Titan 230V Complete - 702-104-CE - Manuals

Titan 230V Complete - 702-104-CE – Manual in PDF format online.

Manuals:

Manual

Manual Titan 230V Complete - 702-104-CE

Summary

Page 2 - Accessories; Table of Contents

PISTON SEAL LUBRICANT Specially formulated to preventmaterials from adhering to the pistonrod, which becomes abrasive to theupper seals. Piston Lube will breakdown any material that mayaccumulate in the wet cup and keep itfrom drying. 8 oz individual 700-925 1 qt individual 700-926 8 oz, case of 12 ...

Page 4 - Electric Pump Maintenance Schedule

Check MotorBrushes Every200 Hours 4 Titan Tool is in the business of designing and manufacturing spray systems and accessories that make today’s Painting Professionalbecome more efficient and profitable. We feel that if you accurately track the maintenance of your equipment on this chart it willimpr...

Page 5 - DO NOT USE EQUIPMENT BEFORE READING THIS SECTION; WARNING; HIGH PRESSURE SPRAY

An airless spray gun requires that fluid be introduced to it at very high pressure.Fluids under high pressure, from spray orleaks, can penetrate the skin and injectsubstantial quantities of toxic fluid intothe body. If not promptly and properlytreated, the injury can cause tissue deathor gangrene an...

Page 6 - NO USE EL EQUIPO ANTES DE LEER ESTA SECCION; ADVERTENCIA; LA ROCIADURA A PRESION ALTA

6 Una pistola rociadora sin aire requiere que se le introduzca líquido a presión muy alta. Loslíquidos bajo presión alta, de la rociadura o de lasfugas, pueden penetrar en la piel e inyectar en elcuerpo cantidades considerables de líquidotóxico. Si no se atiende rápida y apropiadamente,la lesión pue...

Page 7 - NE PAS UTILISER LE MATERIEL AVANT D’AVOIR LU CETTE SECTION; LES PULVERISATEURS A HAUTE PRESSION PEUVENT; Pression de travail maximale: 3200 psi — 221 bar

7 Le liquide introduit dans un pistolet pulvérisateur sans air doit l’être à pressionextrêmement élevée. Les liquides à hautepression, en provenance du pulvérisateur ou d’unefuite quelconque, sont capables de pénétrer lapeau et d’injecter d’importantes quantités deliquide toxique dans l’organisme. S...

Page 8 - FIRE OR EXPLOSION HAZARD; ELECTRIC MOTOR; FLUID SECTION—SOLVENTS; EXPLANATION OF THE HAZARD; PELIGRO DE INCENDIO O EXPLOSIÓN

FIRE OR EXPLOSION HAZARD Static electricity is created by the high velocity of fluid through the pump, hose and tip. If every part of the spray elementis not properly grounded, sparking may occur and the system may become hazardous. Sparking may also occur whenplugging in or unplugging a power suppl...

Page 9 - SECCION FLUIDO—SOLVENTES; EXPLICACION DEL RIESGO; MOTEUR ÉLECTRIQUE

9 MOTOR A GASOLINA: (Si fuera aplicable) Siempre mantenga la bomba afuera de cualquier zona de rociadura cerrada. Mantenga el área alrededor de labomba bien ventilada. Mantenga todos los solventes lejos del escape del motor. (Nunca liene el tanque decombustible cuando el motor esté funcionando o cal...

Page 10 - EXPLICATION DU RISQUE; HALOGENATED SOLVENTS

dégâts matériels. Certains produits d'entretien, revêtements, peintures et autres liquides contiennent des solvants àhydrocarbure halogéné. Les appareils pulvérisateurs de la Titan Tool Inc. comportent des pièces en aluminium et descomposants galvanisés sensibles aux solvants à hydrocarbure halogéné...

Page 12 - APPLICATION TECHNIQUES; Proper Technique

12 The following techniques, if followed, will assure professionalpainting results. Hold the gun perpendicular to the surface and always at equaldistance from the surface. Depending on the type of material,surface or desired spray pattern, the gun should be held at adistance of 12 to 14 inches (30 t...

Page 14 - TROUBLESHOOTING AIRLESS PUMP

14 Flushing Specifications 1. New Sprayer: Oil is used by the factory for testing and protection. Itis necessary to flush unit beforespraying.A. If spraying water-base paint, flushwith mineral spirits followed bywater.B. If spraying oil-base paint, flushwith mineral spirits only. 2. Changing from wa...

Page 15 - 30V Service Instructions; Figure 3B; On/Off Switch Replacement

15 For 230 Volt Units: ITEM NO PART NO DESCRIPTION QTY 46 761-725 Power Cord 1 48 770-593 On/Off Plate 1 49 765-083 Toggle Switch 1 50 765-072 Wire 3 51 700-720 230V Fuse 10 Amp 2 54 765-050 Motor Starter 1 313-098 Earth Symbol Label 1 60 765-087 Lock Nut 1 61 765-089 Fuse Block Assembly 1 (See page...

