SYLVANIA SRZ3000 - Manuals

5 EN 1A23 1 Bef ore Using 13.Outdoor Antenna grounding- If an outside antenna or cable system is connected to this product, be sure theantenna or cable system is grounded so as to provide someprotection against voltage surges and built-up staticcharges. Article 810 of the National Electrical Code,AN...

6 EN 1A23 AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE This equipment has been tested and found to com-ply with the limits for a Class B digital device, pur-suant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection againstharmful interference in a residential ins...

7 EN 1A23 Before Using 1 Bef ore Using Digital broadcasting is the most advanced format of broadcasting, employing a new technology forcompression of audio and video signals which allows broadcasters to transmit digital signals using existingterrestrial systems.Due to this dramatic progress, new fea...

8 EN 1A23 Before Using • Capable of receiving digital (ATSC*), analog (NTSC*), and cable (NTSC) broadcasts • Capable of receiving High Definition TV broadcasts • Capable of receiving Dolby® digital 5.1 audio • Alternate languages for OSD are available.(English, Spanish, French) • Component video out...

9 EN 1A23 Before Using 1 Bef ore Using 1 POWER button: Turns STB on and off. 2 POWER indicator: Lights up while STB is on. NOTE: When turning the STB on, the power indicator will blink first and light up.When turning the STB off, the power indicator will blink first and go off. 3 Remote control sens...

10 EN 1A23 Before Using 1 ANT. IN Jack: Use to connect an antenna to STB. 2 DIGITAL AUDIO (COAXIAL) Jack: Use to connect a decoder or an amplifier to STB with a digital coaxial cable. NOTE: You must use this jack and a Dolby® Digital receiver for Dolby® Digital 5.1 playback. 3 AUDIO R/ L Jacks: (2 p...

1 POWER button: Turns STB on and off. 2 Number buttons: Use to input channel numbers and passwords, andto set time. 3 ENTER button: In SETUP menu, press to determine yourselection. 4 CH o / p buttons: Press to change the channels up or down. 5 Navigation buttons o / p / s / B : Press to move the hig...

You will find STB and the following accessorieswhen unpacking the carton box of STB: 1 Unsnap the battery cover from the back of the remote control. 2 Install two AA batteries making sure the polarity (+ / -) direction is correct. NOTE: When replacing batteries, make sure to replace themin pairs. 3 ...

13 EN 1A23 Before Using 1 Bef ore Using SETUP WIZARD guides you through initial setup. "Create new setup" "Keep old setup" "SETUP" "QUIT" QUIT SETUP : : SETUP WIZARD Language for screen (1/8) ( Refer to page 30 through page 35. ) Setting the clock (Manual)(5/8) ( Refe...

14 EN 1A23 Before Using Adding channels / Deleting channels ( Refer to page 52, 55, 58, 61.) ( Refer to page 64, 66.) Adjusting antenna Receiving channels (Autoscan) Selecting screen formats (Screen ratio) Selecting screen formats (Display mode) CHANNEL QUIT CHANNEL DISPLAY CLOCK DETAIL ADD/DELETE A...

15 EN 1A23 Before Using 1 Bef ore Using Setting the clock (Daylight Savings Time) Setting the clock (Time Zone) Setting the clock (Manual) Adjusting the clock automatically CLOCK QUIT CHANNEL DISPLAY CLOCK DETAIL DST ON TIME ZONE CENTRAL MANUAL AUTO OFF 2002/ 1/31( THU ) 2 50PM CLOCK QUIT CHANNEL DI...

16 EN 1A23 Before Using V-CHIP/CC password window Setting for V-CHIP/CC Setting MPAA rating Setting TV rating Setting CC options Setting a new password DETAIL QUIT CHANNEL DISPLAY CLOCK DETAIL V-CHIP / CC MENU LANGUAGE ENGLISH V-CHIP / CC QUIT CHANNEL DISPLAY CLOCK DETAIL Enter p a s swo r d . Confi...

