TP-Link Tl-SB2216 - Manuals

01 Gigabit Smart Switch Introduction Introduction ChaCter C Product Overview C1C TP-LINK Gigabit Smart Switch, designed for workgroups and departments, provides wire-speed performance and abundant layer 2 management features. It provides a variety of service features and multiple powerful functions ...

02 Gigabit Smart Switch The front panel of TL-SG2424 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port SFP Port Reset Front Panel of TL-SG2424 Figure 1-2 Reset Press this button for five seconds or above to reset the software setting back to factory default settings. LEDs LED Status I...

03 Gigabit Smart Switch Introduction The front panel of TL-SG2424P is shown as the following figure. Reset LEDs 10/100/1000Mbps RJ45 Port SFP Port LED Mode Switch Button Front Panel of TL-SG2424P Figure 1-3 LEDs TL-SG2424P has an LED mode switch but ton which is for switching the LED status indicati...

04 Gigabit Smart Switch Introduction LED Status Indication PoE Max On The remaining PoE power ≤ 7W Flashing The remaining PoE power keeps ≤ 7W after this LED is on for 2 minutes Off The remaining PoE power ≥ 7W 10/100/1000Mbps Green On The port is supplying power normally Flashing The supply power e...

05 Gigabit Smart Switch LED Status Indication 10/100/1000Mbps Green On A 1000Mbps device is connected to the corresponding port, but no activity Flashing Data is being transmitted or received Yellow On A 10/100Mbps device is connected to the corresponding port, but no activity Flashing Data is being...

06 Gigabit Smart Switch The rear panel of TL-SG2424 is shown as the following figure. Grounding Terminal Power Socket Rear Panel Figure 1-6 of TL-SG2424 The rear panel of TL-SG2424P is shown as the following figure. Grounding Terminal Power Socket Rear Panel Figure 1-7 of TL-SG2424P The rear panel o...

07 Gigabit Smart Switch Installation ChaCter 1 Package Contents 11C Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Resource CD One Switch One Power Cord This Installation Guide Two mounting brackets and ...

08 Gigabit Smart Switch Site Requirements ■ Temperature/Humidity ȭ ȭ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of th...

09 Gigabit Smart Switch Lightning Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000 ℃ . As this instant current is strong enough to damage electronic devices, more effective light...

10 Gigabit Smart Switch Product Installation 112 Desktop Installation ■ To install the device on the desktop, please follow the steps: Set the device on a flat surface strong enough to support the entire weight of the 1. device with all fittings. Remove the adhesive backing papers from the rubber fe...

11 Gigabit Smart Switch Rack Rack Installation Figure 2-3 Caution: Please set 5~10cm gaps around the device for air circulation. ■ Please avoid any heavy thing placed on the device. ■ Please mount devices in sequence from the bottom to top of the rack and ensure a ■ certain clearance between devices...

12 Gigabit Smart Switch Lightning Protection ChaCter 2 Cabling Reasonably 21C In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to d...

13 Gigabit Smart Switch Requirements for Cabling Indoors ■ When cabling indoors, keep a certain distance away from the devices that may cause high-frequenc y inter ferences, such as down-conduc tor cable, powerline, power transformer and electromotor. The main cable should be paved in the metal race...

14 Gigabit Smart Switch Cable Pave Way Min Parallel Length (mm1 2~5kVA powerline Parallel cabling 300 One is in the grounded metal raceway or metal pipe 150 The both are in the grounded metal raceway or metal pipe 80 >5kVA powerline Parallel cabling 600 One is in the grounded metal raceway or met...

15 Gigabit Smart Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. Connecting to the Ground via the Power Supply ■ If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth1...

16 Gigabit Smart Switch Grounding Terminal Equipotential Bonding CableGrounding Bar Ground Cable Equipotential Bonding Figure 3-3 When equipotential bonding, please note that the cable should be copper wrapped Kelly with its area being 6mm 2 at least. The shorter cable the bet ter, and use a groundi...

17 Gigabit Smart Switch The port rate of the signal lightning arrester should match the rate of the desired ■ port on the device. If it is not matched, this signal lighting arrester will not work. Purchase a standard lightning arrester. Install signal lightning arrester near the protected device and...

18 Gigabit Smart Switch Connection ChaCter 2 Ethernet Port 21C Connect a Ethernet port of the Switch to the computer by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable Connecting the RJ45 Port Figure 4-1 SFP Port 211 Connect the SFP port to a SFP module. If an SFP transceiver (purchas...

19 Gigabit Smart Switch Connection Verify Installation 212 After completing the installation, please verify the following items: There are 5~10cm of clearance around the sides of the device for ventilation and ■ the air flow is adequate. The voltage of the power supply meets the requirement of the i...

20 Gigabit Smart Switch Configuration ChaCter 4 Configure the Switch via GUI 41C To access the GUI of the Switch, open a web browser and t ype the default 1. management address http://192.168.0.1 in the address field of the browser, then press the Enter key. Web Browser Figure 5-1 Note: To log on to...

21 Gigabit Smart Switch Main Page of the Switch Figure 5-3 Configure the Switch Using CLI 411 You can log on to the Switch and access the CLI by Logging on to the Switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the followin...

22 Gigabit Smart Switch Configuration Type cmd in the prompt Run window as Figure 5-5 and click OK. 3. Run Window Figure 5-5 Type telnet 192.168.0.1 in the command prompt shown as Figure 5-6, and press the 4. Enter button. Connecting to the Switch Figure 5-6 Note: TL-SG2452 is unaccessible through T...

23 Gigabit Smart Switch Troubleshooting ACCendix A Troubleshooting What could I do if I forgot the username and Cassword of the QQQ Switch? Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and...

24 Gigabit Smart Switch ACCendix B Hardware SCecifications Item Content Standards IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX/100Base-FX IEEE 802.3ab 1000Base-T IEEE 802.3z 1000Base-X IEEE 802.3x Flow Control IEEE 802.3af (for TL-SG2424P only1 IEEE 802.3at (for TL-SG2424P only1 Transmission ...

25 Gigabit Smart Switch Technical Support ACCendix C Technical SuCCort For more troubleshooting help, please go to: www.tp-link.com/support/faq ■ To download the latest Firmware, Driver, Utility and User Guide, go to: ■ www.tp-link.com/en/support/download For all other technical support, please cont...