Trane X1351152801 - Manuals

6 BAS-SVX10C-EN General Information Part Numbers The following table lists part numbers for each sensor type. The following table lists part numbers for optional accessories. Sensor type Features Part number BAYSENS Global parts Setpoint Fan control System Occupancy LEDs Temperature sensors Single N...

BAS-SVX10C-EN 7 General Information Dimensions The following illustration provides specific dimension details. The dimensions are the same for all models. 2.9 in (73.5 cm) 1.08 in (27.5 mm) 4.68 in (118.9 mm) 1.45 in (36.8 mm) 0.63 in (15.9 mm) 0.31 in (8 mm) 0.12 in (3 mm) TYP R.07 in (R1.9) mm) 3....

BAS-SVX10C-EN 9 Installation and Configuration: Display Sensor This section provides step-by-step installation instructions for the display sensor (see applicable part numbers for the temperature sensor with LCD display on p. p. 6 ). For installation of all other sensor models, see p. 17 . Read thro...

10 BAS-SVX10C-EN Installation and Configuration: Display Sensor Wiring the Sensor  WARNING Hazardous voltage! Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power cannot be inadvertently energized. Failure to disco...

BAS-SVX10C-EN 11 Installation and Configuration: Display Sensor Configuring the Display Sensor The configuration of the display sensor determines which system features can be accessed and changes can be made by the tenant (for example, changes to cooling/heating mode, setpoint, or fan speed. Verify ...

BAS-SVX10C-EN 15 Installation and Configuration: Display Sensor Optional Configuration Features Displaying Setpoint or Temperature You can configure the sensor to display either the temperature (default) or setpoint. To select either option: 1. Verify that the sensor is in operating mode and at the ...

16 BAS-SVX10C-EN Installation and Configuration: Display Sensor 3. Press the left and right arrows for 4 seconds. The lock symbol will appear on the display to indicate that the setting has been locked. Note: If you try to access a feature that is locked, the locked symbol appears on the display. If...

BAS-SVX10C-EN 17 Installation: All Models Other Than the Display Sensor This section provides step-by-step installation instructions for all sensor models other than the display sensor. (For installation of the display sensor, see p. 9 .) Read through the pre-installation information before proceedi...

BAS-SVX10C-EN 21 Installation: All Models Other Than the Display Sensor Changing the Setpoint Thumb Wheel (optional) Sensors with temperature setpoint control have pre-installed Fahrenheit setpoint thumb wheels. A Celsius setpoint thumb wheel is included with these sensors. An optional hot/cold setp...

BAS-SVX10C-EN 23 Operation This section describes sensor operations. Changing Temperature Settings To change temperature settings: • For sensors with temperature setpoint thumb wheels (located on top of the sensor), rotate the thumb wheel to the desired temperature setting. Note: If you need to chan...

24 BAS-SVX10C-EN Operation Selecting Temporary Occupancy (Timed Override) Temporary occupancy (timed override) is available on some sensors. Temporary occupancy can be selected to adjust temperature, fan, or heat/cool settings after the system has changed to unoccupied mode. System control will reve...

BAS-SVX10C-EN 25 Operation Service Pin Request Some sensor models can communicate a service pin request to their connected unit controller. Sensors with Occupied/Unoccupied Buttons To initiate a service pin request, press the Occupied button ( Figure 2, p. 24 ) for 10–25 seconds. The following occur...

26 BAS-SVX10C-EN Operation Star(*)/Double Star(**) Function The star/double star function is available on sensor models with thumb wheels and on the display sensor. Note: Consult the appropriate unit controller documentation for information about this function. Sensors with Thumb Wheels Turning the ...

BAS-SVX10C-EN 27 Operation Display Sensor Operation This section describes display sensor operation. Figure 5 shows an example of a display sensor that has been configured and is in operating mode. Changing Temperature Settings Changing Heating and Cooling Temperature Settings (dual setpoint systems...

BAS-SVX10C-EN 29 Maintenance and Troubleshooting This section describes sensor features that can be used for maintenance and troubleshooting. LEDs Some sensor models have LEDs. They are located on the front cover and convey the following information: Error Codes (Display Sensor) For an explanation o...

30 BAS-SVX10C-EN Maintenance and Troubleshooting Measuring Output Resistance Measure output resistance as follows, according to sensor type. Display Sensors For display sensors, measure the outputs for zone temperature, setpoints, heat setpoint, and system/fan mode as described: 1. Ensure that the G...

BAS-SVX10C-EN 31 Maintenance and Troubleshooting Table 1. Resistance measurements for zone temperature and setpoints Zone or setpoint temperature Nominal zone temperature output resistance Nominal setpoint and heating setpoint output resistance ** NA 938 Ω 55°F (12.8°C) 17.47 k Ω 792 Ω 60°F (15.6°C)...

32 BAS-SVX10C-EN Maintenance and Troubleshooting Cleaning the Sensor NOTICE Equipment damage! Spraying glass cleaner or any other solution directly on the sensor may damage it. You can clean the sensor by applying glass cleaner to a soft, non-abrasive cloth, and gently wiping the face, including the...

BAS-SVX10C-EN 33 Wiring Diagrams Each wiring diagram is identified by sensor part number (see “Part Numbers,” p. 6 for reference.) For wiring information for the display sensor, see Figure 1, p. 10 . TimedoverrideUnoccupied(Cancel) SW2 R1, 1.5 k Ω TimedoverrideOccupied(On) SW1 RT1thermistor,10 k at ...

34 BAS-SVX10C-EN Wiring Diagrams TimedoverrideCancel SW2 R1, 1.5 k Ω Timed overrideOn SW1 Zonetemperature Signal common 1 2 RT1 thermistor,10 k at 25°C Ω Dwg source: 3270 3438 Ti m ed overrideCancel S W 4 R9, 1.5 k W Ti m ed overrideOn S W 3 Ther m istor, 10 k at 25°C W 1 2 4 CalibrationPot 1 (see )...

40 BAS-SVX10C-EN Wiring Diagrams 2 (+) 1 (–) COMM Module J1 23 Optional COMM module X1365146702

BAS-SVX10C-EN 41 Specifications and Agency Compliance Agency Compliance • United States: – UL listed: 94, 5 VA Flammability rating; 916, Energy management equipment – FCC Part 15, Subpart B • Canada: – CUL listed: 916, Energy management equipment • Europe: – CE marked Specifications Sensor operating...

42 BAS-SVX10C-EN Specifications and Agency Compliance CE Declaration of Conformity Manufacturer: Trane, 4833 White Bear Parkway, Saint Paul, MN 55103, USA Product: Wired display sensor Model number: X1379088601, X1379088604, X1379088605 The manufacturer hereby declares that the product conforms to t...