TP-Link TL-SC3430 - Manuals

ii 7.1.3 Initialize ................................................................................................................... 28 7.1.4 Language ................................................................................................................ 29 7.2 Camera ......................

iii B.1 Mega Mode ..................................................................................................................... 78 B.2 VGA Mode ....................................................................................................................... 80 C. System Requirement – H...

1 Package Contents The follow items should be found in your package: ¾ TL-SC3430 H.264 Megapixel Surveillance Camera ¾ Power Adapter ¾ Mounting Bracket with three screws, a Lock Ring, a Brace and a Base Plate ¾ RJ45 Cable ¾ Quick Installation Guide ¾ Resource CD, including: z This User Guide z Aplli...

2 Chapter 1 Safety Instructions ¾ Before you use this product This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if not used properly. To avoid such accidents, be sure to heed the following. ¾ Legal Caution Video...

3 Chapter 2 Minimum System Requirement & Product Feature 2.1 System Requirement For normal operation and viewing of the network camera, it’s recommended that your system meet these minimum requirements for proper operation: Item Requirements CPU Pentium 4 2.8GHz (or equivalent AMD) Graphic Card ...

4 Two-way (full / half duplex) with built-in microphone Audio Audio compression: G.711 μ law, a law, and AMR Instant Messenger Support MSN Live View Mobile Phone Live View Through 2.5 WAP, 3GPP, 3G Streaming, and 3G Browser Alarm Sending FTP Client / SMTP / Network Storage Security Passward Protecto...

6 Chapter 3 Using IP Camera via Web Browser 3.1 Obain the IP Address 1. Insert the provided CD into your CD-ROM driver. The Setup Wizard will automatically pop up on your computer’s screen as shown in the figure below. Figure 3-1 2. Choose the Intelligent IP Installer , and then the next screen appe...

7 Figure 3-2 3. After the installation is finished, click Start > All Programs > TP-LINK >Intelligent IP Installer to start using the program. Figure 3-3 4. The following screen will then display. Click the Search button to search Network Cameras in the network; it displays Network Cameras ...

8 Figure 3-4 3.2 Windows Web Browser 1 Click Link to IE button in Figure 3-4 or launch your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser. ) Note: If you only want to view the video without accessing Setting screen, enter “http://...

9 3 The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup. For more details, you can check Chapter 6.2 、 Chapter 6.3 、 Chapter 6.4 and Chapter 6.5. 3.3 Mac Web Browser 1 Click the Safari icon, and enter the IP add...

10 2 Enter the default account “ admin ” and default password “ admin ”.

12 Chapter 4 Operating IP Camera via Mobile Phone 4.1 Mobile Phone Viewing 4.1.1 3G Mobile Phone Streaming Viewing For 3G mobile phone viewing, type “ rtsp://<IP>:<PORT>/video.3gp ” into your 3G Streaming Link. <IP> is the Public IP address of your IP camera; <PORT> is the RT...

13 4.2 Using IP Camera via iPhone You can use TP-LINK Web User Interface via iPhone. Please follow the setting process below. Then you can use TP-LINK Web UI via iPhone. 1. Select Safari function 2. Enter IP address in your web link. 3. Enter name and password. Default values are both admin. Then cl...

14 Chapter 5 MSN Messenger Please see the following steps to set up the Messenger function. 1. Application of a new MSN account: You can download MSN software freely and create a new MSN account (e.g. camera at [email protected]) to use Microsoft Live Messenger. 2. Login Account and Password: Go to Setti...

15 4. Privacy & User & Allow List: Choose “ On ” at the option of Privacy, then User column will appear and be able to build Allow List, so that only the users listed can access the camera via MSN. 5. Log in Working Account: Use your working account to login in the Messenger software. And ad...

16 7. The Camera at home will show up with its Public IP and Private IP after sending a message of “ Ping ” in the lower key (if the option of IP Notification is “On”). 8. Click the camera icon and select View a contact’s webcam to view the video.

17 9. The IP Camera will accept your invitation; the live video will show up in the right screen after few seconds. 10. Click Action button and choose Start Control Panel to use control panel.

18 11. The dialog box will show up with “This application is not part if Window Live Message…….” Tick the box of “Don’t show me this again” and click OK . 12. The IP Camera will accept your invitation to start Control Panel.

19 13. You can click Camera icon to snapshot then the picture will send to you immediately. 14. You can click paint palette icon showing up with tool bar to set up image. Then, you can use the tool bar to optimize video Brightness , Contrast , Saturation and Hue . After the adjustment of all setting...

