Titan 759-601 - Manuals

Titan 759-601 – Manual in PDF format online.

Manuals:

Manual

Manual Titan 759-601

Summary

Page 2 - CAUTION; WARNING

2 © Titan Tool Inc. All rights reserved. Table of Contents Introduction ................................................................................2 Gasoline Engine Safety .............................................................3 Safety Warnings ...............................................

Page 4 - Grounding Instructions; Gasoline Engine Safety

4 © Titan Tool Inc. All rights reserved. Grounding Instructions Electric models must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wi...

Page 5 - Specifications; Gasolines Containing Alcohol

© Titan Tool Inc. All rights reserved. 5 Set Up Read, understand, and follow all warnings before starting or operating this sprayer. Required tools: Crescent Wrench 1. One Gun Operation — Attach the gun and hose. Always use a spray hose at least 50 feet long. Do not use PTFE or thread sealant on thi...

Page 6 - Startup; Cleanup; Pressure Relief Procedure

6 © Titan Tool Inc. All rights reserved. Startup 1. Areas must be well ventilated to prevent hazardous operation with volatile solvents or exhaust fumes. 2. Before starting the unit. check oil levels. a. The hydraulic fluid level should read "Full" on the dipstick. CHECK IT REGULARLY. See “H...

Page 7 - Maintenance

© Titan Tool Inc. All rights reserved. 7 5. Close the pressure bleed valve and hold gun trigger open until solvent flows freely from gun. If solvent is not too dirty, recirculate it by flowing gun stream back into solvent container. Use additional clean solvent and repeat procedure if necessary. 6. ...

Page 8 - Airless Tip Selection; Troubleshooting — Airless Gun

8 © Titan Tool Inc. All rights reserved. Airless Tip Selection Tips are selected by the orifice size and fan width. The proper selection is determined by the fan width required for a specific job and by the orifice size that will supply the desired amount of fluid and accomplish proper atomization. ...

Page 9 - Troubleshooting — Spray Patterns

© Titan Tool Inc. All rights reserved. 9 CONDITION POSSIBLE CAUSE CORRECTION TAILS Inadequate fluid delivery. Fluid not atomizing correctly. Increase fluid pressure. Change to smaller tip orifice size. Reduce fluid viscosity. Reduce hose length. Clean gun and filter(s). Reduce number of guns using p...

Page 11 - Español; Seguridad; ADVERTENCIA; PRECAUCION

© Titan Tool Inc. All rights reserved. 11 Español Seguridad Este manual contiene información que debe leer y comprender antes de usar el equipo. Cuando se encuentre con uno de los siguientes símbolos, asegúrese de observar sus indicaciones de seguridad. Este símbolo indica la existencia de un peligr...

Page 12 - Instrucciones para conectar a tierra; Seguridad con los motores de gasolina

12 © Titan Tool Inc. All rights reserved. • Los Estándares de Seguridad del Gobierno de los Estados Unidos se han adoptado bajo el Acta de Seguridad y Salud Ocupacionales (OSHA por sus siglas en inglés). Deben consultarse estos estándares, particularmente la parte 1910 de los Estándares Generales y ...

Page 13 - Français; Sécurité; AVERTISSEMENT; ATTENTION

© Titan Tool Inc. All rights reserved. 13 Français Sécurité Le présent manuel comprend des renseignements devant être lus attentivement avant toute utilisation de l'appareil. Lorsque l'un des symboles suivants apparaît, il est recommandé d'être particulièrement attentif et de tenir compte des mesure...

Page 14 - Instructions de mise à la terre; Sécurité du moteur à essence

14 © Titan Tool Inc. All rights reserved. DANGER: GÉNÉRALITÉS - Peut causer des dommages matériels ou corporels sérieux. MESURES PRÉVENTIVES: • Avant d'utiliser tout équipement, lire attentivement toutes les instructions et les consignes de sécurité • Toujours débrancher le moteur de l’alimentation ...

Page 15 - Parts Lists and Service Instructions; Main Assembly — Gas Model

1 2 3 4 5 6 7 10 8 © Titan Tool Inc. All rights reserved. 15 One Gun Two Guns Item Part # Description 759-600 759-601 1 235-143 Motor/pump assembly ....................................1 ....................1 2 930-515 Filter assembly, outlet manifold......................1 ....................1 3 75...

