Titan 600-151 - Manuals

Titan 600-151 – Manual in PDF format online.

Manuals:

Manual

Manual Titan 600-151

Summary

Page 2 - Important Safety Information; Read all safety information before operating the; Grounding Instructions

2 © Titan Tool Inc. All rights reserved. Important Safety Information Read all safety information before operating the equipment. Save these instructions. Indicates a hazardous situation which, if not avoided, could result in death or serious injury.To reduce the risks of fire or explosion, electric...

Page 3 - Specifications

© Titan Tool Inc. All rights reserved. 3 Important Safety Information • Always unplug cord from outlet before working on equipment (electric models only). ImPORTANT: Do not lift cart handle when loading or unloading. Specifications Gallons per minute (GPM) ........................ 1.2 (4.5 LPM)Maxim...

Page 4 - Setup; Preparing to Spray

4 © Titan Tool Inc. All rights reserved. General Description This airless sprayer is a precision power tool used for spraying many types of materials including textured products from a ready-mixed or powdered formulation. Read and follow this instruction manual carefully for proper operating instruc...

Page 5 - Spraying; control Panel Indicators; Pressure Indicator

© Titan Tool Inc. All rights reserved. 5 7. Turn off the sprayer by moving the ON/OFF switch to the OFF position. NOTE: make sure that the spray gun does not have a tip or tip guard installed. 8. Move the PRIME/SPRAY valve up to the SPRAY position. 9. Turn on the sprayer. 10. Unlock the gun by turni...

Page 6 - Solid yellow; Solid Green; Pressure Relief Procedure; Function Keys

6 © Titan Tool Inc. All rights reserved. NOTE: If the pressure indicator begins blinking yellow when the pressure control knob is set at a higher pressure and the PRImE/SPRAy valve is in the SPRAy position, either the spray tip is worn or the sprayer is in need of service/repair. Solid yellow When t...

Page 8 - Paint Spraying Technique; Practice

8 © Titan Tool Inc. All rights reserved. Paint Spraying Technique POSSIBLE INJEcTION HAZARD. Do not spray without the tip guard in place. Never trigger the gun unless the tip is in either the spray or the unclog position. Always engage the gun trigger lock before removing, replacing, or cleaning tip...

Page 9 - cleanup; cleaning the Inlet Screen; maintenance; General Repair and Service Notes

© Titan Tool Inc. All rights reserved. 9 cleanup Special cleanup instructions for use with flammable solvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gallo...

Page 10 - NOTE: clean and refill the gear box cavity up to the rear

10 © Titan Tool Inc. All rights reserved. Replacing the motor Assembly 1. Perform the Pressure Relief Procedure and unplug the sprayer. 2. Loosen and remove the four motor shroud screws. Remove the motor shroud. 3. Release the tie wrap on the top of the baffle assembly and slip the baffle assembly d...

Page 11 - Replacing the Transducer; NOTE: make sure the o-ring on the transducer is in place; Replacing the prime/spray valve

© Titan Tool Inc. All rights reserved. 11 Replacing the Transducer 1. Perform the Pressure Relief Procedure and unplug the sprayer. 2. Loosen and remove the four motor shroud screws. Remove the motor shroud. 3. At the electronic control assembly, disconnect the wire coming from the transducer. 4. Pu...

Page 12 - Servicing the Fluid Section; Servicing the valves; Repacking the Fluid Section

12 © Titan Tool Inc. All rights reserved. Servicing the Fluid Section Use the following procedures to service the valves and repack the fluid section. Perform the following steps before performing any maintenance on the fluid section. 1. Loosen and remove the four front cover screws. Remove the fron...

Page 13 - Replacing the Filters; Gun Filter

© Titan Tool Inc. All rights reserved. 13 19. Insert the piston rod into the bottom of the upper housing, through the lower packing, through the upper packing, and out through the upper seal retainer. NOTE: When repacking the fluid section, make sure the raised lip on the bottom of the lower packing...

Page 14 - Troubleshooting

14 © Titan Tool Inc. All rights reserved. Problem A. The unit will not run. B. The unit will not prime. C. The unit will not build or maintain pressure. D. Fluid leakage at the upper end of the fluid section. E. Excessive surge at the spray gun. F. Poor spray pattern. G. The unit lacks power. cause ...

Page 15 - Xact Digital control System Error messages; Before proceeding, follow the Pressure Relief

© Titan Tool Inc. All rights reserved. 15 Xact Digital control System Error messages The following error message screens appear whenever the Xact Digital Control System detects a problem with the sprayer. Once a problem occurs and the error message appears, the sprayer will shut down. Before proceed...

Page 16 - Français; Consignes de sécurite important; Lire toutes ces consignes avant d’utiliser l’appareil.; Instructions de mise à la terre

Français 16 © Titan Tool Inc. Tous droits réservés. Consignes de sécurite important Lire toutes ces consignes avant d’utiliser l’appareil. Garder ces consignes. Indique une situation à risque, laquelle, si elle n’est pas évitée, peut entraîner des blessures graves, voire la mort.Pour réduire les ris...

Page 18 - Español; Información de seguridad importante; Lea toda la información de seguridad antes de; Instrucciones para conectar a tierra

Español 18 © Titan Tool Inc. Todos los derechos reservados. Información de seguridad importante Lea toda la información de seguridad antes de operar el equipo. Guarde estas insturcciones. Indica una situación peligrosa que, de no evitarse, puede causar la muerte o lesiones graves.Para reducir los ri...

Page 20 - Parts List; main Assembly; Description

20 © Titan Tool Inc. All rights reserved. Parts List main Assembly 1 2 3 4 9 10 5 6 15 8 1213 11 14 7 1617 1920 2122 18 Item Part # Description quantity 1 800-600 High rider cart ...........................................................1 2 800-477 Bolt ................................................

Page 21 - Drive Assembly

© Titan Tool Inc. All rights reserved. 21 Drive Assembly 29 1 34 5 6 7 8 10 9 11 12 13 1516 14 2 35 36 18 17 192021 22 2425262728 23 30 31 33 32 34 37 38 Item Part # Description quantity 1 800-078 Electronic cover ........................................................1 2 800-205 Screw ...............

Page 25 - Electrical Schematic; Motor; NOTE: All electrical work should be performed by an

© Titan Tool Inc. All rights reserved. 25 Electrical Schematic Transducer Electronic Control Assembly Potentiometer Motor Plug Control Panel Board Surge Suppressor Fuse, 15A Switch Ground WHITE WHITE BLACK WHITE AC-Motor AC-Neut AC-Line AC-Motor J16 J9 J2 J1 J12 J7 WHITE BLA CK GREEN NOTE: All elect...

Page 26 - Accessories

26 © Titan Tool Inc. All rights reserved. Accessories Airless Tip Selection Tips are selected by the orifice size and fan width. The proper selection is determined by the fan width required for a specific job and by the orifice size that will supply the desired amount of fluid and accomplish proper ...

Page 28 - Warranty • Garantie • Garantía; United States Sales & Service

28 © Titan Tool Inc. All rights reserved. Warranty • Garantie • Garantía Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of an...