Siemens SISTORE AX9 - Manuals

Safety 7 Siemens Building Technologies Fire Safety & Security Products 03.2009 2.2.3 Setup Damage due to unsuitable mounting location z Observe the environmental requirements recommended by the manufacturer. z Do not operate the device close to sources of powerful electromagnetic radiation. z Pr...

Safety 8 Siemens Building Technologies Fire Safety & Security Products 03.2009 Damage to the device due to overvoltage z Connect the device only to power sources with the specified voltage. Voltage supply requirements can be found on the power supply unit/type label. Dangerous situation due to f...

Safety 9 Siemens Building Technologies Fire Safety & Security Products 03.2009 2.3 Meaning of the written warning notices The severity of a hazard is indicated by the following written warning notices. Signal word Type of risk IMPORTANT Malfunctioning may result. 2.4 Meanings of the hazard symbo...

Directives and standards 10 Siemens Building Technologies Fire Safety & Security Products 03.2009 3 Directives and standards This product complies with the requirements of the following European directives. The EU declaration of conformity is available to the responsible agencies at: Siemens Bui...

Overview SISTORE AX devices 11 Siemens Building Technologies Fire Safety & Security Products 03.2009 4 Overview SISTORE AX devices This chapter shows the various SISTORE AX models including the scope of delivery of devices ex factory and in the Replacement Pool. 4.1 SISTORE AX4 Lite V2.0 Product...

Technical check 13 Siemens Building Technologies Fire Safety & Security Products 03.2009 5 Technical check This chapter describes the procedures for the technical verification of defective SISTORE AX devices. Please note that the procedures described below can only give an indication of unit con...

Technical check 14 Siemens Building Technologies Fire Safety & Security Products 03.2009 5.1.1 Config issues? 1. Verify BNC (SVHS) / VGA switch settings (either switch on the rear of the device or via Display button on the front of the device) 2. Stop recording when HDD is full 3. Configuration ...

Technical check 15 Siemens Building Technologies Fire Safety & Security Products 03.2009 5.2 Verification of secondary HDD Normal booting? ok? Booting without HDD? Functional Test not ok? ok? Faulty device from customer Replacement of HDD send device back to customer ok? Chap.3.2.1 Chap.3.2.2 Di...

Installation and replacement of hard disk drives 16 Siemens Building Technologies Fire Safety & Security Products 03.2009 6 Installation and replacement of hard disk drives This chapter describes the procedures to replace faulty HDDs and install extensions HDDs in the SISTORE AX. Independent of ...

Installation and replacement of hard disk drives 29 Siemens Building Technologies Fire Safety & Security Products 03.2009 6.5.1 Installation of the 1 st additional hard disk 1. Remove the HDD frame by loosening the four screws inside the device; then disconnect all cables from the hard disk unit...

Functional test 34 Siemens Building Technologies Fire Safety & Security Products 03.2009 7 Functional test The Functional Test ensures the proper operation of the device. In case the Functional Test is not successful even after inserting a new HDD, the devices shall be sent to the Service Centre...

Appendix 35 Siemens Building Technologies Fire Safety & Security Products 03.2009 8 Appendix 8.1 Troubleshooting The following table offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting the hotline. 8.1.1 SISTORE AX4 Lite V2....

Appendix 36 Siemens Building Technologies Fire Safety & Security Products 03.2009 8.1.3 SISTORE AX RAS NOTE RAS version 3.6 is required for SISTORE AX with SATA HDDs. Problem Possible solution No selection between Watch and Search displayed z Performance of PC not sufficient No display of live i...

Appendix 37 Siemens Building Technologies Fire Safety & Security Products 03.2009 8.2 Packaging for returning the HDD When returning a faulty HDD, package it in the same manner as it was delivered to protect the HDD unit from being damaged by shock, static electricity or humidity during transpor...

Disposal 38 Siemens Building Technologies Fire Safety & Security Products 03.2009 9 Disposal All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. This cro...