Stamina 15-0200C - Manuals - manualsarea.com

Page 3 - CALL US FIRST; Customer Service

3 THANK YOU FOR PURCHASING THE STAMINA INTONE Folding Recumbent Bike To help you get started, we have pre-assembled most of your INTONE Folding Recumbent Bike at the factory with the exception of those few parts left unassembled for shipping purposes. Simply follow the few assembly instructions set ...

Page 4 - BEFORE YOU BEGIN; Thank you for choosing the

4 Seat Frame THE FOLLOWING TOOL IS INCLUDED FOR ASSEMBLY : Left Cover Rear Frame Front Stabilizer Right Cover Crank Endcap Left Pedal Handrail Rear Stabilizer Adjustment Knob Meter Tension Knob Seat Leveling Cap Back Support Back Cushion Moving Wheels Combination Wrench BEFORE YOU BEGIN Right Pedal ...

Page 5 - H A RDWA R E I D E N T I F I C AT I O N C H A RT; INCHES

5 Part No. and Description Qty 56 Carriage Bolt (M8 x 1.25 x 60mm) 4 57 Carriage Bolt (M8 x 1.25 x 85mm) 1 64 Bolt, Hex Head (M8 x 1.25 x 20mm) 4 65 Bolt, Hex Head (M8 x 1.25 x 40mm) 2 69 Acorn Nut (M8 x 1.25) 4 74 Arc Washer (M8) 6 75 Washer (M8) 5 60 Screw, Round Head (M5 x 0.8 x 10mm) 2 H A RDWA ...

Page 6 - ASSEMBLY INSTRUCTIONS; INTONE

STEP 1 The FRONT STABILIZER(4) has two MOVING WHEELS(48) with an "R" decal on one end. Attach the FRONT STABILIZER(4) to the MAIN FRAME(1) with the wheels facing front and the "R" decal at the right side as shown in the illustration. Secure with the CARRIAGE BOLTS(M8x1.25x60mm)(56), ...

Page 7 - BACK

ASSEMBLY INSTRUCTIONS 7 STEP 4 Attach the SEAT(43) to the SEAT FRAME(5) with HEX BOLTS(M8x1.25x20mm)(64) and WASHERS(M8) (75). Pull the ADJUSTMENT KNOB(41), then insert the SEAT FRAME(5) into the MAIN FRAME(1) and secure with the ADJUSTMENT KNOB(41). NOTE: It may be necessary to unscrew the ADJUSTME...

Page 8 - HEX

ASSEMBLY INSTRUCTIONS 8 STEP 7 NOTE: Thread the RIGHT PEDAL(40) onto the right side of the CRANK(8). Thread the LEFT PEDAL(39) onto the left side of the CRANK(8). STEP 8 Refer to the illustration. Swing the METER BRACKET(31) up to a position where it can be seen while working out. NOTE: If necessary...

Page 9 - SET UP INSTRUCTIONS

SET UP INSTRUCTIONS 9 Place the INTONE Folding Recumbent Bike in the area where it will be used. It is recommended that the INTONE Folding Recumbent Bike be placed on an equipment mat. The maximum operation dimensions of the INTONE Folding Recumbent Bike are approximately 42 1/4" long x 25 3/8&#...

Page 10 - USING THE ELECTRONIC METER; CALORIE; OPERATIONAL INSTRUCTIONS; HOW TO INSTALL AND REPLACE BATTERIES:; RESET

10 USING THE ELECTRONIC METER CALORIE: TIME: DISTANCE: POWER OFF: Automatically scans SPEED, DISTANCE, TIME, and CALORIE in sequence with a change every five seconds. Press and release the MODE button until the arrow on the display points to "SCAN". Automatic shut off after three minutes of ...

Page 12 - STORAGE

STORAGE To store the INTONE Folding Recumbent Bike simply keep it in a clean dry place. The minimum folded dimensions of INTONE Folding Recumbent Bike are approximately 21 5/8" long x 25 3/8" wide x 42 1/4" tall. Please measure your INTONE Folding Recumbent Bike if exact dimensions are n...

Page 13 - CONDITIONING GUIDELINES; Have your doctor review your training and diet programs.

CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive forseveral years or are severely overweight, start slowly and increase your workout time gradually. Increaseyour workout intensity gradually by monitoring your heart rate while y...

Page 14 - gently; pull the upper

14 WARM-UP and COOL-DOWN Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raise yourheart rate and warm the working muscles. Activities may include ...

Page 15 - THIS WARRANTY SHALL NOT; or email us at; NO ACTION FOR BREACH OF THIS; This limited warranty is not transferable.; IF ANY PART OF THE; In; SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

15 WARRANTY LIMITED WARRANTY MODEL 15-0200C Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanshipunder normal use, service and proper operation for a period of 90 days on the parts and three years on theframe from the date of the original purchase f...

Page 16 - PRODUCT PARTS DRAWING

Page 18 - Protection Pad

PARTS LIST PART# PART NAME QTY 49 Protection Pad 1 50 Leveling Cap (50mm) 2 51 Endcap (50mm) 2 52 Rectangular Plug (30mm x 60mm) 2 53 Square Plug (30mm x 30mm) 1 54 Dome Plug (25mm) 2 55 Oval Plug (20mm x 40mm) 2 56 Carriage Bolt (M8 x 1.25 x 60mm) 4 57 Carriage Bolt (M8 x 1.25 x 85mm) 1 58 Screw, R...

Page 19 - FAX/MAIL ORDERING FORM; and the part will be mailed directly to your house.; DESCRIPTION

IMPORTANT : Before filling out the form below make sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach and Mail or Fax the Form Below Stamina Products, Inc. P.O. Box 1071 Springfield, MO 65801-1071 IMPORTANT : We must have your phone numb...