TP-Link NC200 - Manuals

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮，請勿將水或其他液體潑灑到本產品上。  ●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам,...

TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: Cloud Camera, 300Mbps Wi-Fi Model No.: NC200 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product wi...

NC200 Cloud Camera, 300Mbps Wi-Fi CONTENTS Chapter 1 About this Guide .................................................................................... 2 1.1 Conventions ................................................................................................................... 2 1.2 Overv...

NC200 Cloud Camera, 300Mbps Wi-Fi Chapter 1 About this Guide This User Guide contains information for setup and management of NC200 Cloud Camera, 300Mbps Wi-Fi. Please read this guide carefully before operation. 1.1 Conventions In this Guide the following conventions are used:  The camera or NC200 ...

NC200 Cloud Camera, 300Mbps Wi-Fi Chapter 2 Introduction Thanks for choosing the NC200 Cloud Camera, 300Mbps Wi-Fi! 2.1 Overview NC200 is a versatile solution for home & office monitoring to keep an eye on your home, kids or workplace; whatever it is that you care for most. NC200 has a complete ...

NC200 Cloud Camera, 300Mbps Wi-Fi 2.3 Appearance Description 2.3.1 Front Panel Figure 2-1 Front Panel  Microphone: The camera has a built-in internal microphone. This microphone is hidden in the pinhole located on the front panel.  System LED: Status Indication Flashing Red The camera starts booti...

NC200 Cloud Camera, 300Mbps Wi-Fi  Used as RESET button: With the camera powered on, press and hold the WPS/RESET button (more than 5 seconds) until both the System LED and WPS LED turn off. Then release the button and wait the camera to reset to its factory default settings.  Used as WPS button: ...

NC200 Cloud Camera, 300Mbps Wi-Fi Chapter 3 Managing the Camera The camera’s built-in web management page is designed to allow you to easily access and configure your camera. Use the management IP address of the camera to log in to the camera. You can find the IP address in two ways:  Run the Setup...

NC200 Cloud Camera, 300Mbps Wi-Fi Symbols Meaning Note Click to capture a still image shot by the camera. The image file will be saved in JPG or BMP format in your local computer. The file is named as image-yyyy-mm-dd-hh-mm-ss.jpg. You can select a save path and rename the image file. Click to recor...

NC200 Cloud Camera, 300Mbps Wi-Fi Drag the slider to adjust the size of the current image. The maximum zoom ratio is 4 times. Mute off. You can hear the current sound by the camera. Click and it will become . Mute on. The current sound by the camera is turned off. Click and it will become . Drag the...

NC200 Cloud Camera, 300Mbps Wi-Fi 3.3.2 Basic → Network On this page, you can configure your camera’s IP address which is used to access and configure the camera.  Dynamic IP: Select this option when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP...

NC200 Cloud Camera, 300Mbps Wi-Fi Click Save to save and enable the settings. 3.3.3 Basic → Wireless Connection The camera’s wireless function is enabled by default. This function helps to connect your camera to a wireless network wirelessly. If you don’t want to use this function, just select the D...

NC200 Cloud Camera, 300Mbps Wi-Fi You can select Show password to display what you’ve entered. 4. A pop-up screen will prompt you for the network modification. Click Change to continue. 5. Click OK on the pop–up screen to finish wireless connection procedure. 15

NC200 Cloud Camera, 300Mbps Wi-Fi 6. To start using camera wirelessly, unplug its Ethernet cable. 3.3.4 Basic → Cloud Settings NC200 is a Cloud Camera which can be viewed anytime and anywhere over the Internet with TP-LINK Cloud service. On this page, you can add your camera to an existing TP-LINK C...

NC200 Cloud Camera, 300Mbps Wi-Fi an easy-remember one. Camera name can contain up to 30 characters. It can only contain digits, letters, space and .-_@'. After your camera is registered successfully, you can go to www.tplinkcloud.com to view it. Sign Up for a TP-LINK Cloud Account If you do not hav...

NC200 Cloud Camera, 300Mbps Wi-Fi Connection , Wireless Extender , Cloud Setting , DDNS , Video , Motion Detection , Notification Sending , and LED . 3.4.1 Advanced → Status Refer to 3.3.1 Basic → Status . 3.4.2 Advanced → Network On this page, you can configure your network settings. 18

NC200 Cloud Camera, 300Mbps Wi-Fi IP Address On this page, you can configure your camera’s IP address which is used to access and configure the camera.  Dynamic IP: Select this option when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address of...

NC200 Cloud Camera, 300Mbps Wi-Fi  Static IP: Select this option when a static or fixed IP address is obtained for the camera. A static IP address will ease your access to the camera in the future. Add your camera’s static IP information to your router to avoid IP conflicts.  MAC Address: Displays...

NC200 Cloud Camera, 300Mbps Wi-Fi  PPPoE: To enable or disable the PPPoE service here.  Status: Displays the PPPoE connection status.  Username: Enter the username for PPPoE service provided by your ISP.  Password: Enter the password for PPPoE service provided by your ISP. HTTP (Hypertext Transf...

NC200 Cloud Camera, 300Mbps Wi-Fi Bonjour Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter ...

