Siemens XPS15F - Manuals

7ML19981AK01.2 XPS/XCT Transducers 5 SPECIFICATIONS Model : XPS - 10 XPS - 15 XPS - 30 XPS - 40 XCT - 8 XCT - 12 MeasurementRange, 0.3 - 10 0.3 - 15 0.6 - 30 0.9 - 40 0.6 - 8 0.6 - 12 m (ft): (1-33) (1-50) (2-100) (3-130) (2-26) (2-40) Frequency(kHz): 43 43 30 22 43 43 Beam Angle: 12° 6° 6° 6° 12° 6...

OUTLINE AND DIMENSIONS radiating face optional submergence shield refer to associated instructions optional bonded flange refer to associated instructions standard optional split flange refer to associated instructions Model Dimension XPS - 10 XPS - 15 XPS - 30 XPS - 40 XCT - 8 XCT - 12 A 86 mm (3.4...

MOUNTING DO’S AND DON’TS Special handling precautions must be taken to protect the face of the transducer from anydamage. Mount the transducer so that it is above the maximum material level by at least the blanking value . Refer to the associated transceiver manual. On liquid applications, the trans...

MOUNTING - LIQUID APPLICATIONS Flexible Conduit Bracket Submersible Plywood rigid metal conduit coupling transducer safetychain flexibleconduit steel channel coupling safetychain submergenceshield Flexible conduit mounted transducer shouldnot be subjected to wind, vibration or jarring. Submersible t...

INTERCONNECTION For EnviroRanger ERS 500 only, connect all three wires separately. When connecting to an EnviroRanger ERS 500, do NOT use coaxial cable, use a 2-wire extension as illustrated above. For EnviroRanger ERS 500 only, connect all three wires separately. Direct Connection 2 Wire Extension ...

DO’S AND DON’TS Installation shall only be performed by qualified personnel and in accordance with local governing regulations. Do not route cable openly. For optimum isolation against electrical noise, run cable separately in a grounded metal conduit. Seal all thread connections to prevent ingress ...

APPLICATIONS The transducer is to be used only in the manner outlined in this instruction manual. Normally, the transducer requires no cleaning or maintenance. However, if performancechanges are observed, immediately shut down the level measurement system and perform athorough inspection, especially...

LIQUID APPLICATIONS - SUBMERGENCE In applications where flooding is possible the transducer ▼ can be fitted with a submergence shield. The shield acts as a bell to create an air pocket in front of the transducer face. Theassociated transceiver ▼ interprets this as a flooding condition, and reacts ac...

LIQUID APPLICATIONS - STANDPIPES In many applications access must be made via a standpipe. In such cases, Milltronics canprovide factory bonded flanged transducers or split flange kit that will readily mate to theflanged standpipe. Another option is to hang the transducer from a blind flange. The st...

LIQUID APPLICATIONS - VOLUME 1. Beam should not detect bin bottom. If this occurs use range extension parameters (on transceivers where available) to omit false echoes. A 6° beam angle represents a rise : run of about 20 : 1 (10 : 1 for 12°). In most tanks, the transducer should be centered as much ...

SOLIDS APPLICATIONS - TYPICAL 3. Transducer too close to material inlet. Falling material will intersect sound beam and cause erroneous readings or loss of echo. 1. Transducer angled to avoid seams in bin wall and aimed at discharge in order to read bin when empty. 2. Avoid intersecting bin wall sea...

SOLIDS APPLICATIONS - SPECIAL STORAGE BIN WITH AGITATOR 1. Transducer should be kept away from infeed.2. Where agitators are in use, use the Agitator Discrimination parameter on transceivers where available.3. Transducer should be aimed away from wall projections. DRYER - WOOD CHIPS 1. Transducer sh...

INSTALLATION DIAGRAM See Milltronics drawing number 0-9650017Z-DI-A for current drawing status. 7ML19981AK01.2 XPS/XCT Transducers 19

FOR CANADIAN HAZARDOUS INSTALLATIONS ONLY See Milltronics drawing number 0-8850004Z-DI-A for current drawing status. 20 XPS/XCT Transducers 7ML19981AK01.2

Notes Notes.fm Page 2 Thursday, October 11, 2001 8:48 AM