Tyco MM23016 - Manuals

MM23016, Rev. C 9 1 SAFETY SYMBOL CONVENTION The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific ...

MM23016, Rev. C 10 2 RF ENERGY EXPOSURE INFORMATION 2.1 RF ENERGY EXPOSURE AWARENESS, CONTROL INFORMATION, AND OPERATION INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS Before using your mobile two-way radio, read this important RF energy awareness and control information and operational instruct...

MM23016, Rev. C 11 2.2 COMPLIANCE WITH RF EXPOSURE STANDARDS Your MA/COM, Inc. M7200 mobile two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy. This radio complies wi...

MM23016, Rev. C 12 Install the radio’s antenna (refer to Table 2-1 for applicable antenna part numbers) in the center of the vehicle’s roof. These mobile antenna installation guidelines are limited to metal body motor vehicles or vehicles with appropriate ground planes. The antenna installation shou...

MM23016, Rev. C 14 3 OPERATION SAFETY RECOMMENDATIONS 3.1 TRANSMITTER HAZARDS The operator of any mobile radio should be aware of certain hazards common to the operation of vehicular radio transmitters. A list of several possible hazards is given: • Explosive Atmospheres – Just as it is dangerous to...

MM23016, Rev. C 15 4 OPERATING RULES AND REGULATIONS Two-way FM radio systems must be operated in accordance with the rules and regulations of the local, regional, or national government. In the United States, the M7200 mobile radio must be operated in accordance with the rules and regulations of th...

MM23016, Rev. C 16 5 PRODUCT DESCRIPTION The M7200 mobile is a state-of-the-art radio that operates seamlessly between the 800 MHz frequency band and the 700 MHz frequency band. The M7200 is designed to meet the critical communications demands of public service users and complies with MIL-STD-810F s...

MM23016, Rev. C 17 6 CHANGE OPERATING MODE 6.1 CHANGE FROM OTP MODE To change from OTP operating mode to P25, EDACS, or Conventional: 1. Use to cycle through the menu until the “Mode Menu” appears in the bottom line of the display. 2. Use to choose an available mode. Press MENU and confirm (Y/N) wit...

MM23016, Rev. C 18 7 OPENSKY OPERATION 7.1 CH721 FRONT PANEL COMPONENTS The front panel of the control head includes a dot matrix display, controls for menu navigation, an emergency button, three pre-set buttons, a Power On-Off/Volume Control knob, and a microphone connector. In addition, the system...

MM23016, Rev. C 19 The buttons on the front panel are backlit for operation in a low ambient light level such as nighttime operation. Some buttons also flash to provide feedback of various operating conditions. In addition, the front panel contains a light-level sensor that samples ambient light lev...

MM23016, Rev. C 20 2. Wait for the power-up sequence to complete, which takes approximately ten (10) seconds. During this time, if enabled for auto registration, the radio is provisioned with a customized user personality designed for the user’s specific needs by the OpenSky network administrator. I...

MM23016, Rev. C 21 7.5 LOG OFF THE NETWORK The *0## command de-registers the radio. Typically, this is automatically performed when powering down the radio. Using this method, the User ID is remembered by the radio so only the password is needed at next login. Manually log off by pressing *0## (requ...

MM23016, Rev. C 22 7.8 RADIO STATUS ICONS Status Icons indicate the various operating characteristics of the radio. The icons show operating modes and conditions (see Table 7-2). The location of icons on the display may vary depending on configuration. Table 7-2: Icons and Descriptions ICON DESCRIPT...

MM23016, Rev. C 23 TG a TG b TG c TG x TG y TG z TG d TG e TG f TG a TG d TG g TG h TG i TG = Talk Group Profile 1 Profile 2 Profile 3 Figure 7-4: Personality Structure Example If Global Profile is enabled by the system administrator, the number of available talk groups to scan doubles. 7.10.2 Talk ...

MM23016, Rev. C 24 7.11 ALERT TONES The M7200 radio also provides audible Alert Tones or “beeps” to indicate the various operating conditions (see Table 7-3). Table 7-3: M7200 OpenSky Mode Alert Tones NAME TONE DESCRIPTION Call Queued one low tone/two high tones Call queued for processing. Call Deni...