17 EN 1A23 Connections 2 Connections In this section Connections to antenna Connections to other devices This section allows you to finish the initial setup of STB. Connections to antenna and Connections to other devices are the important procedures to receive signals appropriately and to enjoy the ...

20 EN 1A23 Connections There will be various ways of connecting STB to other devices. Make your connection according to yourchoice of devices, screen format, and sound format.You will find some sample connections in the following pages. • All jacks on STB will not need to connected. • When you chang...

21 EN 1A23 Connections 1 Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB. 2 Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) onthe TV. NOTE: If your TV is monaural (MONO) and has only one audio jack, use a stan...

22 EN 1A23 Connections 1 Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB. 2 Use a standard audio cable to connect the audio output jacks (L, R) of STB to the audio input jacks (L, R) onthe TV. 3 Use an S-video cable to connect the S-VIDEO output jack on STB to an S-vi...

24 EN 1A23 Connections 1 Use a standard antenna cable to connect the wall jack to the ANT. IN jack on STB. 2 Use a standard audio cable to connect the audio output jacks (L, R) on STB to the audio input jacks (L, R)on the stereo. 3 Connect STB and the TV with a video cable. NOTE: Refer to the pages ...

27 EN 1A23 Connections 1 Use a standard antenna cable to connect the wall jack to the ANT IN jack on STB. 2 Use a standard audio cable to connect the set of audio output jacks (L, R) on STB to the set of audio inputjacks (L, R) on the VCR. NOTE: If your VCR is monaural (MONO) and has only one audio ...

29 EN 1A23 Initial Setups (Setup Wizard) 3 Initial Setups (Setup Wizar d) 3 Initial Setups (Setup Wizard) In this section Initial setup In Initial setup , you can finish the initial settings of STB through SETUP WIZARD instantly. ST200.qxd 03.3.19 7:05 PM Page 29

SETUP WIZARD SETUP WIZARD is the very convenient menu foryou to make the initial settings of STB. When STB is turned on for the first time afterconnecting the AC power cord, SETUP WIZARD isdisplayed on the screen automatically. You cancomplete the following items for the initial Setupsthrough this m...

3 Select a desired language using o o / p p navigation buttons, then press ENTER. • The selected language will be activated. • SETUP WIZARD 2/8 will appear. 4 STB starts scanning channels. • Wait until the scanning is complete. • When the scanning is complete, “100%” will beindicated in the box, the...

7 Select the desired time zone using o o / p p / s s / B B navigation buttons, then press ENTER. • SETUP WIZARD 5/8 will appear. NOTE : Refer to “INFORMATION on Time Zone ” on page72. 8 Enter YEAR, DATE and TIME using o o / p p / s s / B B navigation buttons or number buttons. • Every time you enter...

3 Initial Setups (Setup Wizar d) 9 Press ENTER when the cursor is on SET. • Your settings will be activated. • SETUP WIZARD 6/8 will appear, then STB willstart searching channels with Automatic ClockAdjustments to keep the time correct. 10 Select the desired channel to search from the channel map us...

When not using the auto-clock setting: Select OFF on the channel map, then press ENTER. TIP: OFF is located at the top of the channel map. Keeppressing o navigation button to search. 11 Press ENTER. • SETUP WIZARD 7/8 will appear. 12 Select the desired screen ratio using o o / p p navigation buttons...

35 EN 1A23 Initial Setups (Setup Wizard) 3 Initial Setups (Setup Wizar d) 13 Select the desired display mode using o / p navigation buttons, then press ENTER. • SETUP WIZARD is completed.STB will now start receiving broadcasts. NOTE: Refer to “Selecting screen formats” on page 64 forfurther informat...

37 EN 1A23 Basic Operation 4 Basic Operation 4 Basic Operation In this section Watching TV Channel banner Choosing audio and language Picture Still On screen messages You can find the basic operation to enjoy your STB in this section.This section contains some convenient information when watching TV...

