Taylor C302 - Manuals

1 Model C302 To the Installer Section 1 To the Installer The following are general installation instructions.For complete installation details, please see thecheckout card. Installer Safety In all areas of the world, equipment should be installed in accordance with existing local codes.Please contac...

2 Model C302 To the Installer 110329 Air Cooled Units Air cooled units require a minimum of 3” (76 mm) ofair space on both sides, 3” (76 mm) at the rear, and12” (305 mm) on the top of the unit. Minimum airclearances must be met to assure adequate air flowfor optimum performance. Water Cooled Refrige...

3 Model C302 To the Installer 101130 Electrical Connections Each freezer requires one power supply. Check thedata label on the freezer for branch circuitovercurrent protection or fuse, circuit ampacity andelectrical specifications. Refer to the wiring diagramprovided inside of the control box, for p...

4 Model C302 To the Installer 110329 Initial Freezing Cylinder Cleaning Due to the types of products used in FCBequipment, it is imperative that the freezing cylinderand the inlet tube be thoroughly brush cleaned,rinsed, and sanitized before running any product. Prepare a cleaning solution, using 2 ...

5 Model C302 To the Operator 110329 Section 2 To the Operator The freezer you have purchased has been carefullyengineered and manufactured to give youdependable operation. The Model C302, when properly operated and caredfor, will produce a consistent quality product. Like allmechanical products, thi...

6 Model C302 Safety 110329 Section 3 Safety We, at Taylor Company, are concerned about thesafety of the operator when he or she comes incontact with the freezer and its parts. Taylor hasgone to extreme efforts to design and manufacturebuilt-in safety features to protect both you and theservice techn...

8 Model C302 Operator Parts Identification Section 4 Operator Parts Identification C302 Figure 2 ITEM DESCRIPTION PART NO. 1 PANEL-SIDE*LEFT 059721 2 PANEL-REAR 059657 3 PANEL-SIDE*RIGHT 059722 4 DISPLAY-LIGHTED 059584-27 5 PANEL-FRONT-UPPER 059577 6 PANEL-FRONT-SHELL 059576 ITEM DESCRIPTION PART NO...

9 Model C302 Operator Parts Identification 100323 Beater Door Assembly Figure 3 ITEM DESCRIPTION PART NO. 1 DOOR A.-SLUSH PRESS. X39572-BLA 1a CAP-SPOUT-DOOR-FCB-BLK 046191-BLA 1b SPRING-COMP.480X.072X3.0 039320 1c VALVE-DRAW-DOOR-PRESS. 039324 1d O-RING-9/16 OD X .103W 016369 1e SPOUT-DOOR-FCB-BLAC...

10 Model C302 Operator Parts Identification Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 PAIL-MIX 10 QT 013163 2 BRUSH-MIX PUMP BODY-3”X7” 023316 3 BRUSH-DOUBLE ENDED 013072 4 BRUSH-REAR BRG 1”DX2“L 013071 ITEM DESCRIPTION PART NO. 5 BRUSH-DRAW VALVE 1-1/2”OD 014753 6 KIT A.-TUNE UP X59121 7 LUB...

11 Model C302 Important: To the Operator Section 5 Important: To the Operator Figure 5 ITEM DESCRIPTION 1 CONTROL SWITCH-LEFT SIDE 2 CONTROL SWITCH-RIGHT SIDE 3 KEYPAD 4 LIQUID CRYSTAL DISPLAY 5 PRODUCT LIGHT Control Switches There are two control switches located at the top leftcorner of the upper ...

12 Model C302 Important: To the Operator Liquid Crystal Displays There are two Liquid Crystal Displays (LCD's)located on the upper front panel behind theilluminated display. The two LCD's displayinformation for the two freezing cylinders locateddirectly beneath them. These pairs of freezingcylinders...

13 Model C302 Important: To the Operator 060823 Operator Menu Timeout If the display is left in the operator menu or any ofthe operator menu selections, except for CurrentConditions, the display will return to the systemmode screen 60 seconds after the last keypress.The Current Conditions screen wil...

