Titan 12000sv - Manuals

Titan 12000sv – Manual in PDF format online.

Manuals:

Manual

Manual Titan 12000sv

Summary

Page 2 - Important Safety Information; Read all safety information before

2 © Titan Tool Inc. All rights reserved. Important Safety Information · Read all safety information before operating the equipment. SavE ThESE INSTRucTIONS. This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury. To reduce the risks of fire or ...

Page 3 - Grounding Instructions; Gasoline Engine Safety

© Titan Tool Inc. All rights reserved. 3 Important Safety Information · Read all safety information before operating the equipment. SavE ThESE INSTRucTIONS. WaRNING – To reduce the risk of injury: 1. Always wear appropriate gloves, eye protection, clothing and a respirator or mask when painting. Haz...

Page 4 - Table of contents; PowrTex 6900 SF Gas Sprayer; PowrTex 6900 SF Electric Sprayer; Fluid section wetted parts:

4 © Titan Tool Inc. All rights reserved. Table of contents Safety Precautions ................................................................... 2 Grounding Instructions ........................................................ 3 Gasoline Engine Safety ..................................................

Page 5 - Introduction

© Titan Tool Inc. All rights reserved. 5 PowrTex 12000 SF Gas Sprayer Gallons per minute (GPM) ............. 3.15 (11.9 LPM) Cycle rate per gallon...................... 38 (10.5 cycles/liter) Maximum tip sizes ......................... 1 gun = .058” 2 guns = .040” 3 guns = .034” 4 guns = .030” 5 gun...

Page 6 - Operation; Operating the Swing cart

6 © Titan Tool Inc. All rights reserved. Operation Fueling (gas engine) Gasoline is extremely flammable and is explosive under certain conditions. • ALWAYS turn the engine off before refueling. • Refuel in a well-ventilated area. • Do not smoke or allow flames or sparks in the refueling area or wher...

Page 8 - Preparing to Spray; Spraying

8 © Titan Tool Inc. All rights reserved. • turn the engine switch to the ON position, and • pull the starter rope briskly until the engine starts. b. To start the electric motor, move the ON/OFF switch to the ON position. 7. Turn the pressure control knob clockwise approximately 1/3 of the way down ...

Page 9 - Pressure Relief Procedure

© Titan Tool Inc. All rights reserved. 9 5. Open the hydraulic shut-off valve located on the hydraulic pressure hose. The handle should be in line with the hose. 6. Open the bleed valve by turning the bleed valve knob fully counterclockwise. 7. Start the engine or turn on the electric motor. Fuel Va...

Page 10 - cleanup; cleaning a clogged Tip; Maintenance

10 © Titan Tool Inc. All rights reserved. cleanup Special cleanup instructions for use with flammable solvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gall...

Page 11 - Maintaining the hydraulic System; Maintaining the Fluid Section

© Titan Tool Inc. All rights reserved. 11 Maintaining the hydraulic System IMPORTaNT: use of Titan’s coolflo™ hydraulic Fluid is mandatory in the PowrTwin hydraulic system. Do not use any other hydraulic fluid. use of any other hydraulic fluid may seriously damage the hydraulic system and will void ...

Page 12 - Replacing the Motor Brushes (electric motor); PTFE

12 © Titan Tool Inc. All rights reserved. Replacing the Motor Brushes (electric motor) Perform this procedure using Motor Brush Kit P/N 978-050. The kit consists of two brushes, two springs, and two clips. NOTE: Brushes should be replaced when they are worn to less than 1/2 inch. check and replace b...

Page 13 - Troubleshooting

airless Gun Problem A. Spitting gun B. Gun will not shut off C. Gun does not spray airless Gun Problem A. Pump delivers on upstroke only or goes up slowly and down fast (commonly called downstroke dive) B. Pump delivers on down stroke only or goes up fast and down slowly C. Pump moves up and down fa...

Page 14 - hydraulic Motor; Problem; cause

14 © Titan Tool Inc. All rights reserved. hydraulic Motor Problem A. Oil motor stalls at bottom (no unusual heat problems) B. Oil motor stalls at top (no unusual heat problems) C. Low pressure (okay on down stroke, sluggish on up.stroke — high heat) NOTE: Engine labors on upstroke, idles back at sta...

Page 15 - Spray Patterns; Solution

© Titan Tool Inc. All rights reserved. 15 Spray Patterns Problem A. Tails B. Hour glass C. Distorted D. Pattern expanding and contracting (surge) E. Round pattern cause 1. Inadequate fluid delivery 1. Inadequate fluid delivery 1. Plugged or worn nozzle tip 1. Suction leak 2. Pulsating fluid delivery...