38 EN 1A23 Basic Operation STB is capable of receiving analog (NTSC format)and digital (ATSC format) broadcasts.All available channels from any of these broadcastsources can be tuned in using the CH o / p buttons and number buttons on your remote control.Each channel number consists of a main channe...

When returning to the channel you were lastwatching: • STB will tune back in the channel you were lastwatching. About sub-channel broadcasting: There may be different programs being broadcast onsub-channels through a single channel from ATSC.You can watch each sub-channel program beingbroadcast by s...

41 EN 1A23 Basic Operation 4 Basic Operation The channel banner provides you with informationon the channel you have selected. 1 Press INFO to display a channel banner. • Channel information will appear in the channelbanner. Remote: Screen: 2 Press INFO to clear. NOTE: When tuning in a channel from ...

42 EN 1A23 Basic Operation Information icons DTV: Indicates that you are tuning in a digital channel. NTSC: Indicates that you are tuning in an analog channel. HD (High Definition): Indicates that the program being broadcast has a high definition signal with screen ratio 16:9. SD (Standard Definitio...

1 Press AUDIO button. Remote: When tuning in NTSC: The sequence will repeat as shown below whenavailable. Screen: When tuning in ATSC: The sequence will repeat according to audio-mapwhen the AUDIO button is pressed. NOTE: OTHER will be indicated when alternate languagesare not English, Spanish, or F...

You can stop the picture on the screen anytime bypressing STILL o button. 1 Press STILL o o button while watching TV. • STILL will be indicated on the lower left whilethe picture is displayed. Remote: Screen: NOTE: During STILL, the programs audio will continue. 2 Press any button to quit. • The pic...

Some messages are displayed on the screen duringchannel changing or during programs. When STB cannot receive a channel signal, thewhole screen becomes gray, then NO SIGNALappears in the center.This may occur when: • the signal is too weak • the channel is not broadcasting • the antenna cable is not ...

47 EN 1A23 Advanced Operation 5 Ad v anced Operation 5 Advanced Operation In this section Electronic Program Guide (EPG) Setup menu for preference CHANNEL Adding channels Deleting channels Adjusting antenna Receiving channels DISPLAY Selecting screen formats (Screen ratio and Display mode) CLOCK Set...

2 Select the desired program using o o / p p / s s / B B navigation buttons. • The cursor will move as you press any navigationbutton. When viewing EPG for the next two hours upto the next seven days: Press B navigation button. • EPG for the next two hours will appear. NOTE: By pressing B navigation...

50 EN 1A23 Advanced Operation Information icons LOCK: Indicates that the current program is blocked according to your V-CHIP setting. CC (Closed Caption): Indicates that the program being broadcast is available with closed captioning. Day of broadcasting Channel numbers and digitalbroadcasting stati...

You can add channels in the channel map. ADD: You can add desired channels to the channel map.Once you add channels to a channel map, you will beallowed to select the channels in order using CH o / p buttons. NOTE: When you add digital and analog channels with thesame main channel number, you will n...

2 Select CHANNEL using o o / p p navigation buttons, then press ENTER. • CHANNEL menu will appear. 3 Select ADD/ DELETE using o o / p p navigation buttons, then press ENTER. • ADD/ DELETE menu will appear. 4 To add, first enter the digital channel number 26-1. TIP: You can enter simply 26 (main chan...

5 Select ADD using o o / p p navigation buttons, then press ENTER. • 26-1 will be added to the channel map. NOTE: Digital channels can be added only with mainchannel numbers. When the digital channel added toa channel-map has sub-channels, however, the sub-channels can be selected using CH o / p but...

You can add and delete channels in the channel map. DELETE : You can delete channels from the channel-map. NOTE: When you delete digital and analog channels with thesame main channel number, you will need to deleteeach channel. NOTE: Once you delete channels from a channel-map, youcannot select thos...

