TOA H-1 - Manuals - manualsarea.com

Page 2 - SAFETY PRECAUTIONS; Safety Symbol and Message Conventions; WARNING; CAUTION; When the Unit is in Use

1. SAFETY PRECAUTIONS • Be sure to read the instructions in this section carefully before use. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. • We also recommend you keep this instruction m...

Page 3 - GENERAL DESCRIPTION; ensures powerful sound reproduction.; applications. For low-impedance applications, either the 4; can be easily changed from outside the unit.; HANDLING PRECAUTIONS; CRTs to avoid degradation in picture quality.

2. GENERAL DESCRIPTION TOA's H-1 is a cylinder-shaped, small flush-mount 2-way speaker featuring high sound quality. 3. FEATURES • The H-1 Speaker System features, flush-mount speaker design with a rotatable cylinder-type enclosure. The speaker's smooth curved surface allows it to blend in with the ...

Page 4 - For mounting to the Adapter Panel

5. NOMENCLATURE [Side Panel] [Front Panel] [Side Panel] H-1 speaker Grille Trim Piece [Side Panel] [Rear Panel] For mounting to the Adapter Panel Mounting bracket For mounting to an electrical box Accessory (Adapter Panel) 4

Page 5 - Direct Wall/Ceiling Mounting Without Using an Electrical Box; Step 1. Adapter Panel mounting; -1. Using the supplied hole pattern sheet as a guide,

6. INSTALLATION 6.1. Direct Wall/Ceiling Mounting Without Using an Electrical Box Step 1. Adapter Panel mounting 1-1. Using the supplied hole pattern sheet as a guide, make an opening of the specified size in the wall or ceiling panel. Note The thickness of the suitable wall or ceiling panel is 9to ...

Page 6 - Step 2. Wiring and impedance changes; -3. Insert the stripped cable ends into the input; Note; vibration or rattling noise.; connections

1-4. Clamp the wall or ceiling panel using the two board clamps, and secure with the clamp screws. Step 2. Wiring and impedance changes 2-1. Pull the cables out of the mounting hole in the wall or ceiling, then strip the insulation back about 5mm from the cable ends. Note Usable cable: Solid cable o...

Page 7 - Impedance selector socket; Step 3. Mounting the speaker and Trim Piece; A d a p t e r Panel mounting tabs, then mount the; Adapter Panel

2-4. Attach two impedance s e l e c t o r s o c k e t s to the connector to select the desired impedance. Preset to 830 (12 W for 100 V line and 6 W for 70 V line). Note The speaker is designed to be used for both 70 V and 100 V line applications. When using the 100 V line, do not select the "42...

Page 8 - Tip; angles at 15 ° intervals, use this marking as a guide; the speaker's two stud screws, then push the Trim; Trim Piece; Memo; Electrical box; Adapter Panel

Stud screw 3-2. Loosen the angle adjustment screws. After adjusting the angle, retighten the screws. Tip The mounting angle can be adjusted for up to ± 45 °. Since the mounting bracket is marked with mounting angles at 15 ° intervals, use this marking as a guide when adjusting the angle. Angle adjus...

Page 9 - Mounting the Speaker Directly to an Electrical Box; Electrical box mounting screws are; When removing the Trim Piece for maintenance or repair,; Trim Piece and wall/ceiling, then insert a screwdriver blade; Caution; If you raise either right or left side of the Trim Piece by

6.3. Mounting the Speaker Directly to an Electrical Box The H1 speaker system can also be mounted directly to an electrical box*. Follow Steps 2 and 3 for instructions. In this case, use the outward-facing holes in the mounting bracket when mounting to the wall or ceiling. * Distance between mountin...

Page 10 - REPAINTING THE GRILLE AND TRIM PIECE; Follow the procedures below to change the color of the; Paint both the grille and Trim Piece.; Notes; After the paint has dried, remount the grille to the

Grille 7. REPAINTING THE GRILLE AND TRIM PIECE Follow the procedures below to change the color of the grille. 1. Remove the speaker's angle adjustment screw (1 piece). 2. Detach either of the two mounting brackets attached to the speaker. Mounting bracket Angle adjustment screw Grille mounting screw...

Page 11 - PROTECTION CIRCUITRY INFORMATION; and cuts off the signal input to the speaker component.; Important Note; as shown below, sounds can be made more powerful and intelligible.; PEQ

7. Attach the grille to the speaker with its two mounting screws. 8. Reattach the mounting bracket to the speaker with the angle adjustment screw. 8. PROTECTION CIRCUITRY INFORMATION • The speaker has built-in overload protection circuitry. If there is an extremely high level input signal to the spe...

Page 12 - • Accessories; Pattern paper; Printed in Japan; TOA Corporation; Rated Input

10. SPECIFICATIONS • Accessories Adapter Panel Pattern paper Speaker mounting screw M4 x 25 (with spring washer and plain washer) Electrical box mounting screw M4 x 25 UNC No. 8-32 x 32 mm Spring washer Plain washer Printed in Japan 133-01-413-2A TOA Corporation * 1 Continuous 24 hours, band-limited...