Page 16 - DC — Electric Convertokit

16 © Titan Tool Inc. All rights reserved. Gas Convertokits (P/N 506-131) Item Part # Description Quantity 1 860-502 Nut, stop ................................................8 2 860-004 Washer, flat ...........................................8 3 980-331 Engine, gas 5.5 HP, Honda ...................1...

Page 17 - Electric Convertokits Service Instructions

© Titan Tool Inc. All rights reserved. 17 Electric Convertokits Service Instructions Before servicing the electric motor, follow the “Pressure Relief Procedure” in the Cleanup section of this manual. Once you have completed this procedure, unplug the power supply cord. Failure to reduce pressure can...

Page 19 - Hydraulic System; Torque and Sealant Guide

© Titan Tool Inc. All rights reserved. 19 Hydraulic System Item Part # Description Quantity 1 420-250 Tubing, PTFE................................................1 2 449-126 Hose clamp ...................................................1 3 431-042 Tube connector ........................................

Page 20 - Hydraulic Motor Service Instructions; Hydraulic Motor

20 © Titan Tool Inc. All rights reserved. Hydraulic Motor Service Instructions Disassembly 1. Disconnect the high pressure hose line from the elbow (32 and 33 in Hydraulic System parts list) on the back of the rotary pump. 2. Remove the two mounting bolts and two lock washers (86 and 32 in Cart Asse...

Page 22 - Connecting Pin Arrangement; Fluid Pump; Fluid Pump Service Instructions

22 © Titan Tool Inc. All rights reserved. 8. Pre-lubricate the piston and valve rod assembly with Coolflo™ hydraulic fluid (P/N 430-361). Install hydraulic piston rod (21) into motor pump block (25) with a gently pushing and rotating motion to work the hydraulic piston rod in through the seal (24). ...

Page 24 - Inlet Accessories

24 © Titan Tool Inc. All rights reserved. Inlet Accessories Bleed Line Assembly with Valve (P/N 840-212) Item Part # Description Quantity 1 944-620 Bleed valve ...........................................1 2 103-117 Tube ......................................................1 3 539-062 Hose assembly ...

Page 25 - Outlet Accessories; 30 Outlet Manifold Filter Assembly with Check

© Titan Tool Inc. All rights reserved. 25 Outlet Accessories 930 Outlet Manifold Filter Assembly with Check Valve 930-514 930-515 930-516 Item Part # Description Qty. Qty. . Qty. 1 930-937 Filter cap assembly .......1 .............1 .............1 2 930-020 Spring ............................1 ........

Page 26 - Second Gun Installation

1 6 16171819 7 89 10 11 12131415 20 5 4 3 2 23 25 2627 28 29 1213 17 23 24 21 22 Second Gun Assembly Complete (P/N 759-038) Item Part # Description Quantity 1 756-029 Block clamp ..........................................1 2 424-288 Cable guide...........................................1 3 756-124 E...

Page 28 - Trigger Assembly; Trigger Selection

28 © Titan Tool Inc. All rights reserved. Line Pointer (P/N 424-620) 1 3 4 2 1 Item Part # Description Quantity 1 424-244 Clamping bolt ........................................2 2 424-257 Clamp ...................................................1 Item Part # Description Quantity 3 424-258 Guide .......

Page 29 - SAE O-Ring Fitting Installation; Accessories and Service Kits; Athletic Field Marking Kit/Turf Kit; Turf Kit Installation

© Titan Tool Inc. All rights reserved. 29 SAE O-Ring Fitting Installation Steps 1 & 2: Step 3: Step 4: Step 5: Cautions: Lubricate Lubricate Tighten nut Recess gap No gap Align Hold this part stationay Avoid screwing fitting in too far. Avoid leaving fitting too far out. Bent washer allows for o...

Page 30 - Notes

Page 32 - Limited Warranty

32 © Titan Tool Inc. All rights reserved. Titan Tool Inc. warrants all equipment manufactured by it and bearing its brand names to be free from defects in material and workmanship at the time of sale by an authorized Speeflo distributor. Titan Tool Inc. will for a period of twelve months (twenty-fou...