of the cabinet. • The bottom hinge hardware will be reinstalled on the top of the oppo...

u-line.com 9 Remove preexisting bottom hinge. 1. Remove the preexisting bottom hinge (three screws) (2). Reinstall hinge to top opposite. 1. Install the hinge just removed from the bottom to the TOP opposite side of the cabinet (three screws) (2). Reinstall Hole Plugs. 1. Install plastic screw plugs...

10 u-line.com 3. Grasp outer edge of stainless frame and firmly press inside edge of glass in while pulling stainless frame in opposite direction. 4. Unhinge frame from door. Assemble Stainless Frame 1. Prop frame against solid surface, handle side down and away 2. Insert door, logo forward, into fr...

u-line.com 11 Remove existing bottom hinge. 1. Remove the existing bottom hinge (three screws) (2). Reinstall hinge to top opposite. 1. Install the hinge just removed from the bottom to the TOP opposite side of the cabinet (three screws) (2). Reinstall Hole Plugs. 1. Install plastic screw plugs (thr...

12 u-line.com CAUTION ! To prevent permanent damage to the inner liner of the unit, the wire rack wood trim MUST be removed from the unit for staining and/or finishing. Allow stain/finish to dry thoroughly (at least 24 hours) in accordance with the stain/finish manufacturer’s instructions, prior to ...

u-line.com 13 Custom 1/4'' Thick Door Panel Insert Door Panel Preparation A custom door panel may be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness, where inserted into the door reveal (channel), is no more than 1/4" thick. For raise...

14 u-line.com Grille Overlay Your model’s grille is designed to accept a wood grille overlay. An overlay may be used to compliment a door overlay and provides a seamless look for your surrounding decor. Follow the instructions below to prepare and install your grille overlay. Be sure to read over th...

u-line.com 15 1/4 8-1/2 3-3/32 19-5/8 1/2 1/2 TYP 3X 5/16 TYP 2X (7/16 ) 5/16 10-5/16 11/64 2-1/8 1/2 22-7/8 23-7/8 FULL R Grille Ov erla y Dimensions 24 Inch Models Grille Drawing 24 inch

16 u-line.com 1/4 4-5/32 3-3/32 10-5/8 1/2 1/2 TYP 3X 5/16 TYP 2X (15/32 ) .275 5-29/32 11/64 2-1/8 1/2 13-7/8 14-7/8 FULL R Grille Ov erla y Dimensions 15 Inch Models Grille Drawing 15inch

u-line.com 17 Frame Preparation 2115WCOL 2175WCCOL & 2175BEVCOL Models Only An overlay frame covers the door frame to give a built-in appearance. Appropriate hardware and a copy of these instructions will be included with the unit. NOTICE The thickness of the overlay panel must be 3/4". 1. U...

18 u-line.com Prepare the New Overlay Panel NOTICE The overlay door panel must not weigh more than 20 lbs. The thickness of the door panel must be 3/4". 1. Place a towel, or similar, soft non-marking material out on a flat clean surface. Be sure the material is large enough to have the wood pane...

u-line.com 19 6. Use the door frame holes as a guide to drill pilot holes for the #6x1" pan head screws. 7. Attach the door to the overlay using #6x1" wood screws. NOTICE If you decide to drill pilot holes, remove the wood overlay from the door, and do not use a drill larger than 7/64". ...

20 u-line.com 11 Leveling Information It is recommended that the unit is level. 13. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown. 14. If the unit is not level, adjust the feet on the corners of t...

® INSTALLATION GUIDE ©2013 U-Line Corporation Publication Number 30282 4/2013 Rev.J The American Built-In Undercounter Leader Since 1962 U-LINE.COM BUILDING ON THREE GENERATIONS OF INNOVATION For over five decades and through three generations, U-Line continues to be the leader in innovation, qualit...