Sonance IS10CENTER - Manuals

Page 4 - INSTALLATION ACCESSORIES

4 PRODUCT PREPARATION Amplifier Selection Sonance DSP Amplifiers are highly recommended for IS6, IS8, and IS10 full-range speakers. These amps have preloaded curves to optimize the performance of Invisible Series speakers and woofers. Preconfigured curves for various finish types and thicknesses all...

Page 8 - RETROFIT INSTALLATION; NOTE: We highly recommend you keep the

8 RETROFIT INSTALLATION 1. Remove the included cutout template that is taped to the front of each speaker. 2. Locate the studs in your install location and mark the centers of the studs/joists. Position and affix the template so that it is perfectly centered on both left and right studs. 3. Mark aro...

Page 9 - NEW CONSTRUCTION INSTALLATION; This is to avoid interfering with the Sonance

9 NEW CONSTRUCTION INSTALLATION 1. Run speaker wire from the amplifier and audio component location to desired speaker locations. See page 4 for wire gauge chart. 2. We recommend that you reinforce the top and bottom joint locations with a face-block-oriented 2x4 or 3/4” (19mm) plywood. See the cons...

Page 11 - IMPORTANT; PRE-FINISHING TESTING; Installation Fit Test

11 12. Ensure the center of the speaker diaphragm (not the recessed edges) is flush with the surrounding drywall. Adjust shims if necessary. 13. IMPORTANT : Test the speaker with an audio source at moderate listening levels to ensure it functions properly before completing the installation. Follow t...

Page 12 - FINISHING INSTRUCTIONS; Allow hot mud to set slightly before applying mesh

12 FINISHING INSTRUCTIONS NOTE: Drywall finishes can range in various levels of smoothness. For invisible speaker installations, we recommend at least a level four finish where drywall seams are all feathered out and sanded. For best results, we recommend a level five finish where the entire wall pl...

Page 14 - FINISH THICKNESS GUIDELINES; TOTAL FINISH THICKNESS FOR OPTIMAL

14 10. Apply a second coat of topping compound covering the entire surface of the speaker and all adjoining surfaces. 11. Compound buildup on the active surface of the speaker should not exceed 3mm (1/8”). 12. Detail the compound to minimize tool marks. 13. Allow each layer to fully cure. This can t...

Page 16 - TECHNICAL SPECIFICATIONS

16 IS6 Full-range Speaker IS8 Full-range Speaker IS10 Full-range Speaker IS10W Woofer Wave Flex Drive Unit 20in ² (127cm ² ) bending wave diaphragm 1.75” (44mm) voice coil 29in ² (188cm ² ) bending wave diaphragm 1.75" (44mm) voice coil 29in ² (188cm ² ) bending wave diaphragm 1.75" (44mm) v...

Page 17 - FREQUENTLY ASKED QUESTIONS

17 FREQUENTLY ASKED QUESTIONS Can Invisible Series speakers be installed in the ceiling or just in walls? Sonance IS speakers can be installed in both walls and ceilings. Where is the best place to locate the speakers? If installing into walls, make sure they are at least 7’ (2.13m) from the floor. ...

Page 18 - Are these suitable for surround sound?; correction of the AV receiver/surround processor for; What’s the benefit of Sound-Isolating enclosures?; Use stainless steel #6 drywall screws in the appropriate; Is there a protection circuit built into the speaker or; The 15 Year limited warranty covers the cost to replace

18 Are these suitable for surround sound? Motion Flex invisible speakers can be used in surround sound applications. Always use a subwoofer and an 80Hz high pass filter applied to the invisible speakers in surround sound applications. Use the built-in room- correction of the AV receiver/surround pro...

Page 19 - YOU MUST HAVE PRIOR

19 TECHNICAL ASSISTANCE AND SERVICE The Technical Assistance Department at Sonance is available at (949) 492-7777 to answer any questions concerning the operation and installation of your speakers between the hours of 7:00 AM and 5:00 PM Pacific time, Monday through Friday, except holidays. In the e...