MM23016, Rev. C 28 7.14.2 DTMF Overdial Using the keypad on a System Model, the radio can transmit DTMF tones corresponding to numbers/characters 0 — 9, * and # on the keypad. To overdial numbers/characters, transmit by pressing and holding the PTT button and then, press the corresponding keys (one ...

MM23016, Rev. C 29 When stealth mode is on, the radio continues to scan the programmed list of talk groups and the user can key-up on the selected talk group. 7.18.1 Enabling Stealth Mode 1. Using , scroll through the menu until “StealthMenu” appears. 2. To immediately turn Stealth Mode on, press ( ...

MM23016, Rev. C 31 7.23 INTERCOM MODE The optional intercom mode gives users at multiple control heads connected to the same radio the ability to communicate with each other without transmitting over-the-air. Turn intercom mode on and off using the “INTERCOM” menu as follows: 1. Use to cycle through...

MM23016, Rev. C 33 Table 7-6: Scan Modes SCAN MODE EXPLANATION No Scan Eliminates distractions . Full communications (transmit and receive) on selected talk group. No calls received from other talk groups. Normal (Default) The user can scan all talk groups in the active profile that are not locked o...

MM23016, Rev. C 34 7.25.2 Scanning Priority The following lists the scanning priority order (from highest to lowest): 1. Selected talk group in emergency state 2. Default emergency group in emergency state 3. Selected talk group 4. Emergency capable group in emergency state 5. Priority 1 talk group ...

MM23016, Rev. C 36 7.27 SELECTIVE ALERT Selective alert messaging is an OTP feature allowing one of up to eight (8) pre-programmed text messages (refer to Section 7.27.3) to be sent from one radio to another. The user specifies a destination radio’s User ID, selects one of the pre-programmed text me...

MM23016, Rev. C 37 Table 7-7: Status of Selective Alert STATUS MESSAGE DEFINITION Delivering Select Alert message transmit attempt Busy Too busy – Try again Dest Down Receiving radio not logged on – Not registered Not Reg Transmitting radio not logged on – Not registered Delivered Transmission compl...

MM23016, Rev. C 38 1. Press the * 9 keys. 2. Enter the telephone number. Ignore dashes/spaces, and precede the number with any required access digits such as a 1 for long distance. 3. Press the # key. 4. Wait a few seconds and then press and release the mic’s PTT button to initiate the call. An init...

MM23016, Rev. C 39 • If the emergency behavior of the active profile is Default, the radio moves to the default emergency voice group of the profile and this talk group becomes the select talk group. The display will alternate between the emergency voice group name and “EMERGENCY” and declaring User...

MM23016, Rev. C 41 generation are generated automatically by the system and provisioned to authorized users. This process requires that authorized users login to the network and be authenticated. Encryption keys require no manual handling and are never sent “in the clear” over any network interface ...

MM23016, Rev. C 43 8 P25/EDACS/CONVENTIONAL COMMON OPERATION 8.1 CH721 FRONT PANEL COMPONENTS The front panel of the control head includes a dot matrix display, controls for menu navigation, an emergency button, three pre-set buttons, a Power On-Off/Volume Control knob, and a microphone connector. I...

MM23016, Rev. C 44 Table 8-1: Front Panel Default Controls and Functions PART FUNCTION Power On-Off/Volume Control knob Turn knob clockwise to power on the radio and increase volume. Turn counter-clockwise to decrease volume and power off the radio. Mic Connection Connection for hand-held, hands-fre...

MM23016, Rev. C 45 PART FUNCTION DIS Used to adjust the current display intensity and the keypad backlight level. IND Used to call an individual or make an all-call by selecting the individual call function. 8.1.1 Primary Functions (Quick Access) The secondary function of the SCAN button is to toggl...

MM23016, Rev. C 46 Line 1 shows the currently selected item name (XXXXXXXX) from the list. Line 2 indicates the list (YYY) that the selection is to be made from and the number of the selected item (ZZZ) within the list. (In some cases the information on lines 1 and 2 will be exchanged.) Enter the sy...

MM23016, Rev. C 49 FEATURE NUMBER POSSIBLE FEATURES STANDARD OR OPTIONAL 33 P25 Common Air Interface Optional 34 Direct Frequency Entry Optional 38 Radio TextLink Optional 8.6 SYSTEM/GROUP/CHANNEL SELECTION In the following description of SYSTEM/GROUP/CHANNEL SELECTION , the term group is used for b...