21 Chapter 6 Configuration of Main Menu In the left side of main configuration are Setting, Client setting, Image setting. For more details, please check Chapter 6.2 、 Chapter 6.3 、 Chapter 6.4. 、 Chapter 6.5. In the right side, you can control Live View in your main Browser. The functions include: ...

22 6.1.2 Digital zoom in / out the image via the monitor window • Click to display the digital zoom in window. • Pull the to adjust the digital zoom range, and it will be showed on the above window. • Use the left click of your mouse to move to anywhere in the window area. 6.1.3 Video play buttons S...

24 6.3 Client Setting This function is only for the client. Click this button to control Mode, View Size, Protocol, and Video Buffer. 6.3.1 Mode Click the pull-down box to choose video compression mode of LIVE VIEW among H.264, MPEG-4, and MJPEG. ) Note: As long as the operating system not able to a...

26 Chapter 7 Setting-Basic Click the Basic folder to display the sub folders including System, Camera, Network, and Security. 7.1 System Click the folder of System to display the sub-folders including Information, Date / Time, Initialize, and Language. 7.1.1 Information The Information screen provid...

27 7.1.2 Date / Time The Date/ Time screen displays all options of time setting. ¾ Current Date / Time: This displays the current date and time of this IP Camera. ¾ PC Clock: This displays the date and time of the monitoring PC clock. ¾ Date / Time Format: You can click the pull down box to select d...

29 7.1.4 Language ¾ Upload Language Pack : Clicking “Browse” and selecting the file for updating, the present language display of WEB User Interface could be changed. A confirmation dialogue will appear. Click “OK”, then the update will be applied immediately. The default language is “English.” 7.2 ...

30 7.2.1 General ¾ RTSP : The default value is 554. If the IP Cameras connected with router and installed outside are over 2 sets and all of them need support RTSP, please fill some value in the blank space in the range from 1024 to 65535. ¾ RTP Unicast Streaming : The default value of port range is...

31 z H.264: H.264 provides higher compression rate than MPEG-4. Thus, H.264 can decrease the bandwidth usage and further apply on 3G. However, H.264 will occupy more system resources than MPEG-4. As long as the operating system appears operating difficulties under H.264 format, please change to sele...

32 network routers that can be passed before data arrives at its destination or is dropped) within which a multicast packet must reach its destination. ¾ Image Size : Specify the image size when the network camera transmits. Choose one among 1280 x 1024, 1280 x 720, 640 x 480, and 320 x 240. ¾ Frame...

33 7.2.3 MPEG4 ¾ Viewer Authentication: z On : If the viewer authentication is On, the users will be requested to key-in username and password when using QuickTime Player to have live viewing. z Off: If the viewer authentication is Off, you can have live viewing on computer by QuickTime Player after...

34 ) Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480. However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the same time. ¾ Quality: z Auto: The quality and bitratee will ...

35 7.2.4 MJPEG ¾ Viewer Authentication: z On : If the viewer authentication is On, the users will be requested to key-in username and password when using QuickTime Player to have live viewing. z Off: If the viewer authentication is Off, you can have live viewing on computer by QuickTime Player after...

36 selected 320x240 or 640x480 at the same time. ¾ Quality: z Auto: The quality and bit rate will be adjusted automatically according to the frame rate. z Fixed Quality: Select the value of quality among Medium, Good, Delicate and Excellent. z Fixed Bitrate: Set the bitrate of MJPEG image transmissi...

39 7.3 Network Click the folder of Network to display the sub folders including Information, PPPoE, DDNS, UPnP, Bonjour, IP Notification and Messenger . Full Screen Mirror/ Flip Snapshot Open Digital Zoom Volume Mute on / Mute off Increase Speed Decrease Speed Open Files Stop Pause

42 z Primary DNS server: Enter the IP address of the primary DNS server. z Secondary DNS server: Enter the IP address of the secondary DNS server. ) Note: 1) PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network protocol for encapsulating Point-to-Point Protocol frames insider Ethernet f...

43 ¾ Server Name : Choose the DDNS Server from the list. ¾ User ID : Enter the user ID for authentication necessary for DDNS connections. Type it up to 64 characters. ¾ Password : Enter the password for authentication necessary for DDNS connections. Type it up to 32 characters. ¾ Re-type Password : ...

44 2. Input all information and follow step by step with DynDNS. 3. Login with new account and click Account → My Hosts → Add Host Services.

