Siemens SPCK 421 - Manuals

Siemens SPCK 421 – User Manual in PDF format online.

Manuals:

User Manual

User Manual Siemens SPCK 421

Summary

Page 2 - Copyright

Copyright 2 Siemens AB A6V10209178 Security Products 26.09.2011 Copyright Technical specifications and availability subject to change without notice. © Copyright Siemens AB We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges the...

Page 3 - Table of contents

3 Siemens AB A6V10209178 Security Products 26.09.2011 Table of contents 1 Security ............................................................................................................... 4 1.1 Target group .........................................................................................

Page 4 - Security; Target group; General information; Liability claim; Operation; Dangerous situation due to false alarm; Service and maintenance; Danger of electrical shock during maintenance; Danger of electrical shock while cleaning the device

1 Security Target group 4 Siemens AB A6V10209178 Security Products 26.09.2011 1 Security 1.1 Target group The instructions in this documentation are directed at the following target group: Target readers Qualification Activity Condition of the product End user Instruction by technical specialists is...

Page 5 - Meaning of written warning notices

Security 1 Meaning of written warning notices 5 Siemens AB A6V10209178 Security Products 26.09.2011 1.3 Meaning of written warning notices Signal Word Type of Risk DANGER Danger of death or severe bodily harm. WARNING Possible danger of death or severe bodily harm. CAUTION Danger of minor bodily inj...

Page 6 - Directives and standards; EU directives; European Directive 2004/108/EC „Electromagnetic Compatibility”

2 Directives and standards EU directives 6 Siemens AB A6V10209178 Security Products 26.09.2011 2 Directives and standards 2.1 EU directives This product complies with the requirements of the European Directives 2004/108/EC “Directive of Electromagnetic Compatibility” and 2006/95/EC “Low Voltage Dire...

Page 7 - Introduction

Introduction 3 7 Siemens AB A6V10209178 Security Products 26.09.2011 3 Introduction The keypad is a wall-mounted interface that allows:  Engineers to program the system through the Engineer Programming menus (password protected) and to set/unset the system; a user can control the system on a day-to...

Page 8 - ok

3 Introduction 8 Siemens AB A6V10209178 Security Products 26.09.2011 4 ghi 5 jkl 6 mno 7 pqrs 8 tuv 9 wxyz 2 abc 3 def # 0 1 ok 1 2 3 4 5 6 7 8 3 LCD keypad 1 LCD display The keypad display (2 lines x 16 characters) shows all alert and warning messages and provides a visual interface for programming...

Page 10 - Overview of keypad types

4 Overview of keypad types 10 Siemens AB A6V10209178 Security Products 26.09.2011 4 Overview of keypad types Keypad type Model no. Basic Functionality Proximity Detection Audio Standard Keypad SPCK420 ✓ - - Keypad with PACE SPCK421 ✓ ✓ - Comfort Keypad SPCK620 ✓ - Comfort Keypad with Audio/CR SPCK62...

Page 11 - Using the keypad interface

Using the keypad interface 5 11 Siemens AB A6V10209178 Security Products 26.09.2011 5 Using the keypad interface ok 3 5 6 4 1 2 7 8 9 Keypad display 1 RIGHT SOFT KEY This key is used to select the option presented on the right side of the bottom line display. Possible values are: → SELECT to select ...

Page 12 - Prioritization of display messages

5 Using the keypad interface 12 Siemens AB A6V10209178 Security Products 26.09.2011 Possible values are: → EXIT to exit programming → BACK to return to previous menu 8 BOTTOM LINE OF DISPLAY In the IDLE state, this line is blank. In Programming mode, this line displays options available to the user....

Page 14 - User programming via the keypad; Setting and unsetting the system

6 User programming via the keypad Setting and unsetting the system 14 Siemens AB A6V10209178 Security Products 26.09.2011 6 User programming via the keypad User programming options are available using the LCD and Comfort Keypads. Menus and options available on the intrusion control panel is programm...

Page 15 - UNSET

User programming via the keypad 6 Setting and unsetting the system 15 Siemens AB A6V10209178 Security Products 26.09.2011 1 UNSET Performs an Unset on the system. If multiple areas are defined then each area is presented in a sub-menu. For a single area system this option is only presented when the ...

Page 16 - PARTSET

6 User programming via the keypad Setting and unsetting the system 16 Siemens AB A6V10209178 Security Products 26.09.2011 The system fails to set if there is an open or fault condition detected on an alarm zone when the FULLSET or PARTSET A/B option is selected. The keypad displays the zone number a...