NC200 Cloud Camera, 300Mbps Wi-Fi 1. Select Enable to enable your camera’s wireless function. 2. Click Manually , and you will see the following screen. 3. In the Wireless Network Name field, enter the name of the wireless network to which your camera is ready to connect.  Note: The name must be ex...

NC200 Cloud Camera, 300Mbps Wi-Fi wireless network. 5. Click Connect and a screen will pop up. Click Change on the pop-up screen. 6. Click OK on the pop–up screen to finish wireless connection procedure. 7. To start using camera wirelessly, unplug its Ethernet cable. 3.4.4 Advanced → Wireless Extend...

NC200 Cloud Camera, 300Mbps Wi-Fi  Max Clients: Set the maximum number of clients that are allowed to connect to the extended network. Click Save to save and enable the settings. 3.4.5 Advanced → Cloud Settings Refer to 3.3.4 Basic → Cloud Settings . 3.4.6 Advanced → DDNS If your camera is connecte...

NC200 Cloud Camera, 300Mbps Wi-Fi ( www.noip.com ), DynDNS ( www.dyn.com ), and Comexe ( www.comexe.cn ).  Note: If you have not registered for any of the listed DDNS servers, please select one and click Go to register… and follow the instructions provided on the official website to register.  Use...

NC200 Cloud Camera, 300Mbps Wi-Fi  Time Stamp: If enabled, the current time of your camera, which can be set on System → Date/Time page, will be displayed on the top right corner of the live view screen. With this feature enabled, you can find out the exact time of the snapshot or record easily.  ...

NC200 Cloud Camera, 300Mbps Wi-Fi  Motion Detection: To enable or disable the motion detection function here.  Sensitivity: Specify the level of difference between two sequential images that would indicate motion. Select one of the three levels of sensitivity from the drop-down list: High, Medium,...

NC200 Cloud Camera, 300Mbps Wi-Fi FTP Select FTP , you can configure your camera to send snapshots to a specified FTP sever on the following screen:  FTP Server/ Port: Enter the IP or the domain (IP/domain without prefix ftp://) and the port of the FTP server that you will be connecting to. The por...

NC200 Cloud Camera, 300Mbps Wi-Fi 1. Enter an IP address or domain of your FTP server, e.g. 192.168.1.168 2. Remain the FTP port number as the default value: 21. 3. Enter your username to log in to the FTP server, e.g. test. 4. Enter your password to log in to the FTP server. 5. Enter the path to th...

NC200 Cloud Camera, 300Mbps Wi-Fi E-mail Select E-mail , you can configure your camera to send snapshots to a specified E-mail address on the following screen.  Recipient E-mail Address: Enter the receiver’s E-mail address that the notification E-mail will be sent to. Click Add recipient to add rec...

NC200 Cloud Camera, 300Mbps Wi-Fi  Note: If TLS is selected as the SSL Encryption, set the Sender E-mail Port as 465; if STARTTLS is selected, set the Port as 25 or 587.  Sending Interval: Set the limit for how frequently E-mail notifications will be sent. Select one interval from the drop-down li...

NC200 Cloud Camera, 300Mbps Wi-Fi If the settings are tested incorrect, you will see the following screen. Click OK . Please check your network and E-mail settings and try again later. 3.4.10 Advanced → LED Refer to 3.3.5 Basic → LED . 3.5 System Click the System folder to display the sub folders in...

NC200 Cloud Camera, 300Mbps Wi-Fi are allowed to access to your camera.  Username: Displays the name of user account.  User Group: Displays the group the user account is in. Different user group has different limits of authority.  admin: Admin group has all authority of configuration. It can only...

NC200 Cloud Camera, 300Mbps Wi-Fi You can delete a user account except admin here. Select one in the list and click Delete . 3.5.2 Date/Time On this page, you can configure the settings of the internal system clocks for your camera.  Current Time: Displays the current date and time of the camera. ...

NC200 Cloud Camera, 300Mbps Wi-Fi 2. Click Browse to locate the latest downloaded software. 3. Click Upgrade to update the camera’s software to the latest version. 4. Wait for the uploading process to complete, and the camera will reboot automatically.  Note: 1. We recommend you to use a wired conn...

NC200 Cloud Camera, 300Mbps Wi-Fi  Time: Displays the time when the log event occurs. The log can get the correct time after you configure on the Date/Time page. (go to Advanced → Date/Time )  Module: Displays the module to which the log information belongs. You can specify the module by selecting...

NC200 Cloud Camera, 300Mbps Wi-Fi Appendix A: Specifications SYSTEM Image Sensor 1/4’’ Progressive scan CMOS sensor Resolution 0.3 Megapixel (640*480) Lens F: 2.8, f: 3.85mm Viewing Angle FOV=64 ° Digital Zoom 4x Digital Video/Image Video Compression MJPEG Frame Rate & Resolutions Max: 20 fps at...

NC200 Cloud Camera, 300Mbps Wi-Fi Appendix B: Troubleshooting Question Answer or Resolution Features The maximum number of users accessing the camera simultaneously. The maximum number of users is limited to 13. However, it also depends on the total bandwidth accessed to this camera from clients. Th...

NC200 Cloud Camera, 300Mbps Wi-Fi router check user’s manual of router and turn on UPnP function.  Maybe UPnP function of NAT router is not compatible to the IP camera. Please contact your dealer to get the approval routers list. Some cameras are working but others are failed  Maybe too many camer...