Taylor C722 - Manuals

1 Model C722 To the Installer 120411 Section 1 To the Installer The following are general installation instructions.For complete installation details, please see thecheckout card. Installer Safety In all areas of the world, equipment should be installed in accordance with existing local codes.Please...

2 Model C722 To the Installer This unit must be installed on a level surface to avoid the hazard of tipping. Extreme care shouldbe taken in moving this equipment for any reason.Two or more people are required to safely move thisunit. Failure to comply may result in personal injuryor equipment damage...

3 Model C722 To the Installer 120514 Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter thanordinary polychloroprene or other equivalentsynthetic elastomer-sheathed cord (Codedesignation 60245 IEC 57) installed with the propercord anchorage to relieve conduc...

4 Model C722 To the Operator Section 2 To the Operator Your freezer has been carefully engineered andmanufactured to give you dependable operation. This unit, when properly operated and cared for, willproduce a consistent quality product. Like allmechanical products, it will require cleaning andmain...

8 Model C722 Operator Parts Identification 120507 Section 4 Operator Parts Identification Model C722 Figure 1

9 Model C722 Operator Parts Identification Model C722 Exploded View Parts Identification ITEM DESCRIPTION PART NO. 1 COVER-HOPPER-14 QT BLACK 041682-BLA 2 ORIFICE 022465-100 3 O-RING-3/8 OD X .070W 016137 4 TUBE A.-FEED-SS-5/32 HOLE X29429-2 5 O-RING-.643 OD X .077W 018572 6 PANEL-REAR 080162 7 PANE...

10 Model C722 Operator Parts Identification Door and Beater Assembly Figure 2 ITEM DESCRIPTION PART NO. 1 PLUG-PRIME TWIN 059936 2 O-RING-1/2OD X .070W 024278 3 GASKET-DOOR HT 4"-DOUBLE 048926 4 KIT A.-BEATER-FRONTSHOES-BEARING X50350 4a BEARING-FRONT SHOE *SEE NOTE 4b SHOE-FRONT HELIX-FRONT *SE...

12 Model C722 Operator Parts Identification Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 LUBRICANT-TAYLOR 047518 2 TOOL-O-RING REMOVAL 048260-WHT *3 SANITIZER-STERA SHEEN SEE NOTE 4 PAIL-MIX 10 QT 013163 ITEM DESCRIPTION PART NO. 5 TOOL-MIX PUMP SHAFTREMOVAL 057167 ** KIT A.-TUNE-UP X49463-80 * ...

13 Model C722 Operator Parts Identification Brushes Figure 5 ITEM DESCRIPTION PART NO. 1 BLACK BRISTLE BRUSH 013071 2 DOUBLE END BRUSH 013072 3 WHITE BRISTLE BRUSH(1” x 2”) 013073 ITEM DESCRIPTION PART NO. 4 WHITE BRISTLE BRUSH(3” x 7”) 023316

14 Model C722 Operator Parts Identification Optional Carts Cart A.-ADA (X69400) Cart A.-Std (X69425) Figure 6 ITEM DESCRIPTION PART NO. 1 SCREW-10-32X1/2 SLTD TRUSS 037734 2 PANEL-FRONT/REAR-ADA 069402 3 CASTER-3" SWV 3/4-10 STEMW/BRAKE 030307 4 PANEL-SIDE-CART 069403 5 CASTER-3" SWV 3/4-10 ...

15 Model C722 Important: To the Operator Section 5 Important: To the Operator Model C722 Figure 7 ITEM DESCRIPTION 1 POWER SWITCH 2 LIQUID CRYSTAL DISPLAY 3 KEYPADS 4 MIX OUT INDICATORS 5 STANDBY INDICATORS 6 MIX LOW INDICATORS 7 SELECT KEY 8 SERVICE MENU KEY 9 BRUSH CLEAN COUNTER 10 ARROW KEYS 11 T...

16 Model C722 Important: To the Operator Symbol Definitions To better communicate in the International arena,symbols have replaced words on many of ouroperator switches, function, and fault indicators.Your Taylor equipment is designed with theseInternational symbols. The following chart identifies t...

