Troy-Bilt 47330- Manuals

Section 1: Safety Maintenance and Storage 1. Before performing any maintenance or adjustments, shut the engine off, wait for all moving parts to come to a complete stop, and disconnect and secure the spark plug wire away from the spark plug. Allow unit to cool before working near it or plac­ing a st...

Section 3I Features and Controls A WARNING Before operating your machine, carefully read and under- sfand all safety, controls, and operating Instructions In this Manual, In the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these Instructions can result in serio...

10 Section 3: Features and Controls Figure 3-S: Squeeze clutch lever against handlebar when starting engine. Release clutch lever slowly after engine starts. Figure 3-6: Squeezing the clutch lever against the handlebar causes the Idler pulley to move away from fhe belt, taking tension off the heft w...

Section 4I Operation A WARNING Before operating the unit, carefuiiy read and understand all safety, controls and operating instructions in this Manual, in the separate Engine Owner’s Manual, and the decals on the machine. Failure to follow these instructions can result in serious personal injury. A ...

Section 4: Operation 4. Push the rocker ON/OFF switch (Figure 3-8) to the ON position. 5. Squeeze the clutch lever (Figure 3-5) up against the handle. Grasp the engine starter rope handle and pull slowly until resistance is felt. Then pull cord rapidly to overcome compression, prevent kickback and s...

14 Section 4: Operation USING THE SHREDDER IMPORTANT: Always wear safety goggles (with side shields), appropriate gloves, and hearing protection. Read and follow the safety rules in this Manual. A DANGER Contact with rotating cutting blades will cause serious personal injury. The blades rotate when ...

Section 4: Operation 15 J Wet, soggy, or “green” materials will be shredded to a medium consistency when using the Bar Grate. However, to shred these materials to an even finer consis­ tency, you may wish to process the mate­ rial a second time. If you do not have the optional Bar Grate attachment, ...

Section 4: Operation Figure 4-7: The illseharge screen must be positioned as shown above. The holes In the tubes at tbe screen ends must align with the holes In the machine wall. Reinstall discharge screen rods and then hairpin cotters. A DANGER Do not shred brush, branches or other material when ba...

Section 51 Maintenance A WARNING Moving parts on the unit can cause seri­ ous personai injury. Shut off the engine, iet aii moving parts stop completeiy, disconnect the spark piug wire and prevent it from touching the spark piug before performing any maintenance or service procedures. il Maintenaiic...

18 Section 5: Maintenance A WARNING Faiture to foitow these instructions can resutt in serious personat injury or property damage. Before inspecting, cieaning or servicing the machine, shut off engine, wait for ait moving parts to come to a comptete stop, disconnect spark ptug wire and move wire awa...

Section 5: Maintenance 19 Before Inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property...

20 Section 5: Maintenance 'A A WARNING Faiiure to foiiow these instructions can result in serious personal injury or property damage. Before inspecting, cieaning or servicing the machine, shut off engine, wait for aii moving parts tocome to a compiate stop, disconnect spark piug wire and move wire a...

Section 5: Maintenance 21 J Before inspecting, cieaning or servicing the machine, shut off engine, wait for aii moving parts to come to a compiete stop, disconnect spark piug wire and move wire away from spark piug. Faiiure to foiiow these instructions can resuit in serious personai injury or proper...

22 Section 5: Maintenance A WARNING W Failure to follow these instructions can result in serious personal injury or property damage. Before inspecting, cieaning or servicing the machine, shut off engine, wait for ail moving parts to come to a compiete stop, disconnect spark plug wire and move wire a...

Section 5: Maintenance Before inspecting, cieaning or servicing the machine, shut off engine, wait for aii moving parts to come to a compiete stop, disconnect spark piug wire and move wire away from spark piug. Failure to follow these instructions can result in serious personal injury or property da...

24 Parts List Drawing No. 1 Models 47329 and 47330 40 ,V./ "iSj f / 3 0 i d " \ N 1 s . \ _____________________L I \ 28*-iT' .-.^82 30 1200 71 >* N 70 24 .23 ■£:::387 « J i iP «r 74 ) 12 / a”*“ ■A»-.!« 11 ■«, * \ ^ “ > 52 2S 58j 57 C» 57

ifiartslist JHodels 47329 and 47330 Ref. Part No. Description Qty. Ref. Part Ne. Descriptien Qty. 2 1773249010 Closure Assembly, Left Hand....... .... 1 54 1766972 Extension Spring................................ 1 3 1186327 Flange Screw, 5/16-18 x 1/2......... .... 10 55 1762636 V-Belt................

2S Parts List Models 47329 and 47330 Drawing No. 2 15 Ref. Part No. Description Qty. Ref. Part No. Description Qty. 1 1762607 Cylinder Weldment...................... ..... 1 10 1763110 Short Outer Sleeve, 1/2.................... .... 1 2 1762611 Cylinder Pin................................. ..... 3 ...

CUSTOMER SERVICE INFORMATION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory so that we can provide you with warranty benefits and informational bulletins. Warranty Service The warranty statement ...