Page 16 - Low Rider Frame Assembly

16 Figure 2 Low Rider Frame Assembly ITEM NO PART NO DESCRIPTION QTY 117 702-057 Handle 1 118 730-101 Hinge Lock 2 119 702-116 Rear Cross Member 1 120 700-802 Cap Nut 2 121 700-801 1/4” Carriage Bolt 2 122 702-127 Main Frame Right 1 123 710-045 Pin Axle 2 124 710-058 Washer Axle 2 125 702-048 Wheel ...

Page 17 - Replacement Labels

17 Epic 660HPX Syphon DownTube for use withthe High RiderFrame Only Replacement Labels PART NO DESCRIPTION QTY 700-418 Front Plate 1 (Front Cover Label) 313-175 “Warning/Attention” Label in French 1 313-1205 Wraparound Label 1

Page 18 - Armature Replacement; UNITEC Motor Complete

* ITEM NO PART NO DESCRIPTION QTY 130 761-023 Screw 2 131 702-046 Rear Cover 1 133 611-405 Snap Ring 1 135 702-040 Outer Fan 1 136 702-045 Rear Motor Housing 1 137 702-047 Wave Washer 1 138 700-681 Screw 2 *139 702-242 Armature 110V 1 For 100 Volt Units:ITEM NO PART NO DESCRIPTION QTY 139 702-241 Ar...

Page 19 - Motor Housing Replacement

141 ITEM NO PART NO DESCRIPTION QTY 140 702-404 Outer Housing 1 (Excludes 141) 141 761-244 Screw 1 142 702-084 Motor Field 1 (Excludes 143, 144) 143 700-639 Screws 4 144 702-056 Mounting Stud 2 For 100 Volt Units: ITEM NO PART NO DESCRIPTION QTY 142 702-211 Motor Field 1 Assembly 100V For 230 Volt U...

Page 20 - Gear Box

Gear Box ITEM NO PART NO DESCRIPTION QTY 21 730-260 Screw 1922 702-053 Brush Plate 2 23 702-039 Brush Insulator 2 24 765-047 Brush Gasket 2 25 702-067 Brush Spring 2 26 702-066 Brush 2 27 700-784 Screw 2 28 700-771 Adjustment Knob 1 29 700-811 O-Ring 1 30 702-079 Oil Seal (#028 O-Ring) 1 31 702-300 ...

Page 21 - Gear Replacement; Replacement of Motor Starter; Motor Brush Replacement

Gear Replacement WARNING: Before proceeding, follow the Pressure Relief Procedure outlined on Page 5. Additionally,follow all other warnings to reduce the risk of aninjection injury, injury from moving parts or electricshock. Always unplug the sprayer before servicing! 1. Remove safety plate (#43). ...

Page 22 - Filter Block

22 Epic 660HPX Filter Block ITEM NO PART NO DESCRIPTION QTY 201 710-069 Plug 2 202 702-011 Maxi Filter HSG 1 203 730-083 Filter Spring 1 204 730-067 Filter Cartridge 1 205 757-105 Filter Spring 1 206 702-303 O-Ring 1 207 702-009 Filter HSG 1 210 702-251 Adapter 1 212 730-262 1/4-20 UN Screw 2 214 22...

Page 23 - Pressure Switch Replacement

Pressure Switch Replacement WARNING: Before proceeding, follow the Pressure Relief Procedure outlined on page 5. Additionally, follow allother warnings to reduce the risk of an injection injury,injury from moving parts or electric shock. Alwaysunplug the sprayer before servicing! 1. Remove cap screw...

Page 24 - Syphon Assembly

24 Fluid Section 660HPX ITEM NO PART NO DESCRIPTION QTY 300 700-735 Crank & Slide Connecting Rod Assy. 1 301 730-508 Retainer 1 302 700-587 Upper Guide 1 304 700-603 Upper Seal 1 305 730-505 Pump Housing 1 306 700-678 Head Cap Screw 2 307 700-601 Lower Seal 2 308 730-506 Piston Rod 1 309 762-111...

Page 25 - SEAT SERVICE & REPAIR

25 Pump Section Repair andService WARNING: Before proceeding, follow the Pressure Relief Procedure outlined on page 5. Additionally,follow all other warnings to reduce the risk of aninjection injury, injury from moving parts or electricshock. Always unplug the sprayer before servicing! 1. Remove Saf...

Page 26 - Equipment Job History

26 Job Name Foreman's Name Type of Coating Date Begun Site Gallons Sprayed Tips Used Date Completed Quantity Sizes Job Name Foreman's Name Type of Coating Date Begun Site Gallons Sprayed Tips Used Date Completed Quantity Sizes Job Name Foreman's Name Type of Coating Date Begun Site Gallons Sprayed T...

Page 27 - High Rider Frame Assembly; Skid Frame Assembly

27 115V DOMESTIC PUMPS 702-405 660HPX Pump Only With low rider frame 702-410 660HPX Pump Complete With low rider frame 702-420 660HPX Pump Only With high rider frame 702-425 660HPX Pump Complete With high rider frame 702-43 5 660HPX Pump Only With skid frame 115V EXPORT PUMPS 702-143-CE 660HPX Pump ...

Page 28 - TITAN WARRANTY FOR THE 660HPX

TITAN WARRANTY FOR THE 660HPX Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to theoriginal purchaser for use (“End User”), the equipment covered by thiswarranty is free from defects in material and workmanship. Titan’sobligation under this warranty is limited to replacing or repa...