Troy-Bilt 410, 420 - Manuals

Page 2 - Finding and Recording Model Number; Please do; Table of Contents; . Click on Customer Service at the bottom of the page.

2 Finding and Recording Model Number Please do NOT return the unit to the retailer from which it was purchased, without first contacting Customer Support. Table of Contents BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT, please locate the model plate on the equipment and copy the information to the ...

Page 3 - WARNING

3 1 Safety Labels WARNING This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at-tempting to operate this machine. Failure to comply with these i...

Page 4 - Training

4 2 Safe Operation Practices Training 1. Read, understand, and follow all instructions on the ma- chine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. 2. Be familiar with all contro...

Page 5 - Safe; Your Responsibility

Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of a...

Page 6 - Loose Parts In Carton

6 3 Setting Up Your Chipper Shredder NOTE: This Operators Manual covers a range of product specifications for various models. Characteristics and features discussed and /or illustrated in this manual may not be applicable to all models. Troybilt LLC reserves the right to change product specification...

Page 7 - Setting Up; Never place branches

7 Figure 4 3 Setting Up Your Chipper Shredder Know Your Chipper Shredder WARNING Never operate the chipper shredder with the chipper chute in the raised position. Use the spring latch to lower the chipper chute into the operat- ing position before starting the engine. IMPORTANT Never place branches ...

Page 8 - Starting Engine; Stopping Engine

8 4 Operating Your Chipper Shredder This Operators Manual covers a range of product specifications for various models. Characteristics and features discussed and /or illustrated in this manual may not be applicable to all models. Troy Bilt LLC reserves the right to change product specifications, des...

Page 9 - Operating; Clearing the Hopper; Chipping

9 4 WARNING Never operate the chip- per shredder without chipper chute lowered into the operating position. Figure 7 Operating Your Chipper Shredder Operating The Chipper ShredderShredding Yard waste such as leaves and pine needles can be placed in the hopper for shredding. After material has been p...

Page 11 - IMPORTANT; Storing Your Chipper Shredder

11 WARNING Figure 10 Figure 11 The shredder blade is sharp. Wear leather work gloves to protect your hands. Maintaining Your Chipper Shredder IMPORTANT Make certain chipper blades are reassem-bled with the sharp edge outward (toward the chipper chute). Torque hardware to between 20 ft.-lbs and 25 ft...

Page 12 - Trouble; Cause

12 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position (if equipped). 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped)....

Page 13 - Parts List; To order replacement

13 7 Parts List To order replacement parts, contact 1-800-520-5520, 1-330-558-7220 or visit www.troybilt.com. 1 681-04009 Impeller Assembly Complete 2 710-1054 Machine Screw, 5/16-24 x 1.0 3 711-0833B Clevis Pin,.496 4 712-0411 Hex Lock Nut, 5/16-24 5 715-0166 Spiral Pin,.156 x 1.0 6 719-0329 Flail ...

Page 16 - MANUFACTURER’S LIMITED WARRANTY FOR

The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and /or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and /or its territories and possess...