Page 17 - CODED RESTORE

User programming via the keypad 6 Setting and unsetting the system 17 Siemens AB A6V10209178 Security Products 26.09.2011 closed again or a severed X-BUS connection re-established. The SPC system does NOT provide the Restore option without detection of the restored fault. Users may be restricted fro...

Page 18 - User Menus

6 User programming via the keypad User Menus 18 Siemens AB A6V10209178 Security Products 26.09.2011  A 6 digit reset code displays on the top line. 2. Provide 6 digit code to installer. 3. Receive newly generated code from installer. 4. Enter new code at the AUTH CODE prompt. 5. Press SELECT.  The...

Page 19 - SYSTEM STATUS; ISOLATE

User programming via the keypad 6 User Menus 19 Siemens AB A6V10209178 Security Products 26.09.2011 the size of their string. If the Security Grade of the system is set to ’Unrestricted’, then the INHIBIT, ISOLATE and GRANT ACCESS features may not be available in the user menu. A Standard or Manager...

Page 21 - TEST; WPA TEST

User programming via the keypad 6 User Menus 21 Siemens AB A6V10209178 Security Products 26.09.2011 6.2.5 TEST 1. Scroll to TEST and press SELECT. 2. Scroll to the desired programming option. 6.2.5.1 BELL TEST To perform a bell test:  Scroll to TEST > BELL TEST and press SELECT.  When BELL TEST...

Page 22 - AUDIBLE OPTIONS; EVENT LOG; CHIME

6 User programming via the keypad User Menus 22 Siemens AB A6V10209178 Security Products 26.09.2011 6.2.5.4 AUDIBLE OPTIONS The audible options are applied as indicators within a walk test. To set the audible options: 1. Scroll to AUDIBLE OPTIONS. 2. Press SELECT. 3. Scroll to one of the following o...

Page 23 - USERS; CHANGE PIN

User programming via the keypad 6 User Menus 23 Siemens AB A6V10209178 Security Products 26.09.2011 6.2.8 USERS Only Manager type users have the ability to add, edit, or delete users, unless a user profile has this capability assigned to their profile. Managers may add, edit or delete users with the...

Page 24 - SMS; SMS control

6 User programming via the keypad User Menus 24 Siemens AB A6V10209178 Security Products 26.09.2011 NOTICE Where USER DURESS feature is enabled, consecutive user codes (i.e. 2906, 2907) are not permitted, as entering this PIN from the keypad would activate a user duress event. NOTICE Engineer PINs s...

Page 25 - SMS CONTROL; SMS EVENTS; Adding a phone number

User programming via the keypad 6 User Menus 25 Siemens AB A6V10209178 Security Products 26.09.2011 6.2.10.1 SMS CONTROL There is a maximum of four users for SMS configuration on 1 panel and only 1 phone number for each user for use with SMS control functionality. It is important prerequisites such ...

Page 26 - Enabling a phone number; Reported events; SMS Commands

6 User programming via the keypad User Menus 26 Siemens AB A6V10209178 Security Products 26.09.2011 3. Enter a phone number and press ENTER.  The LCD displays UPDATED. 4. Press BACK to exit Enabling a phone number To enable a phone number for SMS [receipt]: 1. Scroll to SMS EVENTS and press SELECT....

Page 28 - DOOR CONTROL

6 User programming via the keypad User Menus 28 Siemens AB A6V10209178 Security Products 26.09.2011 The SMS operates using a standard protocol that is used in SMS telephones. Please note that some PSTN operators do not provide the service of SMS over PSTN. For SMS to operate over PSTN the following ...

Page 29 - REPORT TO ENG; ACCESS LOG

User programming via the keypad 6 User Menus 29 Siemens AB A6V10209178 Security Products 26.09.2011 For Swiss CAT 1 and CAT 2 regional requirements, when Engineer Access is granted, all areas must be unset otherwise the engineer will be denied access. 6.2.13 REPORT TO ENG The user can request that t...

Page 30 - Appendix; User rights

7 Appendix User rights 30 Siemens AB A6V10209178 Security Products 26.09.2011 7 Appendix 7.1 User rights Based on the operational features of the SPC system, described below, users have rights attributed to the user profiles. The installation engineer will inform users of their user rights assigned ...

Page 32 - User PINs; Zone chart

7 Appendix User PINs 32 Siemens AB A6V10209178 Security Products 26.09.2011 User Profile Default User type Description Users Manager User can configure user on the panel. Delay autoarm Standard* Manager User can delay auto setting. Bypass delay Standard Manager User can automatically override the Un...