Titan 335-502 - Manuals

Titan 335-502 – Manual in PDF format online.

Manuals:

Manual

Manual Titan 335-502

Summary

Page 2 - Table of Contents

Congratulations on having selected the finest airless sprayer available in the world. Titan/Speeflo piston pumps are tireless workhorses - so tough they are virtually indestructible, even under the most severe service. Titan/Speeflo designs and builds equip- ment with superior quality and reliabilit...

Page 3 - WARNING LABELS

4 CAUTION: DO NOT use this equipment to spray water or acid. CAUTION: Do not lift by cart handle when loading or unloading. WARNING LABELS Your sprayer has the English language Warning Label shown on Page 5 in the location indicated below. If you require this label in French, German, or Spanish, or ...

Page 4 - DO NOT USE EQUIPMENT BEFORE READING THIS SECTION; WARNING; HIGH PRESSURE SPRAY

5 An airless spray gun requires that fluid be introduced to it at very high pressure. Fluids under high pressure, from spray or leaks, can penetrate the skin and inject substantial quan- tities of toxic fluid into the body. If not promptly and properly treated, the injury can cause tissue death or g...

Page 5 - NO USE EL EQUIPO ANTES DE LEER ESTA SECCION; ADVERTENCIA; LA ROCIADURA A PRESION ALTA

6 Una pistola rociadora sin aire requiere que se le introduzca líquido a presión muy alta. Los líquidos bajo presión alta, de la rociadura o de las fugas, pueden penetrar en la piel e inyectar en el cuerpo cantidades considerables de líquido tóxico. Si no se atiende rápida y apropiadamente, la lesió...

Page 6 - NE PAS UTILISER LE MATERIEL AVANT D’AVOIR LU CETTE SECTION; LES PULVERISATEURS A HAUTE PRESSION PEUVENT; Pression de travail maximale: 3000 psi — 207 bar

7 Le liquide introduit dans un pistolet pulvérisateur sans air doit l’être à pression extrêmement élevée. Les liquides à haute pression, en provenance du pul- vérisateur ou d’une fuite quelconque, sont capables de pénétrer la peau et d’injecter d’importantes quan- tités de liquide toxique dans l’org...

Page 7 - SET UP; FUELING

SET UP WARNING: READ, UNDERSTAND AND FOLLOW ALL WARN-INGS ON PAGES 4 - 7 BEFORE STARTING OR OPERATINGTHIS SPRAYER Required tools: Crescent Wrench 1. Connecting the Hoses: The syphon hose and the bleed line hose have factory installed 37)( tape on the male end of the hoses. Tighten the syphon hose an...

Page 8 - Gasolines containing alcohol:; STARTUP; FLUSHING; CLEANING A CLOGGED TIP

Gasolines containing alcohol: If you decide to use a gasoline containing alcohol (gasohol), be sure its octane rating is at least as high as that recommended by Honda. There are two types of "gasohol": one containing ethanol, and the other containing methanol. Do not use gasohol that con- ta...

Page 9 - MAINTENANCE; HYDRAULIC SYSTEM; GENERAL FLUID PUMP MAINTENANCE

COLOR CHANGE / CLEAN OUT CAUTION: USE ONLY COMPATIBLE SOLVENTS WHEN CLEAN- ING OUT OIL BASED ENAMELS, LACQUERS, COAL TAR, AND EPOXIES. CHECK WITH THE FLUID MANUFACTURER FOR A RECOMMENDED SOLVENT. 1. Reduce pressure by turning the Pressure Adjustment Knob and the Pressure Bleed Valve on the bleed lin...

Page 10 - IMPORTANT ELECTRIC MOTOR INFORMATION

HYDRAULIC MOTOR & FLUID PUMP SERVICE See Page 22 for maintenance and service instructions on the reci- procating hydraulic motor and Page 26 for the fluid pump. BASIC ENGINE MAINTENANCE • For detailed engine maintenance and technical specifications refer to the separate Kawasaki engine manual. •...

Page 11 - PowrTwin 3500TM Major Components

16 DC DC GAS ELECTRIC 3.5 HP 1.5 HP GAS/ 1.5 HP ITEM PART Kawasaki 50/60 Hz 115 V ELECTRIC 50/60 Hz 220 V NO. NO. DESCRIPTION 335-500 335-501 335-502 335-503 1 335-108 Motor/Pump Assembly 1 1 1 1 2 - Hydraulic System 1 1 1 1 3 - Cart Assembly 1 1 1 1 4 506-103 Convertokit, 3.7 HP, Kawasaki, Gas 1 1 ...

Page 13 - Electric Convertokits - Service Instructions

19 Note: Brushes should be replaced when they are worn to less than 1/2 inch. Check and replace both brushes at the same time. Brush Repair Kit, Part No. 978-050, consists of: 2 brushes, 2 springs, and 2 clips. 1. Remove both inspection covers on Motor. See Figure 1. 2. Push in the Spring Clip to un...

Page 14 - Cart Assembly

20 PowrTwin 3500™ Cart Assembly CART ASSEMBLY ITEM PART NO. NO. DESCRIPTION QUANTITY 1 590-502 Handle 1 2 590-508 Roll Pin 2 3 590-507 Snap Button 2 4 856-002 Washer 4 5 856-921 Screw 4 6 590-504 Sleeve 2 7 590-506 Washer 2 8 862-002 Washer, Lock 2 9 862-428 Screw 2 10 335-561 Wheel 2 11 870-003 Was...

Page 15 - Hydraulic Motor

23 REASSEMBLY OF HYDRAULIC MOTOR 1. Replace O-Rings (6) onto Sleeve (5) after lubricating these parts with oil. CAUTION: Do not use Piston Lube pump packing lubricant. It is a solvent and will severely damage seals and O-Rings of the hydraulic motor. Gently push the Spool Sleeve Set (5) into Cylinde...

Page 16 - Pump Service Instructions

25 PowrTwin 3500™ Fluid Pump Service Instructions IMPORTANT: USE OF NON-SPEEFLO MANUFAC- TURED SERVICE PARTS MAY VOID WARRANTY.ASK FOR ORIGINAL PARTS MADE BY SPEEFLOFOR BEST SERVICES. The 143 Series Pump should receive a routine servicing after approximately 1,000 hours of use. Earlier servicing is ...

Page 19 - Gun Manifold

30 PowrTwin 3500™ Outlet Accessories (Optional) 2 Gun Manifold 2 GUN MANIFOLD PART NO. 970-110 ITEM PART NO. NO. DESCRIPTION QTY. 1 970-098 Manifold 1 2 227-027 Plug, Pipe 1 3 814-004 Nipple, Hex 1