3 Select ADD/DELETE using o o / p p navigation buttons, then press ENTER. • ADD/ DELETE menu will appear. 4 Select DELETE using o o / p p navigation buttons, then press ENTER. • The cursor will move to the channel map. ADD/DELETE QUIT CHANNEL DISPLAY CLOCK DETAIL 13-0 ADD DELETE

5 Select the digital channel number 26 using o o / p p navigation buttons. • 26-1 will be indicated in the box at the top of thescreen. TIP: When adding a channel number previously deleted,add the channel number by the steps in the ADDmenu or renew the whole channel map with theAUTOSCAN menu. 6 Pres...

2 Press SETUP to display SETUP menu. • SETUP menu will appear. 3 Select CHANNEL using o o / p p navigation buttons, then press ENTER. • CHANNEL menu will appear. 4 Select ANTENNA using o o / p p navigation buttons, then press ENTER. • ANTENNA menu will appear, then STB startsreceiving the signal str...

5 Adjust the antenna direction to get the best reception. • A status bar stretches to the right according to thesignal strength. • The value will be indicated on the left of thestatus bar so that you can adjust the antennadirection. When adjusting other channelscontinuously: Select the desired chann...

3 Select AUTOSCAN using o o / p p navigation buttons, then press ENTER. • AUTOSCAN menu will appear. 4 Select NEXT using s s / B B navigation buttons, then press ENTER. • Scanning window will appear, then STB will startscanning for all available channels. NOTE: It will depend on the location, howeve...

To cancel AUTOSCAN during scanning: Press SETUP or ENTER to cancel. • AUTOSCAN CANCELLED will appear on thescreen. CAUTION: If AUTOSCAN is cancelled during scanning, somechannels not yet scanned may not be received.It is recommend to complete AUTOSCAN. 5 AUTOSCAN is complete. • SETUP menu will go of...

3 Select SCREEN RATIO using o o / p p navigation buttons, then press ENTER. • Screen ratio options will appear. 4 Select the desired screen ratio using o o / p p navigation buttons, then press ENTER. • The screen ratio will be set. 5 Press ENTER to exit SETUP menu. NOTE: The screen ratio should be s...

1 Press SETUP to display SETUP menu. • SETUP menu will appear. Remote: Screen: 2 Select DISPLAY using o o / p p navigation buttons, then press ENTER. • DISPLAY menu will appear. DISPLAY QUIT CHANNEL DISPLAY CLOCK DETAIL SCREEN RATIO 4:3 DISPLAY MODE LETTERBOX SETUP QUIT CHANNEL DISPLAY CLOCK DETAIL

3 Select DISPLAY MODE, using o o / p p navigation buttons , then press ENTER. • Display mode options will appear. 4 Select the desired display mode using o o / p p navigation buttons, then press ENTER. • The display mode will be set. NOTE: You can choose the display mode as you prefer.Refer to “INFO...

5 Press SETUP to exit SETUP menu. CAUTION: If the TV is left in LETTERBOX or SIDEBAR for along period of time, the still image may cause a burn-in effect damaging the TV screen. appear because of TV settings. appear because of STB settings. STB 4:3 TV 1080i videooutput signal When your 4:3 TV (capab...

69 EN 1A23 Advanced Operation 5 Ad v anced Operation INFORMATION on Screen Ratio and Display Mode Letter Box Displays the entire picture image while fitting the picture to the screen by applying gray bars to the top and bottom of the screen. No information will be lost. Zoom Expands the picture imag...

To get the EPG (Electronic Program Guide) andChannel banner, you need to set the CLOCKcorrectly. NOTE: The clock function is featured for displaying EPG sothere may be 5 minuite-time lag a day at themaximum. Therefore we recommend to set the Autoclock setting to ON to use the clock functioneffective...

