Titan 759-2011 - Manuals

Titan 759-2011 – Manual in PDF format online.

Manuals:

Manual

Manual Titan 759-2011

Summary

Page 2 - CAUTION; WARNING; WARNING

Table of Contents Safety Precautions .................................................................2 Français ..............................................................................18Español ...............................................................................20 General Descripti...

Page 3 - Gasoline Engine Safety; Specifications

3. Always use the nozzle tip guard. Do not spray without the nozzle tip guard in place. 4. Only use a nozzle tip specified by the manufacturer.5. Use caution when cleaning and changing nozzle tips. In the case where the nozzle tip clogs while spraying, ALWAYS lock gun trigger, shut pump off, and rel...

Page 4 - Setup; Adjusting the Trigger Tension

General Description This airless line striper is a precision power tool used to spraymany types of material for many types of applications includingparking lots, curbs, and athletic fields. Read and follow thisinstruction manual carefully for proper operating instructions,maintenance, and safety inf...

Page 5 - Preparing to Paint; Painting

6. Start the engine: a. Open the fuel valve lever. b. Move the throttle lever away from thegas tank. c. Close the engine choke lever. d. Holding the frame with one hand, pullthe starter roperapidly and firmly. Continue to hold the rope as you let itreturn. Pull and return the rope until the engine s...

Page 6 - Operating the Front Caster; Pressure Relief Procedure; Cleanup

12. Remove the return hose from the waste container and place it in its operating position above the container of paint. 13. Move the PRIME/SPRAY valve to the SPRAY position.14. Turn on the sprayer.15. Turn the pressure control knob slowly clockwise to increase pressure. 16. Unlock the gun by turnin...

Page 7 - Cleaning the Spray Tip; Maintenance; General Repair and Service Notes; Important Facts Concerning this Sprayer

7. Turn on the sprayer by moving the pump ON/OFF switch to theON position. 8. Slowly turn the pressure control knob clockwise to increase thepressure until fluid starts tocome out of the return hose. 9. Allow the solvent to circulate through the sprayer and flushthe paint out of the return hoseinto ...

Page 8 - Routine Engine Maintenance; Replacing the Pump ON/OFF Switch

Routine Engine Maintenance Daily • Check and fill the gas tank.• After the first 20 hours of operation, drain the oil and refill with clean oil. Check the engine oil level and fill asnecessary. Weekly • Remove the cover of the air filter and clean the element. Replace the element if necessary. If op...

Page 10 - Replacing the Transducer; Servicing the Clutch Assembly

Replacing the Transducer Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use Speeflo ESDwrist strap P/N 700-1037 or equivalent when working onelectronic pressure control. 1. Perform the Pressure Relief Procedure.2. Using a Phillips screwdriver, removethe fou...

Page 12 - Checking the Clutch Gap

Installing the Clutch Rotor Assembly, ClutchField and Drive Shaft Assembly 1. If the drive shaft grease seal was removed, press a new seal into the bore from which the old seal was removed. 2. From the clutch side of the gear housing, insert the drive shaft assembly into the bore, through the grease...

Page 13 - Servicing the Fluid Section; Servicing the Valves; Repacking the Fluid Section

Servicing the Fluid Section Use the following procedures to service the valves and repackthe fluid section. 1. Using a Phillips screwdriver, remove the four front cover screws. Remove the front cover. 2. Start the engine (refer to the procedures in the Operation section of this manual). Turn the pre...

Page 14 - Replacing the Filter

14 Reassemble the outlet valve assembly into the piston rod using the new outlet valve seal and outlet ball that camewith the repacking kit. Apply blue Loctite to the threads ofthe outlet valve retainer. Torque the outlet valve retainer to150 in./lbs. Never use a wrench on the piston rod itself. Thi...

Page 15 - Replacing the Potentiometer; Accessories; Liquid Shield Plus; Piston Lube; Miscellaneous

Replacing the Potentiometer Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use Speeflo ESDwrist strap P/N 700-1037 or equivalent when working onelectronic pressure control. 1. Perform the Pressure Relief Procedure.2. Pry off the pressure control knob cap to...

Page 16 - Solution; Cause; Troubleshooting; Problem

Troubleshooting 16 © Titan Tool Inc. All rights reserved. Solution 1. Turn the pressure control knob clockwise to supply power to the unit and increase thepressure setting. 2. Inspect or take to a Speeflo authorized service center. 3. Fill the gas tank. 1. Rotate the PRIME/SPRAY valve clockwise to t...

Page 18 - Consignes de sécurité; ATTENTION; AVERTISSEMENT; Français

18 © Titan Tool Inc. Tous droits réservés. Consignes de sécurité Le présent manuel comprend des renseignements devant êtrelus attentivement avant toute utilisation de l'appareil. Lorsquel'un des symboles suivants apparaît, il est recommandé d'êtreparticulièrement attentif et de tenir compte des mesu...

Page 19 - Sécurité du moteur à essence

© Titan Tool Inc. Tous droits réservés. 19 7. La pulvérisation à haute pression peut injecter des toxines dans le corps et causer de graves blessurescorporelles. Si une telle injection se produisait,consultez immédiatement un médecin. 8. Vérifiez les tuyaux et les pièces pour détecter des signes d’e...

Page 20 - Precauciones de seguridad; PRECAUCION; ADVERTENCIA; Español

20 © Titan Tool Inc. Todos los derechos reservados. Precauciones de seguridad Este manual contiene información que debe leer y comprenderantes de usar el equipo. Cuando se encuentre con uno de lossiguientes símbolos, asegúrese de observar sus indicacionesde seguridad. Este símbolo indica la existenc...

Page 21 - Seguridad con los motores de gasolina

© Titan Tool Inc. Todos los derechos reservados. 21 7. La pulverización a alta presión puede inyectar toxinas en el cuerpo y producir daños graves en el mismo. En casode que esto ocurra, visite a un médico inmediatamente. 8. Compruebe las mangueras y las piezas en busca de daños; una fuga puede inye...

Page 22 - Parts List; Main Assembly

22 © Titan Tool Inc. All rights reserved. Parts List Main Assembly 3 4 5 6 2 89 10 11 12 13 14 15 1 7 17 16 18 19 20 21 Item Part # Description Quantity 1 779-350 Cart assembly .............................................1 2 779-276 Gun holder assembly..................................1 3 862-436 H...

Page 23 - Drive Assembly

© Titan Tool Inc. All rights reserved. 23 Item Part # Description Quantity 1 704-380 ON/OFF switch ...........................................1 2 755-170 Electronic pressure control assembly .........1 3 700-139 Screw ..........................................................4 4 700-158 Potentiomete...

Page 25 - Electrical Schematic

© Titan Tool Inc. All rights reserved. 25 Fluid Section Assembly (P/N 755-173) 1 2 3 7 8 12 13 14 9 17 15 16 18 19 20 10 4 5 6 11 21 Install lower packing with large beveled edge facing up. Install upper packing with raised lip facing down. Raised Lip Large Beveled Edge Item Part # Description Quant...

Page 26 - Filter Assembly; Labels

26 © Titan Tool Inc. All rights reserved. Filter Assembly Item Part # Description Quantity 1 755-190 Filter body ...................................................1 2 730-067 Filter, 60 mesh ............................................1 3 702-251 Filter spring adapter..................................

Page 28 - Limited Warranty; Patents

28 © Titan Tool Inc. All rights reserved. Limited Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment coveredby this warranty is free from defects in material and workmanship. With the exception of any special, limi...