Titan 704-212S - Manuals

Titan 704-212S – Manual in PDF format online.

Manuals:

Manual

Manual Titan 704-212S

Summary

Page 2 - CAUTION; WARNING

Table of Contents Safety Precautions .................................................................2General Description ...............................................................4Operation ................................................................................4 Setup ..................

Page 3 - Earthing Instructions

9. Attention! Please observe the following when working inside and outside:No solvent gasses should be carried to the unit. Nosolvent gasses should form near the unit. Set up the uniton the opposite side to the object being sprayed. Whenspraying outdoors, take the wind direction into account.When wo...

Page 4 - Setup; Preparing a New Sprayer; Preparing to Paint

Specifications Liters per minute (LPM) ...................1.5 (0.40 GPM)Maximum tip sizes ...........................0.019”Maximum pressure ..........................20.6 MPa (3000 PSI)Power, 230V unit ..............................3/4 HP DC motor, 230V, 50/60 HZ, 4.5 AMP,1035W Power, 110V unit .......

Page 5 - Painting; Pressure Relief Procedure

6. Allow the sprayer to run for 15–30 seconds to flush the old solvent out through the return hose and into the metalwaste container. 7. Turn the unit off by moving the ON/OFF switch to the OFF position. 8. Move the PRIME/SPRAY valve up to the SPRAY position.9. Turn the unit on. Make sure the pressu...

Page 6 - Spraying; Spraying Technique; Practice

Spraying POSSIBLE INJECTION HAZARD. Do not spray without thetip guard in place. Never trigger the gun unless the tip isin either the spray or the unclog position. Always engagethe gun trigger lock before removing, replacing, orcleaning tip. Spraying Technique The following techniques, if followed, w...

Page 7 - Cleanup; Cleaning the Spray Tip

Cleanup Special cleanup instructions for use with flammablesolvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gallon container, thenflush solvents. • Area mu...

Page 8 - Maintenance; General Repair and Service Notes; Replacing the Motor Brushes

Maintenance Before proceeding, follow the Pressure Relief Procedureoutlined previously in this manual. Additionally, follow allother warnings to reduce the risk of an injection injury,injury from moving parts or electric shock. Alwaysunplug the sprayer before servicing! General Repair and Service No...

Page 9 - Replacing the Transducer; Replacing the PRIME/SPRAY Valve

8. Reassemble the pump by reversing the above steps. During reassembly, make sure the thrust washers is inplace. Replacing the Transducer 1. Loosen and remove the four front cover screws. Remove the front cover. 2. Stop the sprayer at the bottom of its stroke so that the piston is in its lowest posi...

Page 10 - Servicing the Fluid Section; Servicing the Valves; Repacking the Fluid Section

Servicing the Fluid Section Use the following procedures to service the valves and repackthe fluid section. Perform the following steps beforeperforming any maintenance on the fluid section. 1. Loosen and remove the four front cover screws. Remove the front cover. 2. Stop the sprayer at the bottom o...

Page 11 - Replacing the Filters; Pump Filter; Gun Filter

15. Position the pump block underneath the pump housing and push up until it rests against the pump housing. Make sure the transducer is aligned properly with the holein the pump block during reassembly. Improper alignmentmay cause damage to the transducer o-ring. 16. Thread the pump block mounting ...

Page 12 - Solution; Cause; Troubleshooting; Problem

Solution 1. Plug the unit in.2. Reset the breaker.3. Turn the pressure control knob clockwise to supply power to the unit and increase thepressure setting. 4. Inspect or take to a Titan authorized service center. 5. Allow motor to cool.6. Replace the ON/OFF switch. 1. Rotate the PRIME/SPRAY valve cl...

Page 14 - Consignes de sécurité; AVERTISSEMENT; ATTENTION; Français

14 © Titan Tool Inc. Tous droits réservés. Consignes de sécurité Ce manuel contient des informations qu'il faut lire etcomprendre avant d'utiliser l'appareil. En cas d'accès à unezone comportant l'un des symboles suivants, faire trèsattention et veiller à respecter les mises en garde. Ce symbole ave...

Page 15 - Directives de mise à la terre

© Titan Tool Inc. Tous droits réservés. 15 14. L’action sur la gâchette produit une force de recul sur la main tenant le pistolet.La force de recul du pistolet est particulièrement élevéeavec buse démontée et réglage maximum de la pompeAirless à haute pression. Pour cette raison, en cas denettoyage ...

Page 16 - Precauciones de Seguridad; ADVERTENCIA; PRECAUCION; Español

16 © Titan Tool Inc. Todos los derechos reservados. Precauciones de Seguridad Este manual contiene información que tiene que leerse yentenderse antes de utilizar el equipo. Cuando se encuentreen una área que tenga uno de los siguientes símbolos, estémuy atento y asegúrese que tiene en cuenta la segu...

Page 17 - Instrucciones de puesta a tierra

© Titan Tool Inc. Todos los derechos reservados. 17 13. Limpieza de la unidad. Nunca debe utilizarse una boquilla gruesa para pulverizarla unidad. En particular, nunca debe utilizarse unlimpiador de alta presión o limpiador a vapor de altapresión. Hay peligro de que el agua penetre en la unidady cau...

Page 18 - Parts List; Main Assembly

18 © Titan Tool Inc. All rights reserved. Parts List Main Assembly 1 2 3 5 6 7 4 8 9 10 11 5 Item Part # Description Quantity 1 704-181 Screw ..........................................................4 2 704-232 Motor cover .................................................1 3 ---------- Motor assemb...

Page 20 - Gear Box Assembly

Page 21 - Stand Assembly

© Titan Tool Inc. All rights reserved. 21 Item Part # Description Quantity 1 700-139 Screw ........................................................10 2 704-019 Front cover..................................................1 3 704-173 Crankshaft/gear assembly ..........................1 4 704-174 Thru...

Page 23 - Accessories; Airless Tip Selection; Piston Lube; Labels

© Titan Tool Inc. All rights reserved. 23 Item Part # Description Quantity 1 704-274 Fluid section, bare (excludes items 23–37) .1 2 704-090 Piston assembly (includes items 9–15) ......1 3 730-508 Retainer ......................................................1 4 700-587 Piston guide ..................

Page 24 - Warranty; United States Sales & Service; International; Patents

24 © Titan Tool Inc. All rights reserved. Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is freefrom defects in material and workmanship. With the exception of any special, limited, or extended ...