Symbol PDT 7500 Serie - Manuals

3 Q u i c k R e f e r e n c e Parts of the PDT 7500 Scan Button LCD Power Key Scan LED Front View Communication LED Battery Charge LED Thumb Rest WAN Antenna (PDT 753X only) Top View Scan Window

4 P D T 7 5 0 0 S e r i e s Parts of the PDT 7500 (continued) Bottom View Serial Communications Port IrDA Port Back View Battery Latch Li-Ion Battery

5 Q u i c k R e f e r e n c e Installing New or Recharged Batteries Caution: To ensure proper terminal operation, use ONLY the Symbol Li-Ion battery in the PDT 7500. To install a new or recharged Li-Ion battery: 1. Hook the base of the new bat- tery in the top of the battery compartment, then press ...

6 P D T 7 5 0 0 S e r i e s 3. Lift the battery up and out of the battery compartment. Charging the Battery in the Terminal To charge the terminal’s battery, place the PDT 7500 in the cradle or connect the synchronization/charging cable. The terminal’s charging LED turns yellow while charging, then ...

7 Q u i c k R e f e r e n c e LED Indication For all charging methods, the terminal’s battery charging LED indicates the battery charging status as follows: Operating the PDT 7500 Powering the Terminal On/Off Note: Before the terminal can be powered on, it must be ini-tialized and the battery must b...

8 P D T 7 5 0 0 S e r i e s Controlling the Screen Contrast To lighten the screen contrast, press the blue FUNC key, then the LIGHT key. To darken the screen contrast, press the FUNC key, then the DARK Key. Resetting the PDT 7500 If your PDT 7500 Series terminal stops responding to input from button...

9 Q u i c k R e f e r e n c e To perform a hard reset: 1. Remove the battery for 20 minutes or longer. 2. Replace the battery in the terminal. 3. The calibration screen displays. Note: With a hard reset, formats preferences and other settings are restored to their original factory defaults. Calibrat...

13 Q u i c k R e f e r e n c e Using the PDT 7500 25-Key Keypad The 25-key keypad produces the numbers 0-9, function keys F1-F10 and various action keys. • The default numeric keypad produces the numbers 0-9. • Press FUNC and the corresponding numeric key to produce the function keys F1-F10. • Press...

14 P D T 7 5 0 0 S e r i e s Using the Integrated Laser Scanner To use the laser scanner: 1. Verify the system is on. The LED lights yellow if scanning is enabled and the laser is on. 2. Aim the PDT 7500 scan window at the bar code and press the scan button. Do not hold the PDT 7500 at a right angle...

15 Q u i c k R e f e r e n c e 1. Point the scanner at the bar code and press the scan button. 2. As the raster pattern spreads, keep the pattern in the same hor- izontal plane as the bar code. 3. The terminal indicates a successful scan by changing the LED from yellow to green, beeping one or more ...

16 P D T 7 5 0 0 S e r i e s The scan beam does not have to be perfectly parallel with the top and bottom of the symbol (up to a 4 o tilt will work). Using the Imager To scan a symbol: 1. Press the scan button and center the symbol in any orientation in the aiming pattern. The entire symbol must be ...

17 Q u i c k R e f e r e n c e Host Communications The PDT 7500 Series terminal can communicate with a host PC either directly through its communications port using an RS-232 serial cable or the cradle, or wirelessly via the Spectrum24 ® wireless LANs. For more information on setting up and performi...

18 P D T 7 5 0 0 S e r i e s run the application’s print function. Printer communication can also be established through an RS-232 cable connected directly to the printer. Using the Touch Screen Some PDT 7500 terminals are equipped with a Touch Screen, which has software that allows the stylus to fu...

19 Q u i c k R e f e r e n c e Scanner does not power on when the scan button is pressed. Scanner is not enabled. See your System Administrator. Scanner does not decode a bar code. Bar code is un-readable. Verify that the bar code is not defective, i.e., smudged or bro-ken. Scan window is dirty. Cle...

21 Q u i c k R e f e r e n c e Serial Communication Port Pin-Outs Ergonomic Recommendations Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are meeting with your com...

22 P D T 7 5 0 0 S e r i e s Regulatory Information Radio Frequency Interference Requirements This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation. These limits are designed to ...

23 Q u i c k R e f e r e n c e CE Marking and European Union Compliance Products intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included: Appli...

24 P D T 7 5 0 0 S e r i e s RF Devices Symbol’s RF products are designed to be compliant with the rules and regulations in the locations into which they are sold and will be labeled as required. The majority of Symbol’s RF devices are type approved and do not require the user to obtain license or a...

25 Q u i c k R e f e r e n c e Scanner Labeling AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM THIS APERTURE ÉVITER TOUTE EXPOSITION - LUMIÈRE LASER ÉMIS PAR CETTE OUVERTURE This label is located inside the battery compartment.

27 Q u i c k R e f e r e n c e DECLARATION OF CONFORMITY We, Symbol Technologies, Inc. of One Symbol Plaza, Holtsville, NY 11742-1300, USA declare under our sole responsibility that the product Spectrum24, LA3021, Type II Radio Card Spectrum24, LA302C, Type II Radio Card Spectrum24, LA302T, Type II ...

33 Q u i c k R e f e r e n c e Warranty Symbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmansh...

72-38888-03 Revision A — September 2000 Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300 Service Information Before you use the unit, it must be configured to operate in your facility’s network and run your applications.If you have a problem running your unit or using your equipm...