3 Select Daylight Savings Time (DST) using o o / p p navigation buttons, then press ENTER. • Daylight savings time setting menu will appear. 4 Select ON or OFF using s s / B B navigation buttons, then press ENTER. • Daylight savings time will be set, then CLOCKmenu will appear. 5 Select TIME ZONE us...

73 EN 1A23 Advanced Operation 5 Ad v anced Operation 7 Select MANUAL using o o / p p navigation buttons, then press ENTER. • The current time setting menu will appear. 8 Enter YEAR, DATE, and TIME using o o / p p / s s / B B navigation buttons or number buttons. • Press ENTER to set each value, then...

9 Press ENTER when the cursor is on SET. • Your settings will be activated. 10 Press SETUP to exit SETUP menu. CLOCK QUIT CHANNEL DISPLAY CLOCK DETAIL DST ON TIME ZONE CENTRAL MANUAL AUTO OFF 2002/ 3/31( SUN ) 1 52PM Activated 74 EN 1A23 Advanced Operation ST200.qxd 03.3.19 7:06 PM Page 74

3 Select AUTO using o o / p p navigation buttons, then press ENTER. • Auto clock setting menu will appear, then STBwill start searching for channels with clock data. When not using the auto-clock setting: Select OFF from the channel-map, then press ENTER . TIP: OFF is located at the top of the chann...

You will need to change the 4-digit password toprotect your V-CHIP/CC setting. “0000” has been stored as the default password. NOTE: Once the power supply is stopped due to the powerfailure or the unplugging AC power cord for approx.5 seconds, the password will go back to the defaultpassword “0000.”...

79 EN 1A23 Advanced Operation 5 Ad v anced Operation 5 Select NEW PASSWORD using o o / p p navigation buttons, then press ENTER. • Password setting menu will appear. 6 Enter a new 4-digit password in the upper space, then enter again in thelower space to confirm. 7 V-CHIP/CC menu will appear. • Your...

1 Press SETUP to display SETUP menu. • SETUP menu will appear. Remote: Screen: 2 Select DETAIL using o o / p p navigation buttons, then press ENTER. • DETAIL menu will appear. 3 Select V-CHIP/CC using o o / p p navigation buttons, then press ENTER. • V-CHIP/CC password window will appear. V-CHIP / C...

4 Enter your 4-digit password. • “ * ” will appear for each digit. After the correct password is entered, V-CHIP/CCmenu will appear. 5 Select V-CHIP/CC using o o / p p navigation buttons, then press ENTER. • V-CHIP/CC setting menu will appear. NOTE: To set V-CHIP/CC settings, choose STB. When choosi...

The MPAA (Motion Picture Association of America)uses the standard movie ratings. 1,7 2,3,4,5,6 4 2,3,5,6 Age Label NR Not Rated by MPAA Description G General Audience PG Parental Guidance Suggested. Some material may not be suitable for children. NC-17 No one 17 and under admitted.Some material is i...

4 Enter your 4-digit password. • “ * ” will appear for each digit. After entering the correct password, V-CHIP/CCmenu will appear. 5 Select MPAA RATING using o o / p p navigation buttons, then press ENTER. • MPAA rating setting menu will appear. V-CHIP / CC QUIT CHANNEL DISPLAY CLOCK DETAIL Set MPAA...

(TV Parental Guidelines)TV rating allows parents to block out programs theydon’t want their children to see.TV rating consists of the age labels and the contentlabels. The following are the descriptions for each label: NOTE: When you block a particular rating or content label,all categories above th...

4 Enter your 4-digit password. • “ * ” will appear for each digit. After the correct password is entered, V-CHIP/CCmenu will appear. 5 Select TV RATING using o o / p p navigation buttons, then press ENTER. • TV rating setting menu will appear. V-CHIP / CC QUIT CHANNEL DISPLAY CLOCK DETAIL Set TV rat...

