Symbol LS 4208 - Manuals - manualsarea.com

Page 2 - LS 4208 Quick Reference Guide; Patents

LS 4208 Quick Reference Guide © 2005 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design.Symbol does not assume any product liability arising out of, or in connection with, the application or use of any p...

Page 4 - Scanning; Beeper Sequence

LS 4208 Quick Reference Guide 2 Scanning Beeper Definitions The scanner issues different beep sequences and patterns to indicate status. The table below defines beep sequences that occur during both normal scanning and while programming the scanner. Beeper Sequence Indication Standard Use Low/medium...

Page 5 - LED Definitions; LED

3 LED Definitions In addition to beeper sequences, the scanner communicates with the user using a two-color LED display. The table below defines LED colors that display during scanning. Code 39 Buffering Hi/lo beep New Code 39 data was entered into the buffer. 3 Beeps - long high beep Code 39 buffer...

Page 6 - Troubleshooting; Problem

LS 4208 Quick Reference Guide 4 Troubleshooting Problem Possible Cause Possible Solutions Nothing happens when the trigger is pulled. No power to the scan-ner. Check the system power. Ensure the power supply is connected if the configuration re-quires a power supply. Interface/power cables are loose...

Page 7 - Programming Bar Codes; Following are some frequently used programming bar codes.; Scan; to set all parameters to their default values.; Scanning Modes; SINGLE LINE ONLY; ALWAYS RASTER

5 Programming Bar Codes Following are some frequently used programming bar codes. Note: For additional host types, refer to the LS 4208 Product Reference Guide , p/n 72E-69413-xx, available on the LS 4208 CD, or on the Symbol website: http://www.symbol.com/manuals . Set Defaults Scan SET DEFAULTS to...

Page 8 - Host Type; to select the IBM hand-held host type. Refer to the; Keyboard Wedge Host Type

LS 4208 Quick Reference Guide 6 Host Type If a Synapse cable is used (i.e., part number STIxx-xxxx), the scanner autodetects the Synapse cable and there is no need to scan bar codes to enable the Synapse host. If a USB interface is used, the scanner autodetects the USB and defaults to the HID keyboa...

Page 11 - Scan the bar code below to enable the Scanner Emulation host.; Carriage Return/Line Feed; bar code on

9 Wand Emulation Host Type Many Wand hosts require input as Code 39 data. Scan the following bar codes to enable or disable transmission of data to the Wand host as Code 39 data. Scanner Emulation Host Type Scan the bar code below to enable the Scanner Emulation host. Carriage Return/Line Feed To ap...

Page 12 - Ergonomic Recommendations; Power Supply; Radio Frequency Interference Requirements - Canada

LS 4208 Quick Reference Guide 10 Ergonomic Recommendations Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent ...

Page 13 - Statement of Compliance; Laser Devices

11 Marking and European Economic Area (EEA) Statement of Compliance Symbol Technologies, Inc., hereby declares that this device is in compliance with all the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/. Laser Devices Symb...

Page 15 - Warranty

Warranty Subject to the terms of Symbol's hardware warranty statement, the LS 4208 hand held scanner products are warranted against defects in workmanship and materials for a period of five years from the date of shipment. The Liquid Polymer scan element includes an unprecedented limited lifetime wa...

Page 16 - Service Information; For the latest version of this guide go to:

72-69411-01Revision B - May 2005 Symbol Technologies, Inc. One Symbol PlazaHoltsville, N.Y. 11742-1300 http://www.symbol.com Service Information Before you use the unit, it must be configured to operate in your facility’s network and run your applications. If you have a problem running your unit or ...