TP-Link TL-SL3452 - Manuals

IV Contents Contents Chapter 1 Introduction ———————————— 01 1.1 Product Overview .........................................01 1.2 Appearance .................................................01 Chapter 2 Installation ————————————— 04 2.1 Package Contents .........................................04 2.2...

01 L2 Managed Switch Introduction ChaCter C Product Overview C1C TP-LINK JetStream TM L2 Managed Switch, designed for workgroups and departments, provides wire-speed performance and abundant layer 2 management features. It provides a variety of service features and multiple powerful functions with h...

02 L2 Managed Switch LEDs LED Status Indication PWR On The Switch is powered on Off The Switch is powered off or power supply is abnormal Flashing Power supply is abnormal SYS Flashing The Switch works properly On/Off The Switch works improperly 10/100Mbps On A device is linked to the corresponding ...

03 L2 Managed Switch Note: For TL-SL3428, when using the SFP port with a 100Mbps module or a gigabit module, ■ you need log on to the GUI (Graphical User Interface1 of the Switch and configure its corresponding Speed and Duplex mode on Switching → Port → Port Config page. For 100Mbps module, please ...

04 L2 Managed Switch Installation ChaCter 1 Package Contents 11C Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Resource CD One Switch One Power Cord, one Console Cable and one Ground Cable This Installa...

05 L2 Managed Switch Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantl...

06 L2 Managed Switch protection measures should be taken. Ensure the rack and device are well earthed. ■ Make sure the power socket has a good contact with the ground. ■ Keep a reasonable cabling system and avoid induced lightning. ■ Use the signal SPD (Surge Protective Device1 when wiring outdoor. ...

07 L2 Managed Switch Turnover the device and attach the supplied rubber feet to the recessed areas on 3. the bottom at each corner of the device. L2 Managed Switch TL -S L3 42 8 Feet Bottom of the Device Notch Desktop Installation Figure 2-1 Rack Installation ■ To install the device in an EIA standa...

08 L2 Managed Switch Lightning Protection ChaCter 2 Cabling Reasonably 21C In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devi...

10 L2 Managed Switch Connect to Ground 211 Connecting the device to ground is to quickly release the lightning over-voltage and over-current of the device, which is also a necessary measure to protect the body from electric shock. In different environments, the device may be grounded differently. Th...

11 L2 Managed Switch Note: The figure is to illustrate the application and principle. The power cord you get from ■ the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above.If you intend to connect the device to the ground...

12 L2 Managed Switch Use Lightning Arrester 212 Power lightning arrester and signal lightning arrester are used for lighting protection. Power lightning arrester is used for limiting the voltage surge due to a lightning. If an outdoor AC power cord should be directly connected to the device, please ...

13 L2 Managed Switch Connection Connection ChaCter 2 Ethernet Port 21C Connect the Ethernet ports of the Switch to the network devices by RJ45 cable as the following figure shown. L2 Managed Switch TL-SL3428 RJ45 Cable RJ45 Port Connecting the RJ45 Port Figure 4-1 SFP Port 211 Connect the SFP port t...

14 L2 Managed Switch Connection Console Port 212 CLI (Command Line Interface1 enables you to manage the Switch, thus you can load the CLI after connecting the PCs or Terminals to the console port on the Switch via the provided cable. Connect the console port of the device with your computer by the c...

15 L2 Managed Switch Connecting to Power Supply Figure 4-4 Note: The figure is to illustrate the application and principle. The power cord you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. Initializati...

16 L2 Managed Switch Configuration ChaCter 4 Configure the Switch via GUI 41C To access the GUI of the Switch, open a web browser and t ype the default 1. management address http://192.168.0.1 in the address field of the browser, then press the Enter key. Web Browser Figure 5-1 Note: To log on to th...

17 L2 Managed Switch Main Page of the Switch Figure 5-3 Configure the Switch Using CLI 411 You can log on to the Switch and access the CLI by the following two methods: Log on to the Switch by the console port on the Switch. ■ Log on to the Switch remotely by a Telnet or SSH connection through an Et...

18 L2 Managed Switch The Connection Description Window will prompt as Figure 5-5. Enter a name into the 3. Name field and click OK. Connection Description Figure 5-5 Select the port to connect in Figure 5-6, and click OK. 4. Select the port to connect Figure 5-6 Configure the port selected in the st...

19 L2 Managed Switch Port Settings Figure 5-7 Type the User name and Password in the Hyper Terminal window, the factory default 6. value for both of them is admin. The DOS prompt” TP-LINK>” will appear after pressing the Enter button as Figure 5-8 shown. It indicates that you can use the CLI now....

20 L2 Managed Switch Open the Run window Figure 5-9 Type cmd in the prompt Run window as Figure 5-10 and click OK. 3. Run Window Figure 5-10 Type telnet 192.168.0.1 in the command prompt shown as Figure 5-11, and press the 4. Enter button. Connecting to the Switch Figure 5-11 Configuration

21 L2 Managed Switch Type the User name and Password (the factory default value for both of them is 5. admin1 and press the Enter button, then you can use the CLI now, which is shown as Figure 5-12. Log in the Switch Figure 5-12 For detailed CLI configuration instructions, please refer to the CLI Re...

22 L2 Managed Switch Troubleshooting ACCendiA A What could I do if I forgot the username and Cassword of the Switch? QC1 Connect the console port of the PC to the console port of the Switch and open hyper 1. terminal. Power off and restart the Switch. When you are prompted that “Press CTRL-B to ente...

23 L2 Managed Switch Hardware SCecifications ACCendiA B Item Content Standards IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX/100Base-FX IEEE 802.3ab 1000Base-T IEEE 802.3z 1000Base-X IEEE 802.3x Flow Control Transmission Medium 10Base-T: UTP/STP of Cat. 3 or above (maximum 100m1 100Base-TX: 2-...

24 L2 Managed Switch Technical SuCCort ACCendiA C For more help, please go to: http://www.tp-link.com/en/support/faq ■ To download the latest Firmware, Driver, Utility and User Guide, go to: ■ http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the ...