Siemens HF36V305 - Manuals

2-1 CAUTIONS • DO NOT operate on a 2-wire extension cord during repair and use. • NEVER TOUCH any oven components or wiring during operation. • BEFORE TOUCHING any parts of the oven, always remove the power plug from the outlet. • For about 30 seconds after the oven stops, an electric charge remains...

3-1 INSTALLATION PRECAUTIONS ON INSTALLATION A. Plug the power supply cord into a 120V AC, 60Hz, single-phase power source with a capacity of 15Aor 20A. B. Avoid placing the unit in a location where there is direct heat or splashing water. C. Install the unit on the mounting plate firmly.D. Place th...

1. Display: The Display includes a clock and indicators to tell you time of day, cooking time settings and cooking functions selected. 2. Popcorn: Touch this pad when popping popcorn in your microwave oven. The oven’s sensor will tellthe oven how long to cook depending on theamount of humidity it de...

5-2 MATRIX CIRCUIT FOR TOUCH KEY BOARD SENSOR POPCORN DEFROST TIMER N.C RECIPE MORE ON/OFF T/TABLE DEFROST SENSOR POTATO START PIZZA SENSOR STOP CLEAR QUICK VENT HI/LO/OFF HI/LO/OFF LIGHT LESS FAVORITE EASY COOK CLOCK LIGHT SET-UP CONTROL TIME N.C N.C N.C HELP N.C N.C 3 8 REHEAT SENSOR 9 SENSOR VEGE...

6-1 GENERAL PRECAUTIONS IN USE A. Never operate the unit when it is empty. Operating the oven with no load may shorten thelife of the magnetron. Whenever cooking dry foods(dried fish, bread, etc.) or a small amount of food,be sure to put a glass of water into the cookingcompartment. The glass turnta...

PRELIMINARY A. SINCE NEARLY 2,100 VOLTS EXISTS IN SOME CIRCUITS OF THIS UNIT REPAIRS SHOULD BECARRIED OUT WITH GREAT CARE.The filament leads of magnetron carry HighVoltage with respect to ground. Extreme caution must be exercised. Never plug the unit into apower source to determine which component i...

7-2 CAUTIONS • Be sure to check microwave leakage prior to servicing the oven if the oven is operative prior toservicing. • The service personnel should inform the manufacture importer, or assembler of any certifiedoven unit found to have a microwave emission levelin excess of 5 mW/cm 2 and should r...

MEASUREMENT WITH THE OUTER CASEREMOVED (1) When you replace the magnetron, measure for microwave energy leakage before the outer caseis installed and after all necessary componentsare replaced or adjusted. Special care should betaken in measuring the following parts. - Around the magnetron- The wave...

IMPORTANT NOTES: UNIT MUST BE DISCONNECTED FROM ELEC-TRICAL OUTLET WHEN MAKING REPAIRS, RE-PLACEMENTS, ADJUSTMENTS AND CONTIN-UITY CHECKS. WAIT AT LEAST ONE MINUTE,UNTIL THE HIGH VOLTAGE CAPACITOR IN THEHIGH VOLTAGE POWER SUPPLY HAS FULLYDISCHARGED.THE CAPACITOR SHOULD BE DISCHARGED BYUSING INSULATE...

WIRE COLOR SYMBOL COLOR WH BK BR RD BL PK GY N.P. WHITE BLACK BROWN RED BLUE PINK GREY Not Provided Latch Board Secondary Interlock Switch Interlock Monitor Switch Primary Interlock Switch Latch Board WH(from H.V.Transformer) YL(from Fan Motor)WH(from Power Cord) WH(from cooktop lamp) Secondary Inte...

Vent Grille Controller (3 screws) Door MountingPlate (1 or 2 screws) Out Case Mount,All D. REMOVING MAGNETRON (Figures 11 Through 13) (1) Remove the vent grille by loosening two screws. (Figure 11) (2) Remove the outcase. See page 7-6.(3) Remove three tap tite screws securing the magnetron to the wa...

E. REMOVING STIRRER FAN (Figures 14 and 15) (1) Remove one rivet ASS'Y securing it to the oven upper plate by using knife blade. (2) Rotate slightly and pull out the stirrer fan cover.(3) Remove the stirrer fan. F. REMOVING DOOR (Figure 16) (1) Remove the vent grille by two screws securing it to the...

H. ASSEMBLING DOOR (1) When mounting the door assembly to the oven assembly, be sure to adjust the door assemblyparallel to the chassis. Also adjust so the door has noplay between the inner door surface and oven frameassembly. If the door assembly is not mountedproperly, microwaves may leak from the...

K. REMOVING THE TURNTABLE MOTOR (1) Remove the turntable.(2) Remove the turntable shaft VERY CAREFULLY with a slotted screwdriver. (Figure 20) (3) Remove the base plate by removing 7 screws securing it to the oven cavity. (Figure 21) (4) Disconnect the leadwire from the turntable motor terminals. (5...

7-12 ADJUSTMENT PROCEDURES To avoid possible exposure to microwave energyleakage, adjust the door latches and interlockswitches, using the following procedure. The Interlock Monitor and Primary Interlock Switch actas the final safety switch protecting the user frommicrowave energy. The terminals bet...

7-14 A. PRIMARY INTERLOCK SWITCH TEST When the door is opened slowly, an audible clickshould be heard at the same time or successivelyat intervals and the latches should activate theswitches with an audible click.If the latches do not activate the switches when thedoor is closed, the switches should...

7-15 - CAUTIONS - - DISCONNECT THE POWER SUPPLY CORD FROM THE WALL OUTLET WHENEVERREMOVINGING THE CABINET FROM THE UNIT.PROCEED WITH THE TESTS ONLY AFTERDISCHARGING THE HIGH VOLTAGE CAPACITORAND REMOVING THE WIRE LEADS FROM THEPRIMARY WINDING OF THE HIGH VOLTAGETRANSFORMER. (SEE FIGURE 24) - ALL OPE...

7-18 COMPONENTS TEST PROCEDURES RESULTS RELAY2 Check for continuity of relay 2 with anohm-meter.(Remove wire leads from relay 2 andoperate the unit.) NOTES: • A MICROWAVE ENERGY TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FORANY REASON. • MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSIT...