Siemens RWF40 - Manuals - manualsarea.com

Page 2 - This page is intentionally left blank...

2/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products This page is intentionally left blank…

Page 3 - Contents; This RWF40 hint manual is intended to; supplement; the RWF40 User Manual.; his symbol is used to draw your attention to a particular remark.

3/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products Contents 1. Introduction to hints manual. ........................................................................................ 3 1.1.1 How to use this manual .....................................................................................

Page 4 - Getting started with the RWF40 menu; Return to the Basic Display

2/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.1 Getting started with the RWF40 menu The RW F40 menu system has three Levels , beyond the Basic Display , the User Level , the Parameter Leve l and the Configuration Level . RW F40 user manual Section 6 Operation. 2.1.1 Start with t...

Page 5 - How to configure your RWF40

3/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.2 How to configure your RWF40 Shown at the right is the basic display. The current configuration of your specific controller will determine which levels you will be allowed to access. C112 must be xxx0 to access the configuration lev...

Page 6 - How to adjust parameters; Parameter level items summary:

4/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.3 How to adjust parameters RW F40 user manual Section 6.3 Shown at the right is the basic display. The current configuration of your specific controller will determine which levels you will be allowed to access. C112 must be xxx1 or ...

Page 7 - How to change a setpoint

5/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.4 How to change a setpoint (SP1, SP2, or dSP) RW F40 user manual Section 6.2 Shown at the right is the basic display. The current configuration of your specific controller will determine which levels you will be allowed to access. C1...

Page 9 - Manual operation continued...; Modulating burner, Modulating output; To exit manual operation

7/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.6 Manual operation continued… Modulating burner, 3-Position output Press and hold for 5 seconds, and release. The red LED above the manual icon turns on to indicate that the controller is now in the manual mode. Relay 2 and relay 3 w...

Page 10 - Technical Explanation; Conditions

8/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.7 Auto-tune (self-setting function) RW F40 user manual section 6.2.4 and 9.1 The RW F40 User manual refers to a ‘ self-setting-function ’ that for the purposes of this manual will be refered to as ‘ Auto-tune ’. Technical Explanation...

Page 11 - Configure; Configuration level values:; Set parameters; Parameter level values:; Set user level values

9/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.8 Setting up a standard temperature application Using a 1000 ohm Ni RTD, L & S # 556-541 –13 ° F to +203 ° F Configure If no keys are pressed for 20 seconds, the controller will exit this mode, and return to the basic display. Se...

Page 12 - Setting up a standard pressure application

10/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 2. Hints 2.9 Setting up a standard pressure application Using a QBE sensor, Siemens part # QBE620-P10 [P10 is 150PSI] Configure If no keys are pressed for 20 seconds, the controller will exit this mode, and return to the basic display. See Hin...

Page 14 - Your record of values; Configuration level items; Parameter level items; User level items

13/16 CC1B-Hints-en Preliminary 04.02.2003 HVAC Products 3. Notes 3.2 Your record of values RWF40 Setpoint Your Man. Ref. Display Setting Configuration level items ( Sec 6.4 ) Range Factory Sec 8.1 C111 Analog input 1, 2 and 3;D2 setpoint changeover / shift N /A 9030 Sec 8.1 / 8.2 C112 Limit compara...