MM23016, Rev. C 51 8.8.3 ProVoice Digital Mode ProVoice digital mode allows the radio to transmit and receive digitized voice signals. These digital signals provide improved weak signal performance and they cannot be easily monitored with a standard receiver. Groups and channels programmed for ProVo...

MM23016, Rev. C 52 • If Private mode is disabled and a private call is received, the Reply transmission will be in Private mode if the transmission is made during the scan hangtime. If the reply transmission occurs after the scan hangtime, the transmission will be in Clear mode. When operating on a ...

MM23016, Rev. C 54 8.9 MACRO KEY OPERATION Macro key operation permits the user to accomplish a series of keystrokes with a single "macro" keystroke. Up to ten (10) macro keys can be defined, each capable of executing up to twenty (20) keystrokes, to any pushbutton input (i.e., keypad keys, ...

MM23016, Rev. C 55 9 EDACS AND P25 TRUNKED OPERATION 9.1 RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. Figure 9-1: Typical Display Table 9-1: Icons and Descriptions ICON DESCRIPTION Indicates the EDACS system is in Failsoft™ mode (if ena...

MM23016, Rev. C 59 NAME TONE DESCRIPTION Carrier Control Timer Five short high-pitched warning tones followed by a long low-pitched tone. Sounds if the programmed time for continuous transmission is exceeded. The transmitter will shut down shortly after the alert, interrupting communications. Releas...

MM23016, Rev. C 62 9.5 RECEIVING A CALL 1. Turn the radio on by rotating the POWER ON-OFF/VOLUME knob clockwise (out of detent). A short alert signal (if enabled through programming) indicates the radio is ready to use. 2. The display shows the last selected or the power up (depending on programming...

MM23016, Rev. C 63 9.8 EMERGENCY OPERATION The radio's ability to declare an emergency, clear an emergency, remain locked on an emergency and group, and the emergency audio and display freeze can each be enabled or disabled through programming. When an emergency is declared scanning will stop and wi...

MM23016, Rev. C 64 accomplished by enabling each radio to analyze the signal quality of its current control channel and compare it with the signal quality of the control channel for each site in its adjacency scan list. (The signal quality metric used for the ProScan algorithm is based on a combinat...

MM23016, Rev. C 65 programmed to provide Trunked Priority Group Scan capability, which operates similar to priority scan in Conventional mode. The following is a description of programmable scan features that should be helpful in understanding the Group Scan Operation of the radio: Scan Hang Time - ...

MM23016, Rev. C 66 9.10.3 Nuisance Delete A group can also be deleted from the scan list, if it is not the currently selected group by pressing ( - ) with during scan operation while the radio is displaying the unwanted group. The group will be deleted from the system's group scan list in the same m...

MM23016, Rev. C 67 programmed to ring when an individual call is received. If enabled, the ring begins five seconds after the caller unkeys and will continue until the PTT button, the CLR button, or IND is pressed. Hookswitch functions the same as CLR key in I-CALL, phone call, and menu modes. If a ...

MM23016, Rev. C 69 9.13.2 Sending a Telephone Interconnect Call (Trunked Mode Only) Use the following procedures to initiate and complete a Telephone Interconnect call: 1. To select a previously stored phone number, select phone call mode from the menu, press PHN and use the ramp control to scroll t...

MM23016, Rev. C 74 Pressing and holding the CLEAR (Scan Model) or CLR (System Model) button for 2.5 seconds toggles the user into and out of the dynamic regroup group set. A double beep will sound for entry or exit. The display will indicate REGR_0x where "x" is a digit of 1 to 8 indicating ...

MM23016, Rev. C 75 10 CONVENTIONAL OPERATION 10.1 RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. The icons appear on the first line of the display. Figure 10-1: Typical Display Table 10-1: Icons and Descriptions ICON DESCRIPTION Indicates...

MM23016, Rev. C 79 FEATURE DISPLAY PARAMETER SETTINGS COMMENT Scan Add Menu item: SCAN ADD Once selected: Proper scan icon displayed. S, 2 or 1 Adds group or channel to scan list. Scan Delete Menu item: SCAN DEL Once selected: Scan icon goes out. Deletes group or channel from scan list. Scan Add/Del...

