Titan 335-500 - Manuals

Titan 335-500 – Manual in PDF format online.

Manuals:

Manual

Manual Titan 335-500

Summary

Page 2 - Table of Contents

Congratulations on having selected the finest airless sprayer available in the world. Titan/Speeflo piston pumps are tirelessworkhorses - so tough they are virtually indestructible, even underthe most severe service. Titan/Speeflo designs and builds equip-ment with superior quality and reliability. ...

Page 3 - WARNING LABELS

4 CAUTION: DO NOT use this equipment to spray water or acid. CAUTION: Do not lift by cart handle when loading or unloading. WARNING LABELS Your sprayer has the English language Warning Label shown on Page 5 in the location indicated below. If you require this label in French, German,or Spanish, or r...

Page 4 - DO NOT USE EQUIPMENT BEFORE READING THIS SECTION; WARNING; HIGH PRESSURE SPRAY

5 An airless spray gun requires that fluid be introduced to it at very high pressure. Fluidsunder high pressure, from spray or leaks, canpenetrate the skin and inject substantial quan-tities of toxic fluid into the body. If notpromptly and properly treated, the injury cancause tissue death or gangre...

Page 5 - NO USE EL EQUIPO ANTES DE LEER ESTA SECCION; ADVERTENCIA; LA ROCIADURA A PRESION ALTA

6 Una pistola rociadora sin aire requiere que se le introduzca líquido a presión muy alta. Los líquidosbajo presión alta, de la rociadura o de las fugas,pueden penetrar en la piel e inyectar en el cuerpocantidades considerables de líquido tóxico. Si no seatiende rápida y apropiadamente, la lesión pu...

Page 6 - NE PAS UTILISER LE MATERIEL AVANT D’AVOIR LU CETTE SECTION; LES PULVERISATEURS A HAUTE PRESSION PEUVENT; Pression de travail maximale: 3000 psi — 207 bar

7 Le liquide introduit dans un pistolet pulvérisateur sans air doit l’être à pression extrêmement élevée.Les liquides à haute pression, en provenance du pul-vérisateur ou d’une fuite quelconque, sont capablesde pénétrer la peau et d’injecter d’importantes quan-tités de liquide toxique dans l’organis...

Page 7 - SET UP; FUELING

SET UP WARNING: READ, UNDERSTAND AND FOLLOW ALL WARN-INGS ON PAGES 4 - 7 BEFORE STARTING OR OPERATINGTHIS SPRAYER Required tools: Crescent Wrench 1. Connecting the Hoses:The syphon hose and the bleed line hose have factory installed PTFE tape on the male end of the hoses. Tighten the syphon hose and...

Page 8 - Gasolines containing alcohol:; STARTUP; FLUSHING; CLEANING A CLOGGED TIP

Gasolines containing alcohol: If you decide to use a gasoline containing alcohol (gasohol), besure its octane rating is at least as high as that recommended byHonda. There are two types of "gasohol": one containing ethanol,and the other containing methanol. Do not use gasohol that con-tains ...

Page 9 - MAINTENANCE; HYDRAULIC SYSTEM; GENERAL FLUID PUMP MAINTENANCE

COLOR CHANGE / CLEAN OUT CAUTION: USE ONLY COMPATIBLE SOLVENTS WHEN CLEAN- ING OUT OIL BASED ENAMELS, LACQUERS, COAL TAR, ANDEPOXIES. CHECK WITH THE FLUID MANUFACTURER FOR ARECOMMENDED SOLVENT. 1. Reduce pressure by turning the Pressure Adjustment Knob andthe Pressure Bleed Valve on the bleed line c...

Page 10 - IMPORTANT ELECTRIC MOTOR INFORMATION

HYDRAULIC MOTOR & FLUID PUMP SERVICE See Page 22 for maintenance and service instructions on the reci-procating hydraulic motor and Page 26 for the fluid pump. BASIC ENGINE MAINTENANCE • For detailed engine maintenance and technical specifications refer to the separate Kawasaki engine manual. • ...

Page 11 - PowrTwin 3500TM Major Components

16 DC DC GAS ELECTRIC 3.5 HP 1.5 HP GAS/ 1.5 HP ITEM PART Kawasaki 50/60 Hz 115 V ELECTRIC 50/60 Hz 220 V NO. NO. DESCRIPTION 335-500 335-501 335-502 335-503 1 335-108 Motor/Pump Assembly 1 1 1 1 2 - Hydraulic System 1 1 1 1 3 - Cart Assembly 1 1 1 1 4 506-103 Convertokit, 3.7 HP, Kawasaki, Gas 1 1 ...

Page 13 - Electric Convertokits - Service Instructions

19 Note: Brushes should be replaced when they are worn to less than1/2 inch. Check and replace both brushes at the same time. BrushRepair Kit, Part No. 978-050, consists of: 2 brushes, 2 springs, and2 clips.1. Remove both inspection covers on Motor. See Figure 1. 2. Push in the Spring Clip to unhook...

Page 14 - Cart Assembly

20 PowrTwin 3500™ Cart Assembly CART ASSEMBLY ITEM PART NO. NO. DESCRIPTION QUANTITY 1 590-502 Handle 1 2 590-508 Roll Pin 2 3 590-507 Snap Button 2 4 856-002 Washer 4 5 856-921 Screw 4 6 590-504 Sleeve 2 7 590-506 Washer 2 8 862-002 Washer, Lock 2 9 862-428 Screw 2 10 335-561 Wheel 2 11 870-003 Was...

Page 15 - Hydraulic Motor

23 REASSEMBLY OF HYDRAULIC MOTOR1. Replace O-Rings (6) onto Sleeve (5) after lubricating these partswith oil. CAUTION: Do not use Piston Lube pump packing lubricant. It is a solvent and will severely damage seals and O-Rings of thehydraulic motor. Gently push the Spool Sleeve Set (5) into Cylinder H...

Page 16 - Pump Service Instructions

25 PowrTwin 3500™ Fluid Pump Service Instructions IMPORTANT: USE OF NON-SPEEFLO MANUFAC- TURED SERVICE PARTS MAY VOID WARRANTY.ASK FOR ORIGINAL PARTS MADE BY SPEEFLOFOR BEST SERVICES. The 143 Series Pump shouldreceive a routine servicing after approximately 1,000hours of use. Earlier servicing is re...

Page 19 - Gun Manifold

30 PowrTwin 3500™ Outlet Accessories (Optional) 2 Gun Manifold 2 GUN MANIFOLD PART NO. 970-110 ITEM PART NO. NO. DESCRIPTION QTY. 1 970-098 Manifold 1 2 227-027 Plug, Pipe 1 3 814-004 Nipple, Hex 1