U-Line BI98 - Manuals

BI95, BI98, SP18 5 IMPORTANT IMPORTANT PLEASE READ all instructions completely before attempting to install, operate, or service your unit.• Proper installation procedures must be followed if this unit is being initially installed, or is moved to a new location after being in service. An INSTALLATIO...

6 BI95, BI98, SP18 Origins Ice MakerModels BI95, BI98, SP18 All Origins Ice Makers provide high daily ice production and storage capabilities, and conserve on water, using only 2-3/4 gallons (10.4 L) to produce approximately 22 lbs (10 kg) of ice. • Model 95 produces up to 23 lbs (10.4 kg) of ice pe...

BI95, BI98, SP18 7 Model SP18 To turn the unit on or off, press the rocker switch (Figure 3) located in the center of the lower grille. Ice Harvest Control Adjustments are not normally needed. The control is preset at the factory. IMPORTANT IMPORTANT Making adjustments may affect the daily ice produ...

8 BI95, BI98, SP18 Normal Operating Sounds All models incorporate rigid foam insulated cabinets to provide high thermal efficiency and maximum sound reduction for its internal working components. In spite of this technology, your model may make sounds that are unfamiliar. Normal operating sounds may...

BI95, BI98, SP18 9 Product Disposal If the unit is being removed from service for disposal, check and obey all Federal, State and/or Local regulations regarding the disposal and recycling of refrigeration appliances, and follow these steps completely: 1. Disconnect power to the unit and unplug the p...

10 BI95, BI98, SP18 Maintenance Proper maintenance of your U-Line product will ensure efficiency, top performance and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets or other special considerations. Defrosting Manual ...

BI95, BI98, SP18 11 6. Insert the grille screw (Figure 8, 1) and tighten. Do not over-tighten. 7. Reconnect power to the unit. Ice Maker Maintenance Inlet Screen Interval - Every Twelve Months The solenoid valve inlet screen must be cleaned at least once each year as follows: WARNING Disconnect elec...

12 BI95, BI98, SP18 Ice Cube Thickness Adjustment Interval - As Required The ice cube size may be adjusted by changing the amount of water injected into the ice maker assembly as follows: Figure 12 1. Remove the ice maker assembly cover (Figure 12) . Figure 13 2. Locate the adjusting screw on the ic...

BI95, BI98, SP18 13 Door Alignment Check and Adjustment IMPORTANT IMPORTANT Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps). Carefully examine the door’s gasket to assure that it is firmly in contact with the cabinet. Also make s...

BI95, BI98, SP18 15 Before Calling for Service If your U-Line product appears to be malfunctioning, read through the OPERATION section of this guide to ensure that the function of all controls are clearly understood. If the malfunction persists, the TROUBLESHOOTING GUIDE in this guide will assist yo...

16 BI95, BI98, SP18 Troubleshooting Guide DANGER ELECTROCUTION HAZARDNever attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected. Troubleshooting - What to check when problems occur: PROBLEM POSSIBLE CAUSE REMEDY The unit frosts up. Unit is manual...

BI95, BI98, SP18 19 U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator...

For General Inquiries: P.O. Box 245040Milwaukee, Wisconsin 53224-9540 U.S.A.Phone (800) 779-2547 FAX (414) 354-5696www.U-Line.com For Service and Parts Assistance: Phone (800) 779-2547 (414) 354-0300 FAX (414) 354-5696Email: [email protected]: [email protected]...