Taylor 632 - Manuals

1 Model 632 To the Installer 131206 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. Installer Safety In all areas of the world, equipment should be...

3 Model 632 To the Installer 130924 S Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation. S...

4 To the Operator Model 632 131206 Section 2 To the Operator The freezer you have purchased has been carefully engineered and manufactured to give you dependable operation. The Taylor Model 632, when properly operated and cared for, will produce a consistent quality product. Like all mechanical prod...

7 Model 632 Operator Parts Identification 111101 Section 4 Operator Parts Identification Model 632 Exploded View

8 Operator Parts Identification Model 632 111101 Model 632 Parts Identification List ITEM DESCRIPTION PART NO. 1 COVER-HOPPER 053809 2 TUBE-FEED-SHAKE-5/16 HOLE 028967-7 3 TUBE A.-FEED-SS-5/32 HOLE X29429-2 4 ORIFICE 022465-100 5 O-RING-3/8 OD X .070 WIDE 016137 6 O-RING-.643 OD X .077 WIDE 018572 7...

9 Model 632 Operator Parts Identification Soft Serve Door Assembly Exploded View Item Description Part No. 1 Seal- Drive Shaft 032560 2 Shaft- Beater 032564 3 Beater A.- 3.4 Qt. 1 Pin X31761 4 O- Ring- 3/8 OD x .070 W 016137 5 Blade- Scraper- Plastic 035174 6 Bearing- Front 050216 7 Gasket- Door HT ...

10 Operator Parts Identification Model 632 Shake Door Assembly Exploded View Item Description Part No. 1 Seal- Drive Shaft 032560 2 Shaft- Beater 032790 3 Beater A.- 7 Qt.- 1 Pin X46233 4 Clip- Scraper Blade - 8.75” 046238 5 Blade- Scraper- Plastic 046237 6 Bearing- Front 013116 Item Description Par...

11 Model 632 Operator Parts Identification 140811 Accessories Item Description Part No. 1 Brush- Rear Bearing 013071 2 Brush- Double Ended 013072 3 Brush- Draw Valve 014753 4 Brush- Mix Hopper 023316 5 Lubricant- Taylor 4 oz. 047518 6 Pail- 10 qt. 013163 7 Sanitizer - Kay 5 (125 Packets) 041082

12 Important: To the Operator Model 632 Section 5 Important: To the Operator Item Description 1 Power Switch 2 Mix Low Indicator Light 3 Mix (Hopper Refrigeration) 4 Standby 5 Wash 6 Auto 7 Thermistor Control 8 Adjustable Draw Handle 9 Reset Button Power Switch When placed in the ON position, the po...

14 Important: To the Operator Model 632 Air Tube (Soft Serve) The air tube serves two purposes. One end of the tube has a hole and the other end does not. Figure 1 1. After priming the machine, lubricate the o- rings on the air tube ( the end with the hole ) and place it into the mix inlet hole. Eve...

15 Model 632 Operating Procedures 081117 Section 6 Operating Procedures We begin our instructions at the point where we enter the store in the morning and find the parts disassembled and laid out to air dry from the previous night’s cleaning.These opening procedures will show you how to assemble the...

19 Model 632 Operating Procedures Step 9 Lay the air tube (with the air orifice installed) in the bottom of the mix hopper for sanitizing. Note: The air tube for the shake side does not require o- rings or an air orifice. Freezing Cylinder Assembly - Shake Side Note: When lubricating parts, use an a...

21 Model 632 Operating Procedures 081117 Rotate the draw valve bracket to the left and center it into position by raising the draw arm and placing it into the slotted groove of the draw valve bracket. Note: The draw valve bracket must be positioned with the notch to the left. Figure 27 Step 5 Lay th...

23 Model 632 Operating Procedures Priming Step 1 With a pail beneath the door spout, open the draw handle. Be sure the prime plug is still in the UP position (soft serve side only). Pour two gallons (7.6 liters) offresh mix into the mix hopper and allow it to flow into the freezing cylinder. This wi...

24 Operating Procedures Model 632 140811 Closing Procedure To disassemble your unit, the following items will be needed: S Two cleaning pails S Sanitized stainless steel rerun can with lid S Necessary brushes (provided with freezer) S Cleaner S Single service towels Draining Product From The Freezin...

26 Important: Operator Checklist Model 632 081117 Section 7 Important: Operator Checklist During Cleaning and Sanitizing ALWAYS FOLLOW LOCAL HEALTH CODES. Cleaning and sanitizing schedules are governed by federal, state, or local regulatory agencies, and must be followed accordingly. If the unit has...

27 Model 632 Important: Operator Checklist 081117 CAUTION: Always disconnect electrical power prior to cleaning the condenser. Failure to follow this instruction may result in electrocution. j 7. If your machine is equipped with an auxiliary refrigeration system, check the auxiliary condenser for ac...

28 Troubleshooting Guide Model 632 Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed with draw valve open and the machine in the AUTO mode. a. Freeze- up in mix inlet hole. a. Call service technician to adjust the mix hopper temperature. - - - b...

31 Model 632 Limited Warranty on Equipment 131206 Section 10 Limited Warranty on Equipment TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor-branded freezer equipment a...

33 Model 632 Limited Warranty on Parts 131206 Section 11 Limited Warranty on Parts TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited warranty on new Taylor genuine replacement com...

35 Model 632 Limited Warranty on Parts LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER...