TP-Link TL-SL1351 - Manuals

Page 2 - COPYRIGHT & TRADEMARKS; Specifications are subject to change without notice.; FCC STATEMENT; ) This device may not cause harmful interference.

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form ...

Page 4 - CONTENTS; Chapter 1

CONTENTS Package Contents: ............................................................................. 1 Chapter 1 Introduction of the Product ......................................... 1 1.1 Overview of the product .................................................................... 1 1.2 Features...

Page 5 - Overview of the product

1 Package Contents The following items should be found in your box: ¾ One Switch ¾ One power cord ¾ This User's Guide ¾ Rubber footpads for Desk-mount ¾ Rack-mount kit for installing the switch in a 19-inch rack Note: Make sure that the package contains the above items. If any of the listed items ar...

Page 6 - Features; Chapter 2 Installation; Mounting the Switch on a Desk

2 Uplink ports, and any port can be simply plugged into a server, a hub, a router or a switch, using the straight cable or crossover cable. Diagnostic LEDs which display link status and activity, allowing you to quickly detect and correct problems on the network. 1.2 Features ¾ Complies with IEEE802...

Page 7 - Mounting the Switch in a Rack; Figure 2-1 Rivet the ‘L’brackets onto the Switch

3 2.2 Mounting the Switch in a Rack The dimension of TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 is designed according to the standard 19'' rack- mountable steel case of Electronic Industries Association. Turn off all the equipment connected to the Switch before mounting it in the rack, then rivet the t...

Page 8 - Power on; represents a resetting of the system.; Chapter 3 Identifying External Components; Front Panel; Figure 3-1 TL-SL1351 Switch Front Panel sketch

4 2.3 Mounting the SFP Module (for TL-SL1351 Only) The front panel of the TL-SL1351 consists of a SFP module, which support The Hot Plug- And- Draw. Should fixed the SFP into SFP pluggable when use the SFP module. The switch could identify and configure the SFP module automatically. 2.4 Power on TL-...

Page 9 - Rear Panel; Figure 3-2 TL-SL1351 Switch Rear Panel sketch

5 ¾ 1000M LED: The corresponding gigabit port LED indicator will light solid green when the gigabit port connected to a 1000Mbps device. It flashes green when data is being transmitted or received on the working connection. ¾ 100M LED: The corresponding 100M port LED indicator will light solid green...

Page 10 - Appendix A: Specifications; General; Standards

6 Appendix A: Specifications General IEEE802.3 10Base-T IEEE802.3u 100Base-TX IEEE802.3ab 1000Base-T IEEE802.3z 1000Base-X (for TL-SL1351 only) Standards ANSI/IEEE Std 802.3 Nway IEEE802.3x Protocol CSMA/CD Ethernet: 10Mbps (Half Duplex), 20Mbps (FullDuplex) Fast Ethernet: 100Mbps (Half Duplex), 200...

Page 11 - Environmental and Physical; Storage Temperature

7 Uplink Ports Auto MDI/MDI-X cable detection, Each port can be used Uplink ports Transfer Method Store-and-Forward MAC Address Table 8k, Automatically learning, automatically Update 10Base-T: 14880pps/Port 100Base-TX: 148810pps/Port Frame Filter Rate 1000Base-T: 1488095pps/Port 1000Base-X: 1488095p...