18 Model C722 Important: To the Operator Operating Screen Descriptions The fluorescent display located in the center of thecontrol panel is normally blank during the dailyoperation of the machine. The display is activatedwhen the SEL symbol or the Manager's Menu isselected. The display screen will a...

19 Model C722 Important: To the Operator Manager's Menu The Manager's Menu is used to enter the operatorfunction displays. To access the Menu, touch the center of the CONE symbol on the control panel on the right side of the machine. The arrow symbols, the SEL symbol, and the CONE symbol will be lit...

20 Model C722 Important: To the Operator Menu Options Touch the ARROW symbols to move up or downthrough the Menu. Select a Menu option by touchingthe SEL symbol. Exit the Menu program by selecting EXIT FROM MENU or touch the CONE symbol . The following menu options are listed in theManager's Menu. E...

25 Model C722 Operating Procedures Section 6 Operating Procedures The Model C722 is a medium capacity soft servemachine. Mix is stored in the hoppers. The unit isequipped with a three spout door and two 2.8 quart(2.7 liter) capacity freezing cylinders. We begin our instructions at the point where we...

30 Model C722 Operating Procedures Mix Pump Assembly Step 1 Inspect the rubber pump parts. O-rings and gasketmust be in 100% good condition for the pump andentire machine to operate properly. The o-rings andgasket cannot properly serve their intended functionif nicks, cuts, or holes in the material ...

32 Model C722 Operating Procedures Step 11 Install one red o-ring on each end of the mix feedtube, and thoroughly lubricate. (See Figure 68.) Figure 68 Step 12 Lay the pump assembly, pump clip, cotter pin, mixfeed tube, and the agitator in the bottom of the mixhopper for sanitizing. Step 13 Slide th...

34 Model C722 Operating Procedures 120507 Note: If the agitator should stop turning during normal operation, with sanitized hands , remove agitator from agitator drive shaft housing and brushclean with sanitizing solution. Install the agitatorback onto the agitator drive shaft housing. Repeat these ...

35 Model C722 Operating Procedures Draining Product From TheFreezing Cylinder Step 1 With a pail beneath the door spouts, open the draw valve. Touch the WASH and PUMP symbols . IMPORTANT! DO NOT allow the pump to keeprunning when the draw valve is closed.Excessive pressure will build up causingprodu...

36 Model C722 Operating Procedures Step 6 Raise the prime plug. Step 7 When a steady stream of cleaning solution is flowingfrom the prime plug opening in the bottom of thefreezer door, open the draw valve. Draw off all thesolution. Step 8 Once the cleaning solution stops flowing from thedoor spout, ...

37 Model C722 Operating Procedures Brush Cleaning Step 1 Prepare a sink with cleaning/sanitizing solution withan active chlorine concentrate of 100 - 200 PPM.USE WARM WATER AND FOLLOW THEMANUFACTURER'S SPECIFICATIONS. Make sureall brushes provided with the freezer are availablefor brush cleaning. St...

38 Model C722 Important: Operator Checklist Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governedby federal, state, or local regulatory agencies,and must be followed accordingly. If the unithas a “Stand...

39 Model C722 Important: Operator Checklist Winter Storage If the place of business is to be closed during thewinter months, it is important to protect the freezerby following certain precautions, particularly if thebuilding is subject to freezing conditions. Disconnect the freezer from the main pow...

40 Model C722 Important: Operator Checklist Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed. a. Low on mix. The MIX OUT light is on. a. Add mix to mix hopper. Return to AUTO mode. 34 b. The power switch is in the OFF position. b. Turn power sw...

43 Model C722 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Scraper Blade X Drive Shaft Seal X Freezer Door Gasket X Front Bearing X Front Beater Shoes X Design Caps X Draw Valve O-Ring X Mix Feed Tube O-Ring X Pump O-Ring X P...

Section 10 Parts List 44 Parts List Model C722 120413 C72227F W B E - 208- 230V 60HZ 1 P H & 208- 230V 60HZ 3 P H - A /C -BRI S T O L -( R 404A) - R O H S C O M P L IANT DE S CRI P T IO N P ART NUM BE R QTY . W ARR. CL AS S RE M ARKS ACCUMULATOR- C OPPER 2" DI A 10" LG 047062 1 103 ACTUA...