17 Model C302 Important: To the Operator Press the AUTO (- ->) key to move to the nextscreen. The next screen will indicate when the faultwas satisfied. FAULT HISTORY 2 02/25/04 14:06:19 RESTORED FROM FAULTPAGE 2 + + + - - - SEL Press the MENU (SEL) key to return to theOPERATOR MENU. Screen H is ...

18 Model C302 Important: To the Operator CO 2 Out Indicator AUTO MODE AUTO OK SYRUP OK CO2-OUT WATER-OK On the LCD, if the word “OUT” appears next to theword “CO 2 ” it indicates a lack of CO 2 being supplied to the freezer. The product light will also illuminateand a warning tone will sound. This w...

19 Model C302 Operating Procedures Section 6 Operating Procedures The Model C302 contains four 7 quart (6.6 liter)freezing cylinders. CAUTION: This unit is pressurized when in operation. The control switches must be in the OFF position until the unit is completelyassembled. No part should ever be re...

23 Model C302 Operating Procedures Step 14 Install the prime plug. Place the two o-rings on theprime plug and lightly lubricate. Figure 20 Figure 21 Step 15 Place the large o-ring into the door groove andlightly lubricate. Figure 22 Note: Every four months or less, discard the o-rings and install ne...

24 Model C302 Operating Procedures 080307 Sanitizing IMPORTANT: If a unit is sanitized, and will not be used for an extended period of time, clean watershould be used to flush all sanitizer from the lines.Remove the water from all the lines and componentsprior to storage of the unit. Upon return to ...

29 Model C302 Operating Procedures Step 15 Close the illuminated display when complete.Replace the panels and the hood, and attach withscrews. Install the front drip tray and the splashshield on the front of the freezer. Figure 41 120 Day Closing Procedure We recommend that the machine be completely...

30 Model C302 Operating Procedures 080307 Rinsing Note: The following instructions are for one pair of freezing cylinders under an LCD. After theinstructions are complete, repeat for the two freezingcylinders on the other side of the machine under theother LCD. Step 1 To place the left cylinder in t...

31 Model C302 Operating Procedures Pressing the MENU (SEL) key will give you theoption to sanitize the left cylinder. Move the cursorunder the word “YES”. Pressing the MENU (SEL)key at this time will start the flow of cleaner/sanitizerthrough the syrup system into the freezing cylinder. SANITIZE LEF...

32 Model C302 Operating Procedures 080926 Brush Cleaning Step 1 Prepare a sink or a pail with an approved cleaningsolution. USE WARM WATER AND FOLLOW THEMANUFACTURER'S SPECIFICATIONS (examples:Kay-5® or Stera-Sheen®). IMPORTANT: Follow the label directions. Too STRONG of a solution can cause parts d...

33 Model C302 Important: Operator Checklist 080926 Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES Cleaning and sanitizing schedules are governed byyour State or local regulatory agencies and must befollowed accordingly. The following check poi...

34 Model C302 Important: Operator Checklist Winter Storage If the place of business is to be closed during thewinter months, it is important to protect the freezerby following certain precautions, particularly if thebuilding is subject to freezing conditions. Disconnect the freezer from the main pow...

35 Model C302 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. Product is too stiff. a. Too much water to syrup ratio. Improper brixadjustment. a. Adjust the brix accordingly. 27 b. Consistency control needs adjustment. b. Contact a service technician....

37 Model C302 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 4 MONTHS EVERY 8 MONTHS ANNUALLY Scraper Blade X Drive Shaft Seal X Drive Shaft O-Ring X Freezer Door O-Ring X Draw Valve O-Ring X Door Spout O-Ring X Front Bearing X Prime Plug O-Ring X Black Bristl...

Section 10 Parts List 38 Parts List Model C302 090521 + Available Separately DE S CRI P T IO N P ART NUM BE R QTY . W ARR. CL AS S RE M ARKS P ART S UP DAT E ARM A .- ID LER *356* X64892 2 103 ACCUMULATOR- C OPPER 2" DI A 13" 053377 2 000 BEARI N G- FRONT- SLUSH- PRESSURE 039349 4 000 BEARI ...