Page 16 - Français; consignes de sécurite important; Lire toutes ces consignes avant

Français 16 © Titan Tool Inc. Tous droits réservés. consignes de sécurite important · Lire toutes ces consignes avant d’utiliser l’appareil. GaRDER cES cONSIGNES. Indique une situation à risque, laquelle, si elle n’est pas évitée, peut entraîner des blessures graves, voire la mort.Pour réduire les r...

Page 17 - Sécurité du moteur à essence

Français © Titan Tool Inc. Tous droits réservés. 17 consignes de sécurite important · Lire toutes ces consignes avant d’utiliser l’appareil. GaRDER cES cONSIGNES. pour les embouts de pulvérisation, les protecteurs de buse, les pistolets, les rallonges, les raccords et le tuyau. 10. Verrouillez toujo...

Page 18 - Español; Información de seguridad importante; Lea toda la información de

Español 18 © Titan Tool Inc. Todos los derechos reservados. Información de seguridad importante · Lea toda la información de seguridad antes de operar el equipo. GuaRDE ESTaS INSTRuccIONES. Indica una situación peligrosa que, de no evitarse, puede causar la muerte o lesiones graves. Para reducir los...

Page 19 - Seguridad con los motores de gasolina

Español © Titan Tool Inc. Todos los derechos reservados. 19 Información de seguridad importante · Lea toda la información de seguridad antes de operar el equipo. GuaRDE ESTaS INSTRuccIONES. 12. Aprenda a detener el aparato y a liberar la presión rápidamente. Familiarícese a conciencia con los contro...

Page 20 - Parts Lists and Service Instructions; Main assembly

20 © Titan Tool Inc. All rights reserved. Parts Lists and Service Instructions Main assembly 12 34 5 6 7 1011 8 9 12000 SV Motor/Pump Assembly 6900 SF Motor/Pump Assembly Item Part # Description Quantity 1 451-135 Motor/pump assembly, 6900 SF ..................1 600-173 Motor/pump assembly, 12000 SV...

Page 21 - Belt Guard assembly

© Titan Tool Inc. All rights reserved. 21 cart assembly (P/N 451-071) 1 234 6 13 5 67 9 8 10 12 11 1415 16 7 17 Item Part # Description Quantity 1 590-502 Handle ..........................................................1 2 590-507 Snap button ..................................................2 3 59...

Page 24 - hydraulic Motor cut-away; Fluid Section; PowrTex 6900 SF Fluid Section

24 © Titan Tool Inc. All rights reserved. hydraulic Motor cut-away Torque flex locknut to 10 ft./lbs. (146N/m). Use blue Loctite. Use blue Loctite on lock ring. Seal lip must face up. Use hydraulic sealant. Torque head plug to 15 ft./lbs. (219 N/m). Do not over-tighten o-ring seal. Torque trip retai...

Page 28 - Servicing the Shovel valve; Servicing the valve Rod assembly

28 © Titan Tool Inc. All rights reserved. Servicing the Shovel valve Servicing the valve Rod assembly 1. Remove the shovel valve assembly from the fluid section by following steps 1 – 5 in the “Disassembling the Fluid Section” procedure. 2. Unscrew the suction tube (46) from the inlet valve housing ...

Page 29 - hydraulic System assembly; Torque and Sealant Guide; Item Description

© Titan Tool Inc. All rights reserved. 29 hydraulic System assembly 123 4 67 89 10 11 12 14 18 19 20 21 22 26 24 30 29 26 31 23 25 27 28 15 16 17 13 5 32 33 34 35 373839 910 42 46 29 25 43 44 45 41 40 36 Item Part # Description Quantity 1 313-755 Knob decal..............................................

Page 32 - Filter Assembly Specifications

32 © Titan Tool Inc. All rights reserved. Filter assembly(Optional, P/N 451-136) Item Part # Description Quantity 1 930-937 Filter cap assembly ...................................1 2 930-020 Spring .......................................................1 3 930-006 Filter element, 50 M, w/ball (stand...

Page 33 - accessories and Service Kits; airless Tip Selection; NOTE: Do not exceed the pump’s recommended tip size.; SaE O-Ring Fitting Installation

© Titan Tool Inc. All rights reserved. 33 accessories and Service Kits These items may be purchased separately from your local Titan distributor. Part # Description 103-830 5 Gal. Siphon Hose Assembly w/Rock Catcher 1” x 4.5’ 103-808 55 Gal. Siphon Hose Assembly w/Rock Catcher 1” x 6.5’ 103-627 Rock...

Page 35 - Notes

Page 36 - United States Sales & Service; Canadian Branch; Warranty; Patents

36 © Titan Tool Inc. All rights reserved. United States Sales & Service 1770 Fernbrook Lane Minneapolis, MN 55447 www.titantool.com 200 Trowers Road, Unit 7B Woodbridge, Ontario L4L 5Z8 Phone: Fax: 1-800-526-53621-800-528-4826 Phone: Fax: 1-800-565-86651-800-856-8496 Canadian Branch 1770 Fernbro...