Taylor 8754 - Manuals

2 Models 8751/8754 To the Operator 050818 Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Company soft-serve models covered in this manual consist of the 8751 and 8754. These units, when properly ope...

4 Models 8751/8754 Operator Parts Identification Section 4 Operator Parts Identification Model 8751 ITEM DESCRIPTION PART NO. 1 COVER A.-HOPPER X38458 2 GASKET-HOPPER COVER 038375 3 LOUVER-SIDE 017471 4 PANEL·A.-FRONT X33237 5 STUD-NOSE CONE 022822 6 PANEL-UPPER SIDE 024426 7 PANEL A.-SIDE-LOWER-LOU...

6 Models 8751/8754 Operator Parts Identification Model 8751 Single Spout Door and Beater Assembly ITEM DESCRIPTION PART NO. 1 HANDLE A.-DRAW-ADJ. X55096 1a HANDLE-ADJUSTABLE 028804 1b SCREW-ADJUSTMENT 055092 1c O-RING-1/4 OD X .070W 50 015872 1d NUT-JAM 029639-BLK 2 NUT-STUD 021508 3 DOOR A.-1 SPOUT...

7 Models 8751/8754 Operator Parts Identification Model 8754 Three Spout Door and Beater Assembly ITEM DESCRIPTION PART NO. 1 HANDLE A.- DRAW X55096 1a DRAW HANDLE 028804 1b SCREW-ADJUST 055092 1c O-RING 1/4OD X .070W 015872 1d NUT-JAM 029639-BLK 2 NUT-STUD FLAT LONG 034382 3 NUT-STUD FLAT SHORT 0343...

9 Models 8751/8754 Operator Parts Identification Accessories ITEM DESCRIPTION PART NO. 1 BRUSH-- MIX PUMP BODY 023316 2 BRUSH-- DOUBLE ENDED 013072 3 BRUSH-- REAR BEARING 013071 4 BRUSH-- DRAW VALVE 013073 5 LUBRICANT-- TAYLOR 4 OZ. 047518 ITEM DESCRIPTION PART NO. 6 SANITIZER-- KAY 5 (125 PKTS) 041...

10 Models 8751/8754 Important: To the Operator Section 5 Important: To the Operator 8751 8754 ITEM DESCRIPTION 1 MIX LOW INDICATOR LIGHT 2 MIX REFRIGERATION KEY 3 STANDBY KEY 4 WASH KEY 5 AUTO KEY ITEM DESCRIPTION 6 PUMP KEY 7 POWER ON/OFF (TOGGLE) 8 RESET BUTTON -- BEATER MOTOR 9 RESET BUTTON -- PU...

11 Models 8751/8754 Important: To the Operator Symbol Definitions To better communicate in the International arena, symbols have replaced words on many of our operator switches, function, and fault indicators. Your Taylor equipment is designed with these International symbols. The following chart id...

14 Models 8751/8754 Operating Procedures 050201 Section 6 Operating Procedures The Model 8751 has been selected to illustrate the step-by-step operating procedures for both models contained in this manual. These models, for all practical purposes of operation, are the same. Each unit stores mix in a...

18 Models 8751/8754 Operating Procedures Air/Mix Pump Assembly The purpose of the air/mix pump is to meter a specific amount of air and mix, and to transfer this combination to the freezing cylinder. Refer to the illustration on page 8 for identification of parts during assembly. Step 1 Assemble the...

21 Models 8751/8754 Operating Procedures Install the hex end of the drive shaft into the drive hub at the rear wall of the mix hopper. Figure 31 Note: For ease in installing the pump, position the ball crank of the drive shaft in the 3 o’clock position. Step 9 Lay the pump assembly, pump clip, mix f...

23 Models 8751/8754 Operating Procedures 050201 Step 9 When a steady stream of sanitizing solution is flowing from the prime plug opening in the bottom of the freezer door, pull the draw handle down. Draw off all of the sanitizing solution. ( Note: On the Model 8754, momentarily pull the center draw...

24 Models 8751/8754 Operating Procedures Step 2 Once a steady stream of mix starts to flow from the prime plug opening in the bottom of the freezer door, push down the prime plug. Figure 41 Step 3 When the mix stops bubbling down into the freezing cylinder, insert the mix feed tube. Remove the locki...

25 Models 8751/8754 Operating Procedures Draining Product From the Freezing Cylinder Step 1 Press the AUTO key, cancelling compressor and beater motor operation. Press the MIX REF key, cancelling the mix hopper refrigeration system. Step 2 Remove the hopper cover and gasket. Take these parts to the ...

26 Models 8751/8754 Operating Procedures Step 7 Once the cleaning solution stops flowing from the door spout, raise the draw handle and press the WASH key, cancelling the WASH mode. Repeat steps 1 through 7 for the other side of the freezer on the Model 8754. Disassembly Step 1 Be sure the power swi...

27 Models 8751/8754 Important: Operator Checklist 051215 Section 7 Important: Operator Checklist During Cleaning and Sanitizing Cleaning and sanitizing schedules are governed by your State or local regulatory agencies and must be followed accordingly. The following check points should be stressed du...

29 Models 8751/8754 Troubleshooting Guide Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed with draw valve open and the machine in the AUTO mode. a. Freeze-up in mix inlet hole. a. Call service technician to adjust the mix hopper temperature. -...

33 Models 8751/8754 Parts Replacement Schedule Section 9 Parts Replacement Schedule PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY Drive Shaft Seal X Scraper Blade X Freezer Door Gasket X Front Bearing X Beater Shoes X Draw Valve O-Ring X Pivot Pin O-Ring X Prime Plug O-Ring X Air Tube O-Ri...

Section 10 Parts List + Available Separately 34 Parts List Models 8751/8754 H P 62 R e fr ig er an t: 8751 - J6080596, 8754 - J 6080465/U p DE S CRI P T IO N PART NUM BE R 8751 QTY . 8754 QTY . W ARR. CL AS S RE M ARKS PART S UP DA T E AD APT O R A. --C ASTER X 18915 4 4 103 BEAR IN G --F R O N T 05...

43 + Available Separately Models 8751/8754 Parts List DE S CRI P T IO N PART S UP DA T E RE M ARKS W ARR. CL AS S 8754 QTY . 8751 QTY . PART NUM BE R OPT IONAL F E A T URES W A TER C OOLED BL O W ER 012796 -- 1 1 103 +G UA RD --B LOW E R 022505 1 1 103 CONDE NS E R 048287 1 2 103 P A N E L A .-- LO ...