Page 3 - TABLE OF CONTENTS
3 TABLE OF CONTENTS 5 IMPORTANT SAFETY INSTRUCTIONS 6 IMPORTANT OPER ATION INSTRUCTIONS 7 PRODUCT REGISTR ATION 8 XIC600 ASSEMBLY INSTRUCTIONS 15 BIKE ADJUSTMENTS 18 CONSOLE OPER ATION 20 FEATURES24 TROUBLESHOOTING25 GENER AL MAINTENANCE 26 MANUFACTURER’S LIMITED WARR ANTY Thank you for purchasing o...
Page 5 - Important Safety Instructions; WARNING
5 Important Safety Instructions WARNING Read all instructions before using this appliance. WARNING - To reduce the risk of injur y to persons, install the Indoor Bike on a flat level surface. • Use this equipment only for its intended use as described in this manual. Do not attempt to ride this bike...
Page 6 - Important Operation Instructions; overexer tion or injur y.
6 Important Operation Instructions WARNING AS THE OWNER OF THIS EXERCISE EQUIPMENT, YOU SHOULD INSIST THAT ALL USERS FOLLOW THE SAME GUIDELINES: YOU SHOULD MAKE THIS MANUAL AVAILABLE TO ALL USERS. 1. Obtain a complete physical examination from your medical doctor and enlist a health/fitness professi...
Page 7 - • NEVER; Record Your Serial Number; Register Your Purchase; under the Suppor t tab to register online.
7 Important Operation Instructions • NEVER operate this Indoor Cycle without reading and completely understanding the owner’s manual. • Use caution while par ticipating in other activities while pedaling on your Indoor Cycle; such as watching television, reading, etc. These distractions may cause yo...
Page 8 - PRE ASSEMBLY
8 XIC600 PRE ASSEMBLY UNPACKING 1. Cut the straps, then lift the box over the unit and unpack. 2. Carefully remove all par ts from the car ton and inspect for any damage or missing par ts. If par ts are damaged or missing, contact your dealer immediately. 3. Locate the hardware package. Remove the t...
Page 11 - STEP THREE
11 XIC600 STEP THREE HARDWARE FOR STEP 3 PART TYPE DESCRIPTION QTY 88 BOLT 5/16”X15mm 4 49 SPLIT WASHERS 5/16” 4 48 FLAT WASHERS 5/16” 4 1. Gather HARDWARE FOR STEP 3 . 2. Install the handlebars with four BOLTS (88) , SPLIT WASHERS (49) and four FLAT WASHERS (48) . Tighten the bolts securely. 3. Ins...
Page 12 - STEP FOUR
12 XIC600 STEP FOUR 1. Install the LEFT (25L) and Right (25R) pedals to the crank arms. Please note that the Left pedal has a reverse threaded bolt and needs to be tightened in a counterclockwise direction. The pedals are identified by either an R or L stamped into the end of the bolt. 25(R) 25(L)
Page 13 - STEP FIVE
13 XIC600 STEP FIVE Cycling Console Battery Installation: 1. Remove the batter y cover from the back of the computer. 2. Inser t 2 AAA batteries into the batter y compar tment and reinstall the batter y cover. 3. When Batter y working voltage is too low, The “Low batter y” indicator will show up on ...
Page 15 - ADJUSTING BIKE
15 XIC600 ADJUSTING BIKE Take some time to learn how to properly adjust the bike to your body; it will make your workouts more pleasant and a safer experience too. Riding the bike when it is incorrectly adjusted can result in discomfort and increase your risk of injury. Adjustment of Seat Position S...
Page 16 - DUAL FUNCTION PEDAL; ADJUSTING THE PEDAL STRAPS
16 Handlebar Adjustment Handlebar Height Adjustment 1. The Handlebar height is a matter of preference. Star t with a handlebar height that is the same as the seat’s height. Adjusting the handlebar higher will give the rider a more upright position; lower will result in a more crouched position. 2. R...
Page 17 - BASIC OPERATION
17 XIC600 BASIC OPERATION Now that you have established a proper riding position, take a few minutes to ride the bike and determine that your position is comfor table. Star t pedaling at a slow pace with your toes and knees pointed directly forward. Hold the handlebar lightly and in a position that ...
Page 18 - CONSOLE OPERA; TION
18 XIC600 CONSOLE OPERA TION Large LCD Matrix Window Easy-Touch Control Buttons Built-in Heart Rate Receiver
Page 19 - CONSOLE OPERATION
19 XIC600 CONSOLE OPERATION PLEASE NOTE: 1. The Cycling Monitor system is designed as sealed unit and not meant to be opened other than for the sole purpose of installing batteries. Any opened units will void the warranty. 2. To clean the Cycling Monitor use a clean damp cloth. Use of any caustic cl...
Page 20 - FEATURES; screen, also called “QUICK Start” active state.
20 XIC600 FEATURES TIME Time is measured in min:sec There is a time of day clock and a workout timer clock. The workout time will count up or count down during pedaling. If pedaling stops, the time will stop counting after 3sec. RPM/CADENCE Cadence is the measurement of how fast the cranks are rotat...
Page 24 - TROUBLESHOOTING; No Display on Console; Hold down any key to bring the console to “Quick Star t” mode.; No Heart Rate signal displayed; Notice of FCC Compliance
24 TROUBLESHOOTING No Display on Console Hold down any key to bring the console to “Quick Star t” mode. Ensure that the batteries are installed properly in the console and transmitter. If they are, install fresh batteries. No Heart Rate signal displayed Ensure that your chest strap (sold separately)...
Page 25 - GENERAL MAINTENANCE; Part; Ensure that pedals are tight in crank arms that all
25 GENERAL MAINTENANCE 1. Do not ser vice internal par ts of pedals. If they are found to be worn internally, we recommend replacing the pedal. 2. Use of lubricants or cleaning solutions other than those specified will result in diminished performance and a shor ter life span for that par t. 3. Wipe...
Page 26 - Indoor Cycle Warranty - Effective August 22, 2018
26 Indoor Cycle Warranty - Effective August 22, 2018 Spirit Fitness, Inc. (Spirit Fitness) warrants all its Indoor Cycle par ts for a period of time listed below from the date of retail sale, as determined by sale receipt, or in the absence of a sales receipt eighteen (18) months from the original f...