Closed Caption (CC) provides you with on-screentext versions of the audio content for the programbeing broadcast. In this menu, you are allowed to turn Closed Captionsignal On or Off, to set a language for the closedcaption and to choose a format for the closed caption. NOTE: OFF has been selected a...

5 Select CC SELECTION using o o / p p navigation buttons, then press ENTER. • CC options menu will appear. 6 Select the desired CC option using o o / p p navigation buttons, then press ENTER. • The selected CC option will be set. 7 Press SETUP to exit SETUP menu. OFF: Use when Closed Caption is not ...

3 Select MENU LANGUAGE using o o / p p navigation buttons, then press ENTER. • Language menu will appear. 4 Select the desired language using o o / p p navigation buttons (E.g., select French),then press ENTER. • The selected language will be set, and theselected language will be indicated on screen...

97 EN 1A23 Appendix and Warranty 6 Appendix and W arranty 6 Appendix and Warranty In this section Troubleshooting Specifications Glossary and acronyms Warranty In this section, you will finde some service information and the manufacturer’s warranty for your STB.Before calling our service center, be ...

98 EN 1A23 Appendix and Warranty Symptom Remedy • Make sure that the AC power cord is securely plugged into the power outlet.• Make sure that STB is turned on. • Make sure to point the remote control unit at the remote control sensor.• You may be too far from STB. Try moving closer.• Remove any obst...

Product STB for ATSC/NTSC Connecting Jacks ANT IN F connector (75 ohm) Video Output (component) 3-pin jack (Y, Pb, Pr) S-Video Output Mini DIN 4-pin jack (75 ohm) Video Output 1-pin jack, 1Vpp Analog Audio Output 2-pin jack (L, R)450 mVrms (100k ohm) Digital Audio Output 1-pin jack (Dolby Digital) P...

1 Botón POWER: Para encender y apagar el STB. 2 Indicador POWER: Se ilumina cuando el STB está encendido. NOTA: Cuando se enciende el STB, el indicadorPOWER primero parpadea y luego se ilumina demanera constante. Cuando se apaga el STB, el indicador POWERprimero parpadea y luego se apaga. 3 Sensor d...

103 ES 1A23 Guía para rápida consulta 7 Gu ía para rá pida consulta 4 Botones CH o / p : Presione este botón para cambiar de canal endirección de ascenso o descenso. 5 Botones de navegación o / p / s / B : Presione estos botones para mover el cursor haciaarriba, hacia abajo, hacia la izquierda o hac...

104 ES 1A23 Guía para rápida consulta Conexiones de antena Use un cable de antena estándar para conectar la toma mural a la toma ANT IN del STB.

105 ES 1A23 Guía para rápida consulta 7 Gu ía para rá pida consulta Conexión del STB a un SDTV utilizando la salida VIDEO Panel trasero del STB Cable de audio Cable de vídeo A las tomas de entrada de audio (L, R) A la toma de entrada de vídeo NOTA: El cable de audio y el cable vídeo no vienen inclui...

106 ES 1A23 Guía para rápida consulta ASISTENTE PARA LA CONFIGURACIÓN(SETUP WIZARD) El SETUP WIZARD es un práctico menú que leayuda hacer los ajustes iniciales del STB. Cuando se enciende el STB por primera vez despuésde conectar el cable de alimentación de CA, elSETUP WIZARD aparece automáticamente...

107 ES 1A23 Guía para rápida consulta 7 Gu ía para rá pida consulta 8 Introduzca el año (YEAR), fecha (DATE) y hora (TIME) utilizando los botones denavegación o o / p p / s s / B B o los botones numéricos. • Cada vez que introduzca un número, presioneENTER para mover el cursor. • Si desea retroceder...

Printed in China LIMITED 90 DAY WARRANTY If this (product) experiences any failure due to a defect in material or workmanship within 90 daysfrom the date of purchase, return it to your nearest Sears store, and it will be replaced free ofcharge.This warranty applies only if this (product) is used for...