MM23016, Rev. C 80 4. The radio is now ready to receive calls. 5. When the radio receives a call (and the correct encoding is decoded, if programmed and enabled), it unmutes on the channel and the BSY indicator comes on. 10.6 SENDING A CALL 1. Turn ON the radio and set the POWER ON-OFF/VOLUME knob t...

MM23016, Rev. C 81 10.7.2 Tone Encode Transmission In conventional mode, two keys can be defined to be tone encode triggers. If either one of the pre-programmed tone encode triggers is pressed, a pre-programmed tone sequence will be transmitted on the current system and channel. (See Section 10.7 if...

MM23016, Rev. C 82 5. A third press of ( + ) sets the channel for Priority 1 (P1) scanning and is displayed on line 1. If the P1 or P2 channels are already set and a new channel is then assigned as the P1 or P2 channel, the previously assigned priority channel will change to non-priority scanning. T...

MM23016, Rev. C 84 enable or disable Type 99 decode. The pre-programmed key light will blink when Type 99 is disabled by the hookswitch. Type 99 decode will continue to be active while the radio's CLR button is pressed. This allows the user to monitor calls and still be alerted when a call is direct...

MM23016, Rev. C 85 11 P25 CONVENTIONAL OPERATION 11.1 RADIO STATUS ICONS Status icons are indicators that show the various operating characteristics of the radio. The icons appear on the first line of the display. Figure 11-1: Typical Display Table 11-1: Icons and Descriptions ICON DESCRIPTION Indic...

MM23016, Rev. C 90 FEATURE DISPLAY PARAMETER SETTINGS COMMENT Mute Menu item: MUTE ON, OFF Toggles the mute function ON or OFF to control the audio output from the selected radio. Mute #1 Menu item: MUTE 1 ON, OFF Toggles the mute 1 function ON or OFF on radio #1. Mute #2 Menu item: MUTE 2 ON, OFF T...

MM23016, Rev. C 91 11.6 INDIVIDUAL CALLS IN P25 MODE 11.6.1 Transmitting an Individual Call 1. Select the desired P25 system. 2. Select the radio unit to call (callee source ID) from the pre-programmed individual call list or enter the ID number on the radio keypad. 3. Press and hold the PTT. 4. Whe...

MM23016, Rev. C 92 11.7.2 Receiving an Emergency Group Call 1. Select the desired P25 System and Talk Group/Channel. 2. When the radio detects an incoming Emergency Group Call, the radio will sound an alert tone and “ RXEMER ” will appear in the display. 3. Voice or emergency transmissions will be h...

MM23016, Rev. C 93 12 BASIC TROUBLESHOOTING If the radio is not operating properly, check Table 12-1 for likely causes. For additional assistance, contact a qualified service technician. Table 12-1: Basic Troubleshooting SYMPTOM CAUSE SOLUTION Radio will not turn on. No power. Test the connection to...

MM23016, Rev. C 94 SYMPTOM CAUSE SOLUTION Screen displays: NOAUTHM VNIC authentication of the radio failed. Contact system administrator. Screen displays: NOSUPRT The voice authentication security policy is set to only allow authenticated users. Contact system administrator. Encrypted calls cannot b...

MM23016, Rev. C 95 13 TECHNICAL ASSISTANCE The Technical Assistance Center's (TAC) resources are available to help with overall system operation, maintenance, upgrades and product support. TAC is the point of contact when answers are needed to technical questions. Product specialists, with detailed ...

MM23016, Rev. C 96 14 KEYPAD REMAPPING If the keys have been remapped to provide new functions, fill in the following template for future reference. Button Function Button Function Emergency 1 Preset A 2 Preset B 3 Preset C 4 Rocker • 5 Rocker •• 6 Rocker + 7 Rocker - 8 MENU 9 OPT/OPTION * CLR/CLEAR...

MM23016, Rev. C 97 15 RADIO SETUP RADIO TYPE: FREQUENCY BAND: OPERATOR'S NAME: EMERGENCY GROUP: SYSTEM NUMBER SYSTEM NAME TRK/CNV GRP/CHN NUMBER GRP/CHN NAME USE