TOA HX-5B - Manuals - manualsarea.com

Page 2 - When Installing the Unit; SAFETY PRECAUTIONS; Safety Symbol and Message Conventions; WARNING

2 When Installing the Unit • Refer all installation work to the dealer from whom the speaker was purchased. Installation for flying requires extensive technical knowledge and experience. The speaker may fall off if incorrectly installed, resulting inpossible personal injury. • Flying Precautions Be ...

Page 3 - When the Unit is in Use; CAUTION; GENERAL DESCRIPTION

3 When Installing the Unit • Avoid touching the unit's sharp metal edge to prevent injury. • To avoid electric shocks, be sure to switch off the unit's power when connecting speakers. When the Unit is in Use • Do not place heavy objects on the unit as this may cause it to fall or break which may res...

Page 4 - ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITRY; Caution

4. ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITRY The speaker system features internal input overload protection circuitry. If an extremely high input level is fedto the unit, the protection circuitry automatically cuts off the signal to the tweeters. A drastic reduction in sound volume for the high ...

Page 5 - DIMENSIONAL DIAGRAM; CHANGING THE ORIENTATION OF REAR PLATE

5 6. DIMENSIONAL DIAGRAM [Top] [Front] • HX-5B/5W Input Section • HX-5B-WP/5W-WP Input Section [Side] [Rear] 408 (16 1/16 ) 342 (13 15/32 ) 546 (21 1/2 ) Unit: mm (inches) Rear plate Input section Screw terminals Speaker cable(60 cm or 23 5/8 in. long) SpeakonNL4MP connector Figures show the HX-5 se...

Page 6 - Note

8. INPUT SECTION 8.1. HX-5B and HX-5W • The 2 Speakon connectors are internally connected in parallel to the screw terminals; you can use either one. • T h e r i g h t t a b l e s h o w s t h e p i n a r r a n g e m e n t o f t h e Speakon NL4MP connector. • The usable connector (on the cable end) f...

Page 7 - CHANGING THE SPEAKER'S DIRECTIVITY ANGLE

7 9. CHANGING THE SPEAKER'S DIRECTIVITY ANGLE The speaker system's directivity angle mode is factory-preset to 60°,but this mode can be changed to 45°, 30°, or 15° by following theprocedure described below. The figure on the right shows the speaker system in 60° mode. Step 1. Loosen the 2 bolts on t...

Page 9 - SUSPENDED INSTALLATION

9 10. SUSPENDED INSTALLATION The speaker systems may be suspended either vertically or horizontally. Step 1. For vertical suspension: Remove the speaker grill on the module to be suspended. (Below, upper) For horizontal suspension: Remove the speaker grills on the modules at both ends of the speaker...

Page 13 - DIRECT WALL MOUNTING

[Direct wall mounting dimensions] (Angle mode of 60 ° ) 408 (16 1/16 ) 131 (5 5/32 ) 4-12 x 41 (4- 15/32 x 1 39/64 ) 546 (21 1/2 ) 181 (7 1/8 ) 6 ( 15/64 ) 23 ( 29/32 ) Unit: mm (inches) Rear plate Speaker system [Direct wall mounting dimensions] (Angle mode of 60 ° ) Unit: mm (inches) 546 (21 1/2 )...

Page 14 - MOUNTING BRACKET TYPES; • Speaker Stand Adapter HY-ST1

14 12. MOUNTING BRACKET TYPES The following mounting brackets are optional. Consult the instruction manual enclosed with each bracket for details on their installation and use. • Speaker Rigging Frames HY-PF1B, HYPF1W, and HY-PF1WP Can be used to suspend the speaker system from high ceilings. • Spea...

Page 16 - • Accessories

Printed in Indonesia 533-06-125-50 15. SPECIFICATIONS Note: The design and specifications are subject to change without notice for improvement. • Accessories Suspension bracket .................................... 2Hex head wrench ....................................... 1 Model No. HX-5B HX-5W HX-5B...