Sonance 92746 - User Manual

I n t r o d u c t i o n

Thank you for purchasing Sonance Rock Speakers. When properly
installed, these speakers will provide you with years of outdoor
entertainment pleasure. To get the most out of your new speakers,
please read this manual thoroughly before you begin installation.

B o x C o n t e n t s

Sonance Rock Speaker boxes contain two (2) Rock Speakers.

C o n n e c t i n g t h e S p e a k e r s

1.

Determine the locations for the speakers and estimate the
length of additional wire you will need for each speaker.
(Sonance Rock Speakers feature a wide angle of coverage —
only a few speakers are needed to cover a large area with
sound.)

N

OT E

: W

H E N P U R C H A S I N G A D D I T I O N A L W I R E

, S

O N A N C E

S T R O N G LY R E C O M M E N D S U S I N G D I R E C T B U R I A L G R A D E W I R E

.

2.

Dig a 4” – 5” deep trench to run the speaker wires in.

3.

Run the wire through the trench from your amplifier to the
speaker locations. Do not connect the wires to the amplifier
at this time.

4.

Connect the speaker wires you ran from your amplifier to
the wires that came attached to the speakers (see

Figure 1

).

Sonance recommends using waterproof wire nuts
(not included) to secure the wires.

I M P O RTA N T: B

E S U R E N OT TO L E T A N Y S T R AY

‘ + ’

A N D

‘ – ’

S T R A N D S TO U C H E A C H OT H E R

. T

O U C H I N G S T R A N D S C A N C A U S E

A S H O R T

-

C I R C U I T T H AT C O U L D D A M A G E YO U R A M P L I F I E R

.

5.

After you have made the above connections, connect the
wires to your amplifier.

N

OT E

: C

O N F I R M T H AT YO U H AV E C O N N E C T E D S P E A K E R

“+”

TO

A M P L I F I E R

“+”

A N D S P E A K E R

“–”

TO A M P L I F I E R

“–”.

6

.

Turn your amplifier on and test the system with your favorite
music. If the speakers are operating properly, refill the wire
trench and enjoy your new speakers.

S p e c i f i c a t i o n s

R K 8 3

Tweeter:

1” (25mm) polyurethane dome,
ferrofluid-cooled

Woofer:

8” (203mm) polypropylene cone with
a Santoprene™ surround

Frequency Response:

40Hz – 20 kHz ±3dB

Impedance:

8 ohms nominal; 6 ohms minimum

Power Handling:

5 watts minimum; 150 watts maximum

Sensitivity:

90dB SPL (2.83V/1 meter)

Available Finishes:

Granite; brown

Dimensions (WxHxD):

14

5

/

8

” x 14¼” x 17¾”

(372mm x 362mm x 451mm)

Shipping Weight:

35 lbs (15.8kg) pair

R K 6 3

Tweeter:

1” (25mm) polyurethane dome,
ferrofluid-cooled

Woofer:

6½” (165mm) polypropylene cone
with a Santoprene™ surround

Frequency Response:

50Hz – 20 kHz ±3dB

Impedance:

8 ohms nominal; 6 ohms minimum

Power Handling:

5 watts minimum; 100 watts maximum

Sensitivity:

89dB SPL (2.83V/1 meter)

Available Finishes:

Granite; brown

Dimensions (WxHxD):

11” x 10½” x 14”
(279mm x 267mm x 356mm)

Shipping Weight:

28 lbs (12.6kg) pair

Twist

Wires

Together

Waterproof

Wire Nuts

From Speaker

To Amplifier

I N S T R U C T I O N M A N U A L

S O N A N C E

®

L A N D S C A P E S E R I E S

R K 8 3 , R K 6 3

R O C K

S P E A K E R S

F

IGURE

1: C

ONNECTING THE

R

OCK

S

PEAKERS