Stamina 15-7100B - Manuals

EQUIPMENT WARNING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Magnetic Fusion 7100 Bike. Please take a moment to familiarize yourself with all of the warning & notice labels. Label is larger than actual size WARNING LABEL(95) W1 5

H A RDWA R E I D E N T I F I C AT I O N C H A RT This chart is provided to help identify the hardware used in the assembly process. Place the washers or theends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check thelength of the bolts and screws. NO...

ASSEMBLY INSTRUCTIONS 7 STEP 1 Attach the FRONT STABILIZER(102) to the FRONT FRAME(1) with BUTTON HEAD BOLTS (M8x1.25x53mm)(65), LOCK WASHERS(M8)(88), and WASHERS(M8)(91). STEP 2 Make the WHEELS(103) on the LEFT and RIGHT FOOT CAPS(104, 105) face the front. Slide the LEFT and RIGHT FOOT CAPS(104, 10...

ASSEMBLY INSTRUCTIONS 8 STEP 3 Attach the REAR STABILIZER(6) to the REAR FRAME(5) with CARRIAGE BOLTS(M8x1.25x75mm)(63), ARC WASHERS(M8)(86), LOCK WASHERS(M8)(88), and ACORN NUTS(M8x1.25)(84). STEP 4 Screw the STAND(60) all the way up into the bottom of the FRONT FRAME(1) . Connect the PULSE EXTENSI...

ASSEMBLY INSTRUCTIONS 9 A. B. (Assembled at the factory) STEP 5 Refer to illustration A. Attach the HANDRAIL(8) to the SEAT FRAME(7) with CARRIAGE BOLTS (M8x1.25x45mm)(62), ARC WASHERS(M8)(86), LOCK WASHERS(M8)(88), and ACORN NUTS(M8x1.25) (84). STEP 6 Refer to illustration B. Slide the SEAT FRAME(7...

ASSEMBLY INSTRUCTIONS 10 STEP 7 Refer to the inset drawing. Plug the PULSE COIL WIRE(42) into the SOCKET of the PULSE EXTENSION WIRE(40) located on the REAR FRAME(5). Clip the GROMMET PLUGS(43) onto both ends of the PULSE COIL WIRE(42). Connect both ends of the PULSE COIL WIRE(42) to the PULSE SENSO...

ASSEMBLY INSTRUCTIONS 11 STEP 9 NOTE: The RIGHT PEDAL(38) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(38) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(36) has L stamped on the end of the pedal shaft. The LEFT PEDAL(36) has left hand threads and is tig...

ASSEMBLY INSTRUCTIONS 12 STEP 11 Refer to the inset drawing. Run the CONNECTION WIRE(25) through the hole in the plate on the HANDLEBAR(4). Attach the HANDLEBAR(4) to the UPRIGHT(3) with BUTTON HEAD BOLT (M8x1.25x40mm)(64) and FLAT HEAD SCREWS(M6x1x12mm)(69). STEP 12 Install four AA batteries into t...

13 SET UP INSTRUCTIONS Place the Magnetic Fusion 7100 Bike in the area where it will be used. It is recommended that the Magnetic Fusion 7100 Bike be placed on an equipment mat. The Magnetic Fusion 7100 Bike is approximately 53 1/4 inches long x 24 1/2 inches wide x 51 3/4 inches tall. (These dimens...

OPERATIONAL INSTRUCTIONS SEAT ADJUSTMENT LOAD ADJUSTMENT CAUTION: 1.2. Rotate the ADJUSTMENT KNOB(51) counterclockwise until the pin releases when the knob is pulled. Pull the ADJUSTMENT KNOB(51) and slide the SEAT FRAME(7) up or down to desired position. Lock the SEAT FRAME(7) in position by insert...

COMPUTER INSTRUCTIONS 15 MAIN DISPLAY PANEL LCD MONITOR: 1. 2. This computer provides different programsdesigned to help you meet your fitnessgoals. Simply choose the program you like,set the time for the workout, and beginexercising. The computer display will showthe elapsed time, speed, distance, ...

16 COMPUTER INSTRUCTIONS PROGRAM DESCRIPTIONS (P0) MANUAL (P1) FAT BURN (P2) MAX. FAT BURN (P3) AEROBIC (P4) HILL (P5) MOUNTAIN (P6) PLATEAU MANUAL PROGRAM: P0 is a manual program allowing the user to have full manual control of the workload. Use the " " button to increase the load. Use the ...

COMPUTER INSTRUCTIONS COMPUTER OPERATION 17 STEP 1: POWER ON Pedaling or press the MODE button. STEP 2: SET THE PROGRAM Stop pedaling for four seconds. Press the SET button and the display will flash one of the following seven programs, P0, P1, P2, P3, P4, P5, or P6. Use " / " buttons to sel...

18 1.2. 3. 4. To store the Magnetic Fusion 7100 Bike, simply keep it in a clean dry place. Adjust the SEAT FRAME(7) to the lowest position. The Magnetic Fusion 7100 Bike is approximately 53 1/4 inches long x 24 1/2 inches wide x 51 3/4 inches tall. These dimensions will vary. Please measureyour Magn...

CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive forseveral years or are severely overweight, start slowly and increase your workout time gradually. Increaseyour workout intensity gradually by monitoring your heart rate while y...

WARM-UP and COOL-DOWN Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raiseyour heart rate and warm the working muscles. Activities may include bri...

WARRANTY LIMITED WARRANTY MODEL 15-7100B Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanshipunder normal use, service and proper operation for a period of 90 days on the parts and five years on theframe from the date of the original purchase from ...

PARTS LIST PART# PART NAME QTY 1 Front Frame 1 3 Upright 1 4 Handlebar 1 5 Rear Frame 1 6 Rear Stabilizer 1 7 Seat Frame 1 8 Handrail 1 9 Pulley and Axle 1 10 Bearing (6003Z) 2 11 Bearing Washer (M17) 2 12 C Ring (17mm) 2 13 V-Ribbed Belt 1 14 Idler Arm 1 15 Idler Wheel 1 16 Idler Wheel Spacer 1 17 ...

56 Foot Stand 2 57 Leveling Cap 2 58 Cap Bushing 2 59 Securing Cap 2 60 Stand 1 61 Rectangular Plug (30mm x 60mm) 4 62 Carriage Bolt (M8 x 1.25 x 45mm) 2 63 Carriage Bolt (M8 x 1.25 x 75mm) 2 64 Bolt, Button Head (M8 x 1.25 x 40mm) 3 65 Bolt, Button Head (M8 x 1.25 x 53mm) 2 66 Bolt, Button Head (M1...

IMPORTANT : Before filling out the form below make sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach and Mail or Fax the Form Below Stamina Products, Inc. P.O. Box 1071 Springfield, MO 65801-1071 IMPORTANT : We must have your phone numb...