45 4. Type domain in the Hostname field and select sub-domain. 5. After typing information, check your DDNS service

46 6. Type your DDNS User ID, Password and Host name in Setting → Network → DDNS . After completing setting, reboot IP Camera. 7.3.4 UPnP (Universal Plug and Play) If you have a Router to access to internet and the Router supports UPnP IGD function, you need to turn on the UPnP Port Forwarding funct...

47 ¾ HTTP Port : Enter the HTTP port number and default HTTP port is 80. ¾ SSL Port: Enter the SSL port number and default SSL port is 443. ¾ RTSP Port: Enter the RTSP port, default value is 554 for computer view. ) Note: UPnP (Universal Plug and Play): UPnP is a set of computer network protocol. It...

48 ¾ Device Name : Enter Device Name you wish. ) Note: How to use Bonjour in your Windows Browser UI? Please check the link below:

50 z SMTP: Select if SMTP authentication is necessary when an e-mail is sent. z POP before SMTP : Select if POP before SMTP authentication is necessary when an e-mail is sent. 9 POP server name : It is necessary when the POP before SMTP is selected in Authentication . Type the POP (receiving mail) s...

52 7.4 Security Click the folder of Security to display the sub folders including Account and HTTPS. 7.4.1 Account The device fault account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a...

54 ) Note: When enable HTTPS with RTSP on mode, the IP Camera only protect the setting such as username and password and do not protect video and audio. When enable HTTPS with RTSP off mode, the IP Camera will protect all setting including video and audio. 7.4.3 IP Filter IP Filter provides the func...

55 list. ¾ Allow Range List: Except the default range 0.0.0.0~255.255.255.255, the list allows to add four more sets of allow range at most. ¾ Deny Range: You can define the deny range by entering “Start IP address” and “End IP address” ¾ Deny Range List : You can define not more than five sets of d...

56 Chapter 8 Setting-Advanced Click the folder of Advanced to display the sub folders including FTP client, SMTP, Network storage, Schedule, Alarm buffer, Motion detection, Audio detection , and System Log . 8.1 FTP Client Use this menu to set up for capturing and sending a image or video clip to an...

64 ¾ Image File Name : Type the file name of the image sent by SMTP up to 10 alphanumeric characters, - (hyphen) and _ (under score). ¾ Suffix : Select a suffix to be added to the file name sent by SMTP. z Date & time : The date & time suffix is added to the Image file name. The date & t...

65 8.3.1 General Select On if you would like to use the network storage function. Then choose one protocol between Windows network (SMB/CIFS) and Unix network (NFS). ¾ Protocol- Unix Network (NFS): z Network storage location: Type the IP or name of specified computer and folder. For example, //IP/fo...

70 Use alarm buffer function for recording audio and video file in the IP Camera before and after disconnected network. After re-connecting, these files will transmit to FTP client, SMTP, and Network storage. You can set the pre-alarm and post-alarm period up to 5 seconds in Alarm Buffer function sc...

72 Click it on for using Audio Detection function as a sensor. You can set audio detection function at the audio detection function screen. ¾ Threshold : It means the extent which the alarm will be triggered. The default value is 50 and the value range is 0~100. The larger the value, the higher the ...

73 ¾ Enable Remote Log : Enables user to send the log data to a specified log server.

74 Chapter 9 Appendix A. Frame-rate and Bitrate Table – Help to set IPCamera with your network environment to access Internet. Base on your network upload environment to choose the suitable Image-Quality setting. For example, if the network environment is ADSL 256Kb (upload) / 2Mb (download), the mo...

78 640*480 2048 30 2200 30 640*480 2048 15 2200 15 640*480 512 30 550 30 640*480 512 15 550 15 320*240 6144 30 5100 30 320*240 6144 15 2800 15 320*240 2048 30 2200 30 320*240 2048 15 2200 15 320*240 512 30 550 30 320*240 512 15 550 15 A.2.7 MJPEG @ 30fps / kbps Quality 640*480 320*240 Excellent 1300...

82 320*240 512 15 550 45.7 C. System Requirement – Help to setup System C.1. 16 Channel IPCamera with CIF Performance Equipment Configuration Software: MainConsole Version 2.6.4 Professional CPU: Intel Core 2 Quad Q6600 @ 2400 MHz Memory: 1024 MB (2 x 512 DDR2-SDRAM ) Ethernet: Marvell Yukon 88E8052...

83 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: Clause De...

86 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential i...