Taylor C300 - Manuals

1 Model C300 To the Installer 131210 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Installer Safety In all areas of the world, equipment should b...

2 Model C300 To the Installer Water Cooled Refrigeration Units (Water Cooled Units Only) On the back of the unit, two additional 3/8” (9.5 mm) F.P.T. water connections for condenser inlet and outlet have been provided for easy hook- up. 3/8” (9.5 mm) inside diameter water lines should be connected t...

3 Model C300 To the Installer 131210 Electrical Connections In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70- 1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arisi...

4 Model C300 To the Installer 090219 Initial Freezing Cylinder Cleaning Due to the types of products used in FCB equipment, it is imperative that the freezing cylinder and the inlet tube be thoroughly brush cleaned, rinsed, and sanitized before running any product. Prepare a cleaning solution, using...

5 Model C300 To the Operator 131210 Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Model C300, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products,...

8 Model C300 Operator Parts Identification 090417 Section 4 Operator Parts Identification Figure 2 ITEM DESCRIPTION PART NO. 1 PANEL A.-SIDE-LEFT C300 X54676-SER 2 PANEL-REAR 054672 3 PANEL-SIDE-RIGHT 054671 4 DISPLAY-LIGHTED 054683-27 5 PANEL-FRONT-UPPER 054669 6 PANEL-FRONT-SHELL 054668 ITEM DESCR...

9 Model C300 Operator Parts Identification 140509 Beater Door Assembly Figure 3 ITEM DESCRIPTION PART NO. 1 DOOR A.- FREEZER- SLUSH X80599 2 CAP- SPOUT- DOOR- FCB 046191- BLA 3 SPRING- COMP.480X.072X3.0 039320 4 VALVE- DRAW- DOOR- SLUSH 039324 *5 O- RING- 9/16 OD X .103W 016369 6 SPOUT- DOOR- FCB- B...

10 Model C300 Operator Parts Identification 140804 Accessories Figure 4 ITEM DESCRIPTION PART NO. 1 PAIL-10 QT 013163 2 BRUSH A.-PACKAGE X64275 2a BRUSH-MIX PUMP BODY-3”X7” 023316 2b BRUSH-DOUBLE ENDED 013072 2c BRUSH-REAR BRG 1”DX2“L 013071 ITEM DESCRIPTION PART NO. 2d BRUSH-DRAW VALVE 1-1/2”OD 014...

11 Model C300 Important: To the Operator Section 5 Important: To the Operator Figure 5 ITEM DESCRIPTION 1 Product Light - Left Side 2 Control Switch 3 Keypad - Left Side 4 Liquid Crystal Display 5 Keypad - Right Side 6 Product Light - Right Side Control Switch The control switch is located at the to...

12 Model C300 Important: To the Operator Pressing the AUTO (- - >) keys on both sides of the unit will display this screen. AUTO MODE AUTO OK SYRUP OK CO2 - OK WATER - OK Line 1 indicates the operating mode for each freezing cylinder. Line 2 indicates the status of the syrup systems in each freez...

18 Model C300 Operating Procedures 090417 Section 6 Operating Procedures The Model C300 contains two 7 quart (6.6 liter) freezing cylinders. CAUTION: This unit is pressurized when in operation. The control switch must be in the OFF position until the unit is completely assembled. No part should ever...

19 Model C300 Operating Procedures 090417 Step 2 Lubricate the inside diameter of the drive shaft seal. Install the drive shaft seal bushing in the drive shaft seal. Figure 7 Note: The drive shaft bushing must be positioned in the center of the drive shaft seal. Step 3 Slide the seal and bushing ove...

23 Model C300 Operating Procedures 080507 Sanitizing Note: If a unit is sanitized, and will not be used for an extended period of time, clean water should be used to flush all sanitizer from the lines. Remove the water from all the lines and components prior to storage of the unit. Upon return to se...

27 Model C300 Operating Procedures Note: The position of the handle on the syrup sampling valve determines the direction of product flow. The down position opens the syrup sampling valve for collecting brix samples. The center position shuts off the product flow. The up position directs the flow of ...

28 Model C300 Operating Procedures Draining Product From the Freezing Cylinder Step 1 With a pail beneath the door spout, press the BEATER (- - - ) key. This will allow the beater to operate and CO 2 pressure will be maintained to push the product from the freezing cylinder. Open the draw valve and ...

29 Model C300 Operating Procedures 080507 Cleaning Step 1 Prepare an approved 100 PPM cleaning solution (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5 R or 2 gal. [7.6 liters] of Stera- Sheen R ) in a clean, empty pail. USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Important: Make sure...

30 Model C300 Operating Procedures 080926 Brush Cleaning Step 1 Prepare an approved 100 PPM cleaning solution (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5 R or 2 gal. [7.6 liters] of Stera- Sheen R ). USE WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. IMPORTANT: Follow the label direction...

31 Model C300 Important: Operator Checklist 080926 Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check p...

32 Model C300 Important: Operator Checklist Winter Storage If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions. Disconnect the freezer from the main ...

33 Model C300 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. Product is too stiff. a. Too much water to syrup ratio. Improper brix adjustment. a. Adjust the brix accordingly. 25 b. Consistency control needs adjustment. b. Contact a service technician...

35 Model C300 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 4 MONTHS EVERY 8 MONTHS ANNUALLY Scraper Blade X Drive Shaft Seal X Drive Shaft O- Ring X Freezer Door O- Ring X Draw Valve O- Ring X Door Spout O- Ring X Front Bearing X Prime Plug O- Ring X Black B...

36 Model C300 Limited Warranty on Equipment 131210 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment ...

38 Model C300 Limited Warranty on Parts 131210 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement co...

40 Model C300 Limited Warranty on Parts LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNE...